John W. Pierre
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
John W. Pierre has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- A. Balasubramanian
University of Alaska Fairbanks
2 shared publications - Arif Khan
Electrical and Computer Engineering, University of Wyoming, 4416 Laramie, Wyoming United States 82071-0333
2 shared publications - Daniel J. Trudnowski
Electrical Engineering Department, Montana Technological University, Butte, MT, USA
2 shared publications - Dongliang Duan
Department of Electrical and Computer Engineering, University of Wyoming, Laramie, WY, USA
2 shared publications - Jim Follum
Pacific Northwest National Laboratory, Richland, WA, USA
2 shared publications - Richard W. Wies
University of Alaska Fairbanks
2 shared publications
Latest Publications
- Open Access
- 18 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 32883-32900
Characterizing the Oscillatory Properties of Bulk Electric Systems
This paper presents a process for characterizing the oscillatory dynamics of a large bulk power system. As a demonstration, the process is applied to the Western Interconnection of North America. Several complementary analysis approaches, both new and existing, are employed to provide a comprehensive understanding of the oscillatory properties of the system. Established modal analysis techniques based on ringdown and mode-meter algorithms are utilized. In addition, we derive and apply methods based on spectral correlation analysis to identify modal frequencies, distinguish between modes that are closely spaced in frequency, and determine locations at which the modes are observable. Critical interarea modes are identified and characterized using actual-system synchrophasor measurements taken over several years of operation in concert with industry-standard simulation models. This includes 145 hours of PMU data and two planning base cases.
- 18 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 32883-32900
Open AccessCharacterizing the Oscillatory Properties of Bulk Electric Systems
This paper presents a process for characterizing the oscillatory dynamics of a large bulk power system. As a demonstration, the process is applied to the Western Interconnection of North America. Several complementary analysis approaches, both new and existing, are employed to provide a comprehensive understanding of the oscillatory properties of the system. Established modal analysis techniques based on ringdown and mode-meter algorithms are utilized. In addition, we derive and apply methods based on spectral correlation analysis to identify modal frequencies, distinguish between modes that are closely spaced in frequency, and determine locations at which the modes are observable. Critical interarea modes are identified and characterized using actual-system synchrophasor measurements taken over several years of operation in concert with industry-standard simulation models. This includes 145 hours of PMU data and two planning base cases.
- 19 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 40 (1) , 636-649
Frequency Support From Electric Vehicles for Advancing Renewable Energy Integration
The integration of renewable energy resources (RERs) in the modern power grid is increasing rapidly because of aggressive decarbonization goals, lower costs, and increased government investment. However, higher penetrations of inverter-based generation can lead to frequency stability issues because of reduced system inertia. This paper develops a framework for quantifying the contribution of electric vehicles (EVs) toward providing frequency support to the grid and thus increasing the penetration limit of renewable energy resources (RERs). EVs are considered to provide both inertial response and primary frequency response support to the grid. A stochastic approach incorporating the uncertainties associated with the behavior of EVs is developed to derive the discharge limit of EV aggregators. A multi-machine system frequency response (MM-SFR) model is developed, which incorporates the dynamic virtual inertia and droop coefficients of EV aggregators derived from the EV control modules. Frequency security constraints are developed from this MM-SFR model, which, along with the converter voltage security and low voltage ride-through constraints, are integrated within a nonlinear optimization framework to determine the RER integration limit. The efficacy of the proposed approach is validated using the RTS-GMLC test system.
- 19 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 40 (1) , 636-649
Frequency Support From Electric Vehicles for Advancing Renewable Energy Integration
The integration of renewable energy resources (RERs) in the modern power grid is increasing rapidly because of aggressive decarbonization goals, lower costs, and increased government investment. However, higher penetrations of inverter-based generation can lead to frequency stability issues because of reduced system inertia. This paper develops a framework for quantifying the contribution of electric vehicles (EVs) toward providing frequency support to the grid and thus increasing the penetration limit of renewable energy resources (RERs). EVs are considered to provide both inertial response and primary frequency response support to the grid. A stochastic approach incorporating the uncertainties associated with the behavior of EVs is developed to derive the discharge limit of EV aggregators. A multi-machine system frequency response (MM-SFR) model is developed, which incorporates the dynamic virtual inertia and droop coefficients of EV aggregators derived from the EV control modules. Frequency security constraints are developed from this MM-SFR model, which, along with the converter voltage security and low voltage ride-through constraints, are integrated within a nonlinear optimization framework to determine the RER integration limit. The efficacy of the proposed approach is validated using the RTS-GMLC test system.
- Open Access
- 1 January 2019
- Published by HICSS Conference Office
Visual Validation of Estimated Parametric Models of Power Systems Under Ambient Conditions
With the advent of synchrophasors, a number of measurement-based algorithms have been developed to estimate system modes using ambient data. The accuracy of these mode estimates depends on a number of factors, such as selection of the system order and data channels. To validate these mode estimates, two methods are proposed in this paper based on how well they agree with the observed data using the estimated parametric system model and observed data. In the proposed methods, the contribution of each mode estimate is analyzed to obtain a combination of system mode estimates to represent the model. The methodology of the proposed methods are illustrated using least-squares ARMA (LS-ARMA) method, which gives a parametric system model estimates. Results obtained by implementing the proposed methods on measured and simulated data validate the effectiveness of the proposed methods.
- 1 January 2019
- Published by HICSS Conference Office
Open AccessVisual Validation of Estimated Parametric Models of Power Systems Under Ambient Conditions
With the advent of synchrophasors, a number of measurement-based algorithms have been developed to estimate system modes using ambient data. The accuracy of these mode estimates depends on a number of factors, such as selection of the system order and data channels. To validate these mode estimates, two methods are proposed in this paper based on how well they agree with the observed data using the estimated parametric system model and observed data. In the proposed methods, the contribution of each mode estimate is analyzed to obtain a combination of system mode estimates to represent the model. The methodology of the proposed methods are illustrated using least-squares ARMA (LS-ARMA) method, which gives a parametric system model estimates. Results obtained by implementing the proposed methods on measured and simulated data validate the effectiveness of the proposed methods.
- 15 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 34 (2) , 1579-1588
Electromechanical Mode Estimation in the Presence of Periodic Forced Oscillations
Electromechanical modes are inherent to any interconnected power systems which provide a measure of the small-signal stability margin of the system. A number of algorithms have been developed for the estimation of these modes using synchrophasor measurements. However, most of these algorithms are not designed to operate in the presence of forced oscillations (FO). These FOs are results of periodic rogue input driving the system. When FOs are present, estimates of system modes can be biased depending on the frequency and the amplitude of the FOs. To tackle this problem, a new algorithm is proposed in this paper to estimate system modes in the presence of FOs. In the proposed method, the over-determined modified Yule-Walker method which is used to estimate autoregressive coefficients of an autoregressive moving average (ARMA) signal model is extended to an ARMA with exogenous input (ARMAX) model that incorporates the presence of FOs. Two versions of the proposed method are included in this paper based on the requirement of the information of the duration of FOs in the signal. Results obtained by implementing the proposed algorithm on simulated data and real-world data validate the effectiveness of both versions of the proposed method.
- 15 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 34 (2) , 1579-1588
Electromechanical Mode Estimation in the Presence of Periodic Forced Oscillations
Electromechanical modes are inherent to any interconnected power systems which provide a measure of the small-signal stability margin of the system. A number of algorithms have been developed for the estimation of these modes using synchrophasor measurements. However, most of these algorithms are not designed to operate in the presence of forced oscillations (FO). These FOs are results of periodic rogue input driving the system. When FOs are present, estimates of system modes can be biased depending on the frequency and the amplitude of the FOs. To tackle this problem, a new algorithm is proposed in this paper to estimate system modes in the presence of FOs. In the proposed method, the over-determined modified Yule-Walker method which is used to estimate autoregressive coefficients of an autoregressive moving average (ARMA) signal model is extended to an ARMA with exogenous input (ARMAX) model that incorporates the presence of FOs. Two versions of the proposed method are included in this paper based on the requirement of the information of the duration of FOs in the signal. Results obtained by implementing the proposed algorithm on simulated data and real-world data validate the effectiveness of both versions of the proposed method.
- 17 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 34 (2) , 1086-1094
Detection of Periodic Forced Oscillations in Power Systems Using Multitaper Approach
An algorithm based on Thomson's multitaper spectral estimation and harmonic analysis technique is proposed for the detection and frequency estimation of periodic forced oscillations in power system. Unlike traditional periodogram based techniques, the method does not rely on true ambient noise spectrum of the system, and can operate continuously in an online environment without requiring any system knowledge except synchrophasor measurements. It compares a test statistic derived from only measurements against a threshold, and the threshold is established from general expressions of the test statistic's distribution and probability of false alarm. Performance of the detector is explicitly expressed using probability of detection expression, and evaluated using simulation studies. Results upon application of this algorithm to field measured synchrophasor data suggest usability of the technique for forced oscillation detection in practical monitoring of power system.
- 17 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 34 (2) , 1086-1094
Detection of Periodic Forced Oscillations in Power Systems Using Multitaper Approach
An algorithm based on Thomson's multitaper spectral estimation and harmonic analysis technique is proposed for the detection and frequency estimation of periodic forced oscillations in power system. Unlike traditional periodogram based techniques, the method does not rely on true ambient noise spectrum of the system, and can operate continuously in an online environment without requiring any system knowledge except synchrophasor measurements. It compares a test statistic derived from only measurements against a threshold, and the threshold is established from general expressions of the test statistic's distribution and probability of false alarm. Performance of the detector is explicitly expressed using probability of detection expression, and evaluated using simulation studies. Results upon application of this algorithm to field measured synchrophasor data suggest usability of the technique for forced oscillation detection in practical monitoring of power system.
- 24 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 34 (1) , 782-790
Detection of Periodic Forced Oscillations in Power Systems Incorporating Harmonic Information
This paper derives an improved version of a periodogram detector for detecting forced oscillations (FO) in power systems using synchrophasor measurements. FOs are usually periodic in nature and are often accompanied with multiple harmonic components. This harmonic information of FOs is incorporated into the proposed periodogram detector, which significantly improves its detection performance for a given probability of a false alarm. The original periodogram detector carries out detection of each component of FOs separately, even though they are related through their harmonics. In the proposed periodogram detector, the detection algorithm is re--derived by incorporating harmonic information such that the detector now looks for a combination of harmonic components of FOs for detection. This derivation shows a significant improvement in the detection performance of the proposed periodogram detector as compared to the original one. This is also illustrated by the results obtained by implementing the proposed periodogram detector on the simulated and real world PMU measurements.
- 24 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Systems
- Vol. 34 (1) , 782-790
Detection of Periodic Forced Oscillations in Power Systems Incorporating Harmonic Information
This paper derives an improved version of a periodogram detector for detecting forced oscillations (FO) in power systems using synchrophasor measurements. FOs are usually periodic in nature and are often accompanied with multiple harmonic components. This harmonic information of FOs is incorporated into the proposed periodogram detector, which significantly improves its detection performance for a given probability of a false alarm. The original periodogram detector carries out detection of each component of FOs separately, even though they are related through their harmonics. In the proposed periodogram detector, the detection algorithm is re--derived by incorporating harmonic information such that the detector now looks for a combination of harmonic components of FOs for detection. This derivation shows a significant improvement in the detection performance of the proposed periodogram detector as compared to the original one. This is also illustrated by the results obtained by implementing the proposed periodogram detector on the simulated and real world PMU measurements.
- 1 July 2012
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 45 (16) , 989-1000
Overview of System Identification for Power Systems from Measured Responses
- 1 July 2012
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 45 (16) , 989-1000
Overview of System Identification for Power Systems from Measured Responses
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19325517,p. 1-8
Adaptive Filtering Techniques for Estimating Electromechanical Modes in Power Systems
Previous adaptive filtering algorithms using the least mean square (LMS) technique for estimating electromechanical modes in power systems imposed constraints arising from the variability and time of convergence of the filter estimates. Also these techniques assumed the power system data to be wide-sense stationary. This work presents a combination of adaptive filtering and block processing algorithms to overcome the constraints of variability and time of convergence of the mode estimates. This work also introduces an adaptive step size least mean squares (ASLMS) algorithm assuming the non-stationary nature of power system data. Finally, this paper investigates the use of an error tracking (ET) algorithm, a combination of LMS and ASLMS algorithms based on the estimation error of the adaptive filters. These techniques are applied to two sets of actual power system data recorded from the western North American power grid. The first data set recorded in June 2000 is 18.85 minutes long, and the second data set recorded in May 2005 is 180 minutes long. The June 2000 data has a lower damping ratio and is more non- stationary than the May 2005 data set in a signal processing sense. The results show that using the LMS in combination with the ASLMS algorithm designed to work in non-stationary environments reduces the variability of the mode estimates and the time of convergence.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19325517,p. 1-8
Adaptive Filtering Techniques for Estimating Electromechanical Modes in Power Systems
Previous adaptive filtering algorithms using the least mean square (LMS) technique for estimating electromechanical modes in power systems imposed constraints arising from the variability and time of convergence of the filter estimates. Also these techniques assumed the power system data to be wide-sense stationary. This work presents a combination of adaptive filtering and block processing algorithms to overcome the constraints of variability and time of convergence of the mode estimates. This work also introduces an adaptive step size least mean squares (ASLMS) algorithm assuming the non-stationary nature of power system data. Finally, this paper investigates the use of an error tracking (ET) algorithm, a combination of LMS and ASLMS algorithms based on the estimation error of the adaptive filters. These techniques are applied to two sets of actual power system data recorded from the western North American power grid. The first data set recorded in June 2000 is 18.85 minutes long, and the second data set recorded in May 2005 is 180 minutes long. The June 2000 data has a lower damping ratio and is more non- stationary than the May 2005 data set in a signal processing sense. The results show that using the LMS in combination with the ASLMS algorithm designed to work in non-stationary environments reduces the variability of the mode estimates and the time of convergence.
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 641-645
Electromechanical Modal Behavior During a 48 Hour Interval Using Nonparametric Methods
In this paper, the behavior of dominant electromechanical modes is investigated. Forty eight hours of Western Electricity Coordinating Council (WECC) power grid data from June 13, 2005 to June 15, 2005 is analyzed using fundamental nonparametric techniques. The analysis included taking the mean and variance of 10 minute data frames and a modification of the short-time Fourier transform (STFT) on 15 minute overlapping segments of data. These analyses provide information into how the electromechanical modes in the western power grid behave over a normal day and provide insight needed for more advanced analysis techniques.
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 641-645
Electromechanical Modal Behavior During a 48 Hour Interval Using Nonparametric Methods
In this paper, the behavior of dominant electromechanical modes is investigated. Forty eight hours of Western Electricity Coordinating Council (WECC) power grid data from June 13, 2005 to June 15, 2005 is analyzed using fundamental nonparametric techniques. The analysis included taking the mean and variance of 10 minute data frames and a modification of the short-time Fourier transform (STFT) on 15 minute overlapping segments of data. These analyses provide information into how the electromechanical modes in the western power grid behave over a normal day and provide insight needed for more advanced analysis techniques.