Richard W. Wies
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Richard W. Wies has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- A. Balasubramanian
University of Alaska Fairbanks
2 shared publications - John W. Pierre
University of Wyoming
2 shared publications - Ali Turan
University of Alaska Fairbanks, Electrical &Computer Engineering Dept, Duckering Building, Fairbanks, AK 99775, USA
1 shared publication - Metin Gokasan
Istanbul Technical University
1 shared publication - Seta Bogosyan
Univ Alaska, Dept Elect & Comp Engn, Fairbanks, AK 99775 USA
1 shared publication
Latest Publications
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19325517,p. 1-8
Adaptive Filtering Techniques for Estimating Electromechanical Modes in Power Systems
Previous adaptive filtering algorithms using the least mean square (LMS) technique for estimating electromechanical modes in power systems imposed constraints arising from the variability and time of convergence of the filter estimates. Also these techniques assumed the power system data to be wide-sense stationary. This work presents a combination of adaptive filtering and block processing algorithms to overcome the constraints of variability and time of convergence of the mode estimates. This work also introduces an adaptive step size least mean squares (ASLMS) algorithm assuming the non-stationary nature of power system data. Finally, this paper investigates the use of an error tracking (ET) algorithm, a combination of LMS and ASLMS algorithms based on the estimation error of the adaptive filters. These techniques are applied to two sets of actual power system data recorded from the western North American power grid. The first data set recorded in June 2000 is 18.85 minutes long, and the second data set recorded in May 2005 is 180 minutes long. The June 2000 data has a lower damping ratio and is more non- stationary than the May 2005 data set in a signal processing sense. The results show that using the LMS in combination with the ASLMS algorithm designed to work in non-stationary environments reduces the variability of the mode estimates and the time of convergence.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19325517,p. 1-8
Adaptive Filtering Techniques for Estimating Electromechanical Modes in Power Systems
Previous adaptive filtering algorithms using the least mean square (LMS) technique for estimating electromechanical modes in power systems imposed constraints arising from the variability and time of convergence of the filter estimates. Also these techniques assumed the power system data to be wide-sense stationary. This work presents a combination of adaptive filtering and block processing algorithms to overcome the constraints of variability and time of convergence of the mode estimates. This work also introduces an adaptive step size least mean squares (ASLMS) algorithm assuming the non-stationary nature of power system data. Finally, this paper investigates the use of an error tracking (ET) algorithm, a combination of LMS and ASLMS algorithms based on the estimation error of the adaptive filters. These techniques are applied to two sets of actual power system data recorded from the western North American power grid. The first data set recorded in June 2000 is 18.85 minutes long, and the second data set recorded in May 2005 is 180 minutes long. The June 2000 data has a lower damping ratio and is more non- stationary than the May 2005 data set in a signal processing sense. The results show that using the LMS in combination with the ASLMS algorithm designed to work in non-stationary environments reduces the variability of the mode estimates and the time of convergence.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21635137,p. 2984-2989
Development of Remotely Accessible Matlab/Simulink Based Electrical Drive Experiments
This paper describes the development of remotely accessible electrical drive sets for hands-on education in electrical machinery, electrical drive and control courses as well as certain aspects of motion control and power electronics. The remote access is provided via the developed client-server communication method using the TCP/IP protocol to run the Matlab/Simulink compatible electrical drive sets operating on the remote server side. The developed method allows access to the robotics and electrical drive test- beds, namely permanent magnet DC (PMDC), permanent magnet synchronous (PMSM), and induction motor (IM) motor-load sets, developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is the control unit used in all the electrical drive systems in the lab. The UAF remote laboratory web site can be accessed at: http://www.uaf.edu/ece/remote-lab.This paper describes the development of remotely accessible electrical drive sets for hands-on education in electrical machinery, electrical drive and control courses as well as certain aspects of motion control and power electronics. The remote access is provided via the developed client-server communication method using the TCP/IP protocol to run the Matlab/Simulink compatible electrical drive sets operating on the remote server side. The developed method allows access to the robotics and electrical drive test- beds, namele permanent magnet DC (PMDC), permanent magnet synchronous (PMSM), and induction motor (IM) motor-load sets, developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is the control unit used in all the electrical drive systems in the lab. The UAF remote laboratory web site can be accessed at: http://www.uaf.edu/ece/remote-lab.
- 1 June 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21635137,p. 2984-2989
Development of Remotely Accessible Matlab/Simulink Based Electrical Drive Experiments
This paper describes the development of remotely accessible electrical drive sets for hands-on education in electrical machinery, electrical drive and control courses as well as certain aspects of motion control and power electronics. The remote access is provided via the developed client-server communication method using the TCP/IP protocol to run the Matlab/Simulink compatible electrical drive sets operating on the remote server side. The developed method allows access to the robotics and electrical drive test- beds, namely permanent magnet DC (PMDC), permanent magnet synchronous (PMSM), and induction motor (IM) motor-load sets, developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is the control unit used in all the electrical drive systems in the lab. The UAF remote laboratory web site can be accessed at: http://www.uaf.edu/ece/remote-lab.This paper describes the development of remotely accessible electrical drive sets for hands-on education in electrical machinery, electrical drive and control courses as well as certain aspects of motion control and power electronics. The remote access is provided via the developed client-server communication method using the TCP/IP protocol to run the Matlab/Simulink compatible electrical drive sets operating on the remote server side. The developed method allows access to the robotics and electrical drive test- beds, namele permanent magnet DC (PMDC), permanent magnet synchronous (PMSM), and induction motor (IM) motor-load sets, developed for both on-site and remote use at the Control Laboratory in the University of Alaska Fairbanks (UAF). The client-server communication is developed in C/C++ using wxWidgets to communicate with the Matlab/Simulink downloadable DS1104, which is the control unit used in all the electrical drive systems in the lab. The UAF remote laboratory web site can be accessed at: http://www.uaf.edu/ece/remote-lab.
- 1 June 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Using Adaptive Step-Size Least Mean Squares (ASLMS) for Estimating Low-Frequency Electromechanical Modes in Power Systems
Information about the stability of heavily interconnected power systems is found in low-frequency electromechanical modes. This research complements model-based and measurement-based approaches to mode estimation typically requiring much computation and ringdown from a disturbance, respectively. This paper discusses an adaptive step-size least mean square algorithm (ASLMS) for estimating the electromechanical modes near real time in which the step size (mu) is adaptively controlled to improve the convergence time of the estimates compared to the LMS. A simple gradient vector (gamma) and a small positive constant (rho) are introduced for controlled adaptation of mu. The improvement in convergence performance of the frequency and damping estimates when compared to the LMS estimates is shown by applying the ASLMS to simulated data containing a stationary mode from a 19-machine test model and ambient power system data, while using an initial weight vector from previous ASLMS, LMS and block processing algorithm estimates
- 1 June 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Using Adaptive Step-Size Least Mean Squares (ASLMS) for Estimating Low-Frequency Electromechanical Modes in Power Systems
Information about the stability of heavily interconnected power systems is found in low-frequency electromechanical modes. This research complements model-based and measurement-based approaches to mode estimation typically requiring much computation and ringdown from a disturbance, respectively. This paper discusses an adaptive step-size least mean square algorithm (ASLMS) for estimating the electromechanical modes near real time in which the step size (mu) is adaptively controlled to improve the convergence time of the estimates compared to the LMS. A simple gradient vector (gamma) and a small positive constant (rho) are introduced for controlled adaptation of mu. The improvement in convergence performance of the frequency and damping estimates when compared to the LMS estimates is shown by applying the ASLMS to simulated data containing a stationary mode from a 19-machine test model and ambient power system data, while using an initial weight vector from previous ASLMS, LMS and block processing algorithm estimates