M. Kashiwagi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
M. Kashiwagi has a total of 71 co-authors. Here are the top co-authors by number of shared publications:
K. Watanabe
National Institutes for Quantum and Radiological Science and Technology (QST), Naka, 311-0193, Japan
5 shared publications- M. Hanada
Japan Atomic Energy Agency, 801-1 Mukouyama, Naka 319-0913, Japan
4 shared publications T. Inoue
Japan Atomic Energy Agency, 801‐1, Mukoyama, Naka 311‐0193, Japan
4 shared publicationsElizabeth Surrey
3 shared publicationsJ. Hiratsuka
National Institutes for Quantum and Radiological Science and Technology (QST), Naka, 311-0193, Japan
3 shared publicationsL. Svensson
ITER Organization, 13067 Saint‐Paul‐lez‐Durance Cede, France
3 shared publications
Latest Publications
- Open Access
- 28 December 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2052 (1) , 040014
Methods of beam emittance measurements of high power negative ion beams for NBIs
A thermal beam emittance measurement method is developed specifically to measure high power density beams for the ITER neutral beam injection system (NBI)’s. A one-dimensional carbon-fiber composite (CFC) target is utilized to withstand the high current densities of the negative hydrogen beam making the beam emittance measurement possible. Schemes for the emittance measurement were discussed since beam instabilities are present in various stages of the beam phase. The allowable time for the measurement will be less than 2 seconds and it’s necessary to monitor the CFC temperature to not exceed 2000°C. The proposed measurement scheme to minimize beam instabilities is through the constant operation of the arc discharge and pulsed beam extraction. Mechanical structures are also being designed for rapid measurements to select different phases of the beam and for implementing the measurement system to long pulse beam operation.
- 28 December 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2052 (1) , 040014
Open AccessMethods of beam emittance measurements of high power negative ion beams for NBIs
A thermal beam emittance measurement method is developed specifically to measure high power density beams for the ITER neutral beam injection system (NBI)’s. A one-dimensional carbon-fiber composite (CFC) target is utilized to withstand the high current densities of the negative hydrogen beam making the beam emittance measurement possible. Schemes for the emittance measurement were discussed since beam instabilities are present in various stages of the beam phase. The allowable time for the measurement will be less than 2 seconds and it’s necessary to monitor the CFC temperature to not exceed 2000°C. The proposed measurement scheme to minimize beam instabilities is through the constant operation of the arc discharge and pulsed beam extraction. Mechanical structures are also being designed for rapid measurements to select different phases of the beam and for implementing the measurement system to long pulse beam operation.
- 21 September 2018
- Published by AIP Publishing
- Vol. 2011 (1) , 050012
Numerical analysis of negative hydrogen ion beam optics by using 3D3V PIC simulation
The negative ion beam optics is studied quantitatively from the viewpoints of the heat loads due to the beam halo in the accelerator and the emittance of the negative ion beam by using the 3D3V PIC model combined with a Monte Carlo calculation, in which negative ion beam from plasma meniscus formation to the beam acceleration is modeled. As for the heat loads of the A2G and the GRG, the simulation result almost agrees with the experimental result. The simulation result indicates that the secondary electrons from the extractor also contribute to the heat load of the A1G. Moreover, the normalized rms emittance of the negative ion beam after the exit of the GRG are estimated to be around 0.25π mm mrad, which are compatible with the typical values of the negative ion sources.
- 21 September 2018
- Published by AIP Publishing
- Vol. 2011 (1) , 050012
Numerical analysis of negative hydrogen ion beam optics by using 3D3V PIC simulation
The negative ion beam optics is studied quantitatively from the viewpoints of the heat loads due to the beam halo in the accelerator and the emittance of the negative ion beam by using the 3D3V PIC model combined with a Monte Carlo calculation, in which negative ion beam from plasma meniscus formation to the beam acceleration is modeled. As for the heat loads of the A2G and the GRG, the simulation result almost agrees with the experimental result. The simulation result indicates that the secondary electrons from the extractor also contribute to the heat load of the A1G. Moreover, the normalized rms emittance of the negative ion beam after the exit of the GRG are estimated to be around 0.25π mm mrad, which are compatible with the typical values of the negative ion sources.
- 21 September 2018
- Published by AIP Publishing
- Vol. 2011 (1) , 060009
Benchmark of 3D multi-beamlet numerical models for the optics design of negative ion accelerators
The optics design of the multi-beamlet negative ion accelerator for MITICA has been verified by means of specific experiments in the NITS test facility at the QST lab, employing a scaled-down configuration having the same features as the accelerator of MITICA and ITER HNB. The experiments confirmed the validity of the accelerator design. However it was found that, in the presence of transverse magnetic field in the ion extraction stage, the ion beamlet deflection in numerical simulations was somehow underestimated with respect to the beamlet deflection inferred from thermal images of a CFC target exposed to the negative ion beam. A detailed benchmark, using also another (completely independent) numerical model of the accelerator, has allowed the identification of possible origins of the differences.
- 21 September 2018
- Published by AIP Publishing
- Vol. 2011 (1) , 060009
Benchmark of 3D multi-beamlet numerical models for the optics design of negative ion accelerators
The optics design of the multi-beamlet negative ion accelerator for MITICA has been verified by means of specific experiments in the NITS test facility at the QST lab, employing a scaled-down configuration having the same features as the accelerator of MITICA and ITER HNB. The experiments confirmed the validity of the accelerator design. However it was found that, in the presence of transverse magnetic field in the ion extraction stage, the ion beamlet deflection in numerical simulations was somehow underestimated with respect to the beamlet deflection inferred from thermal images of a CFC target exposed to the negative ion beam. A detailed benchmark, using also another (completely independent) numerical model of the accelerator, has allowed the identification of possible origins of the differences.
- 26 September 2011
- Published by AIP Publishing
- Vol. 1390 (1) , 545-554
Status of the 1 MeV Accelerator Design for ITER NBI
The beam source of neutral beam heating/current drive system for ITER is needed to accelerate the negative ion beam of 40A with at 1 MeV for 3600 sec. In order to realize the beam source, design and R&D works are being developed in many institutions under the coordination of ITER organization. The development of the key issues of the ion source including source plasma uniformity, suppression of co‐extracted electron in D beam operation and also after the long beam duration time of over a few 100 sec, is progressed mainly in IPP with the facilities of BATMAN, MANITU and RADI. In the near future, ELISE, that will be tested the half size of the ITER ion source, will start the operation in 2011, and then SPIDER, which demonstrates negative ion production and extraction with the same size and same structure as the ITER ion source, will start the operation in 2014 as part of the NBTF. The development of the accelerator is progressed mainly in JAEA with the MeV test facility, and also the computer simulation of beam optics also developed in JAEA, CEA and RFX. The full ITER heating and current drive beam performance will be demonstrated in MITICA, which will start operation in 2016 as part of the NBTF.- 26 September 2011
- Published by AIP Publishing
- Vol. 1390 (1) , 545-554
Status of the 1 MeV Accelerator Design for ITER NBI
The beam source of neutral beam heating/current drive system for ITER is needed to accelerate the negative ion beam of 40A with at 1 MeV for 3600 sec. In order to realize the beam source, design and R&D works are being developed in many institutions under the coordination of ITER organization. The development of the key issues of the ion source including source plasma uniformity, suppression of co‐extracted electron in D beam operation and also after the long beam duration time of over a few 100 sec, is progressed mainly in IPP with the facilities of BATMAN, MANITU and RADI. In the near future, ELISE, that will be tested the half size of the ITER ion source, will start the operation in 2011, and then SPIDER, which demonstrates negative ion production and extraction with the same size and same structure as the ITER ion source, will start the operation in 2014 as part of the NBTF. The development of the accelerator is progressed mainly in JAEA with the MeV test facility, and also the computer simulation of beam optics also developed in JAEA, CEA and RFX. The full ITER heating and current drive beam performance will be demonstrated in MITICA, which will start operation in 2016 as part of the NBTF.- 23 March 2009
- Published by AIP Publishing
- Vol. 1097 (1) , 421-430
Compensation of beamlet repulsion in a large negative ion source with a multi aperture accelerator
Excess heat loads to accelerator grids limit extension of pulse length in operation of the large negative ion sources with multi aperture accelerator. Part of the heat loads is caused by interception of deflected beamlets due to their space charge repulsion. In this paper, a beamlet steering technique using aperture offset was examined for compensation of the beamlet deflections utilizing a three dimensional beam analysis simulating the negative ion source of JT‐60 U. The beamlet deflection was analyzed in detail using fifty beamlets, which were extracted from apertures arranged in a lattice pattern of The simulation showed successful compensation of the beamlet deflection by aperture offsets defined according to the thin lens theory. Even if the beam energy was changed, the necessary aperture offset would not be changed maintaining the perveance and a ratio of extraction and acceleration voltage. In JT‐60 U, it was shown that the aperture offset of less than 1.0 mm would be enough to compensate the repulsion of all beamlets. When the magnetic field was applied for suppression of co‐extracted electrons, necessary aperture offset was estimated to be for 500 keV ion beam in JT‐60 U, in addition to the offset for the space charge repulsion. This result showed good agreements with the previous experimental results and design study of the JT‐60 U N‐NBI.- 23 March 2009
- Published by AIP Publishing
- Vol. 1097 (1) , 421-430
Compensation of beamlet repulsion in a large negative ion source with a multi aperture accelerator
Excess heat loads to accelerator grids limit extension of pulse length in operation of the large negative ion sources with multi aperture accelerator. Part of the heat loads is caused by interception of deflected beamlets due to their space charge repulsion. In this paper, a beamlet steering technique using aperture offset was examined for compensation of the beamlet deflections utilizing a three dimensional beam analysis simulating the negative ion source of JT‐60 U. The beamlet deflection was analyzed in detail using fifty beamlets, which were extracted from apertures arranged in a lattice pattern of The simulation showed successful compensation of the beamlet deflection by aperture offsets defined according to the thin lens theory. Even if the beam energy was changed, the necessary aperture offset would not be changed maintaining the perveance and a ratio of extraction and acceleration voltage. In JT‐60 U, it was shown that the aperture offset of less than 1.0 mm would be enough to compensate the repulsion of all beamlets. When the magnetic field was applied for suppression of co‐extracted electrons, necessary aperture offset was estimated to be for 500 keV ion beam in JT‐60 U, in addition to the offset for the space charge repulsion. This result showed good agreements with the previous experimental results and design study of the JT‐60 U N‐NBI.- 23 March 2009
- Published by AIP Publishing
- Vol. 1097 (1) , 353-363
Results of the SINGAP Neutral Beam Accelerator Experiment at JAEA
IRFM (CEA Cadarache) and JAEA Naka have entered into a collaboration in order to test a SINGAP [1] accelerator at the JAEA Megavolt Test Facility (MTF) at Naka, Japan. Whereas at the CEA testbed the acceleration current was limited to 0.1 A, at JAEA 0.5 A is available. This allows the acceleration of 15 H‐ beamlets in SINGAP to be tested and a direct comparison between SINGAP and MAMuG [2] to be made. High‐voltage conditioning in the SINGAP configuration has been quite slow, with 581 kV in vacuum achieved after 140 hours of conditioning. With 0.1 Pa of H2 gas present in the accelerator 787 kV could be achieved. The conditioning curve for MAMuG is 200 kV higher. SINGAP beam optics appears in agreement with calculation results. A beamlet divergence better than 5 mrad was obtained. SINGAP accelerates electrons to a higher energy than MAMuG. Measurements of the power intercepted on one of the electron dumps have been compared with EAMCC code [3] calculations. Based on the experiments described here, electron production by a SINGAP accelerator scaled up to ITER size was estimated to be too high for comfort
- 23 March 2009
- Published by AIP Publishing
- Vol. 1097 (1) , 353-363
Results of the SINGAP Neutral Beam Accelerator Experiment at JAEA
IRFM (CEA Cadarache) and JAEA Naka have entered into a collaboration in order to test a SINGAP [1] accelerator at the JAEA Megavolt Test Facility (MTF) at Naka, Japan. Whereas at the CEA testbed the acceleration current was limited to 0.1 A, at JAEA 0.5 A is available. This allows the acceleration of 15 H‐ beamlets in SINGAP to be tested and a direct comparison between SINGAP and MAMuG [2] to be made. High‐voltage conditioning in the SINGAP configuration has been quite slow, with 581 kV in vacuum achieved after 140 hours of conditioning. With 0.1 Pa of H2 gas present in the accelerator 787 kV could be achieved. The conditioning curve for MAMuG is 200 kV higher. SINGAP beam optics appears in agreement with calculation results. A beamlet divergence better than 5 mrad was obtained. SINGAP accelerates electrons to a higher energy than MAMuG. Measurements of the power intercepted on one of the electron dumps have been compared with EAMCC code [3] calculations. Based on the experiments described here, electron production by a SINGAP accelerator scaled up to ITER size was estimated to be too high for comfort
- 23 March 2009
- Published by AIP Publishing
- Vol. 1097 (1) , 335-343
Development of 1 MeV H[sup −] Accelerator at JAEA for ITER NB
This paper reports the recent activities at JAEA for the development of 1 MeV ion accelerator toward the ITER NBI. For the development of MAMuG accelerator, a 320 mA ion beam was successfully accelerated as the highest record in the world at the MeV class energy (796 keV). This was achieved by protecting the ion source from the high heat load by the backstream positive ions, which was produced during the high current ion acceleration. The SINGAP accelerator was tested at JAEA to compare the performance of the SINGAP and the MAMuG. This paper also reports the results of the SINGAP test and the comparison between the SINGAP and the MAMuG is discussed.- 23 March 2009
- Published by AIP Publishing
- Vol. 1097 (1) , 335-343
Development of 1 MeV H[sup −] Accelerator at JAEA for ITER NB
This paper reports the recent activities at JAEA for the development of 1 MeV ion accelerator toward the ITER NBI. For the development of MAMuG accelerator, a 320 mA ion beam was successfully accelerated as the highest record in the world at the MeV class energy (796 keV). This was achieved by protecting the ion source from the high heat load by the backstream positive ions, which was produced during the high current ion acceleration. The SINGAP accelerator was tested at JAEA to compare the performance of the SINGAP and the MAMuG. This paper also reports the results of the SINGAP test and the comparison between the SINGAP and the MAMuG is discussed.- 4 May 2005
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 763 (1) , 168
Acceleration of 100A/m2 Negative Hydrogen Ion Beams in a 1 MeV Vacuum Insulated Beam Source
In the ITER NB, conventional gas insulated beam source (GIBS) cannot be utilized because of the radiation‐induced conductivity of the insulation gas. Thus a vacuum insulated beam source (VIBS), where the whole beam source is immersed in vacuum, has been developed at JAERI. Recently, voltage holding capability of the VIBS was drastically improved by the large stress ring, which reduces the electric field concentration at the triple junction. Up to now, a high current density H− beam of 102 A/m2 (140 mA) at 800 keV has been accelerated. The beam acceleration was quite stable and accomplished for several hundreds shots. The degradation of the voltage holding due to the beam acceleration and/or Cs seeding was not observed. Thus the development of vacuum insulated beam source has solved technical issues of high voltage insulation of 1 MV level under the presence of the H− ion beams.
- 4 May 2005
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 763 (1) , 168
Acceleration of 100A/m2 Negative Hydrogen Ion Beams in a 1 MeV Vacuum Insulated Beam Source
In the ITER NB, conventional gas insulated beam source (GIBS) cannot be utilized because of the radiation‐induced conductivity of the insulation gas. Thus a vacuum insulated beam source (VIBS), where the whole beam source is immersed in vacuum, has been developed at JAERI. Recently, voltage holding capability of the VIBS was drastically improved by the large stress ring, which reduces the electric field concentration at the triple junction. Up to now, a high current density H− beam of 102 A/m2 (140 mA) at 800 keV has been accelerated. The beam acceleration was quite stable and accomplished for several hundreds shots. The degradation of the voltage holding due to the beam acceleration and/or Cs seeding was not observed. Thus the development of vacuum insulated beam source has solved technical issues of high voltage insulation of 1 MV level under the presence of the H− ion beams.
- 1 May 2004
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 75 (5) , 1819-1821
Acceleration of 1 MeV, 100 mA Class H− ion beams in a proof-of-principle accelerator for ITER
Development of an electrostatic accelerator for 1 MeV, 1 ampere class ion beams has been carried out as a Proof-of-Principle (PoP) of high current accelerators required in neutral beam system of fusion reactors such as ITER. A unique feature of such fusion oriented accelerators is to utilize vacuum insulation not only inside but also outside of the accelerator for high voltage insulation, since conventional gas insulation is not applicable due to excess radiation induced conductivity in the gas. The PoP accelerator is surrounded by an insulator stack as a vacuum boundary with a vacuum gap of 50 mm all around the accelerator. One of the key technologies to achieve insulation of MV voltage was reduction of electric field strength at triple junction of the insulator (made of FRP, fiber reinforced plastic) stack. By lowering the stress to 1.7 kV/mm, the accelerator sustained 1 MV stably for more than 2 hours. By tuning the ion source with/without cesium under stable accelerator operation, the PoP accelerator generated ion beams of 70 mA at 1 MeV, and 110 mA (80 A/m2) at 900 keV stably for several hundreds shots (pulse length, 0.5–1 s limited by the target). The dark current flowed inside/on the surface of the FRP insulator due to photoelectron effect was estimated to be less than μA in case of 0.1 A electron beam acceleration (maximum current observed in the experiment). This is in the same order to that due to conductivity of the insulator material. So far, high voltage breakdown due to photoelectron has never been observed.- 1 May 2004
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 75 (5) , 1819-1821
Acceleration of 1 MeV, 100 mA Class H− ion beams in a proof-of-principle accelerator for ITER
Development of an electrostatic accelerator for 1 MeV, 1 ampere class ion beams has been carried out as a Proof-of-Principle (PoP) of high current accelerators required in neutral beam system of fusion reactors such as ITER. A unique feature of such fusion oriented accelerators is to utilize vacuum insulation not only inside but also outside of the accelerator for high voltage insulation, since conventional gas insulation is not applicable due to excess radiation induced conductivity in the gas. The PoP accelerator is surrounded by an insulator stack as a vacuum boundary with a vacuum gap of 50 mm all around the accelerator. One of the key technologies to achieve insulation of MV voltage was reduction of electric field strength at triple junction of the insulator (made of FRP, fiber reinforced plastic) stack. By lowering the stress to 1.7 kV/mm, the accelerator sustained 1 MV stably for more than 2 hours. By tuning the ion source with/without cesium under stable accelerator operation, the PoP accelerator generated ion beams of 70 mA at 1 MeV, and 110 mA (80 A/m2) at 900 keV stably for several hundreds shots (pulse length, 0.5–1 s limited by the target). The dark current flowed inside/on the surface of the FRP insulator due to photoelectron effect was estimated to be less than μA in case of 0.1 A electron beam acceleration (maximum current observed in the experiment). This is in the same order to that due to conductivity of the insulator material. So far, high voltage breakdown due to photoelectron has never been observed.- 1 February 2002
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 73 (2) , 1090-1092
Development of a large volume negative-ion source for ITER neutral beam injector
Development of the negative-ion sources has been conducted to realize a high power neutral beam injector for International Thermonuclear Experimental Reactor (ITER). A high negative-ion current density of 31 mA/cm2 at a very low pressure of 0.1 Pa has been produced in a cesium seeded multicusp plasma generator which has the same concept of the ITER source. For a vacuum insulated accelerator, a voltage holding experiment of long distance vacuum gaps up to ∼1.8 m has been performed. It was clarified that the transition region of product pressure distance (pd) from the vacuum breakdown to the gas discharge is about 0.2 Pa m which is high enough from the operating region of the ITER source. A prototype vacuum insulated accelerator was fabricated based on the experiment and tested. A high-energy beam acceleration up to 970 keV, 37 mA, and 1 s has been successfully demonstrated.- 1 February 2002
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 73 (2) , 1090-1092
Development of a large volume negative-ion source for ITER neutral beam injector
Development of the negative-ion sources has been conducted to realize a high power neutral beam injector for International Thermonuclear Experimental Reactor (ITER). A high negative-ion current density of 31 mA/cm2 at a very low pressure of 0.1 Pa has been produced in a cesium seeded multicusp plasma generator which has the same concept of the ITER source. For a vacuum insulated accelerator, a voltage holding experiment of long distance vacuum gaps up to ∼1.8 m has been performed. It was clarified that the transition region of product pressure distance (pd) from the vacuum breakdown to the gas discharge is about 0.2 Pa m which is high enough from the operating region of the ITER source. A prototype vacuum insulated accelerator was fabricated based on the experiment and tested. A high-energy beam acceleration up to 970 keV, 37 mA, and 1 s has been successfully demonstrated.