Raul Ruiz-Garcia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Raul Ruiz-Garcia has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Pedro F. Mayuet
2 shared publications- Ruben Montano-Vega2 shared publications
Alejandro Sambruno
1 shared publication- Fermin Bañon
Department of Civil, Materials and Manufacturing Engineering, Engineering School, University of Malaga, 29071 Malaga, Spain
1 shared publication Francisco Jose Leon Arevalo
1 shared publication- Irene Del Sol
Universidad de Cádiz
1 shared publication
Latest Publications
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia Manufacturing
- Vol. 41, 233-240
Study of the influence of cutting parameters on surface quality in AWJM machining of thermoplastic matrix composites
- 1 January 2019
- Published by Elsevier in Procedia Manufacturing
- Vol. 41, 233-240
Open AccessStudy of the influence of cutting parameters on surface quality in AWJM machining of thermoplastic matrix composites
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia Manufacturing
- Vol. 41, 898-905
Study of kerf features on CFRP/UNS A97075 stacks machined by AWJM
- 1 January 2019
- Published by Elsevier in Procedia Manufacturing
- Vol. 41, 898-905
Open AccessStudy of kerf features on CFRP/UNS A97075 stacks machined by AWJM
- Open Access
Influence of Abrasive Waterjet Parameters on the Cutting and Drilling of CFRP/UNS A97075 and UNS A97075/CFRP Stacks
The incorporation of plastic matrix composite materials into structural elements of the aeronautical industry requires contour machining and drilling processes along with metallic materials prior to final assembly operations. These operations are usually performed using conventional techniques, but they present problems derived from the nature of each material that avoid implementing One Shot Drilling strategies that work separately. In this work, the study focuses on the evaluation of the feasibility of Abrasive Waterjet Machining (AWJM) as a substitute for conventional drilling for stacks formed of Carbon Fiber Reinforced Plastic (CFRP) and aluminum alloy UNS A97050 through the study of the influence of abrasive mass flow rate, traverse feed rate and water pressure in straight cuts and drills. For the evaluation of the straight cuts, Stereoscopic Optical Microscopy (SOM) and Scanning Electron Microscopy (SEM) techniques were used. In addition, the kerf taper through the proposal of a new method and the surface quality in different cutting regions were evaluated. For the study of holes, the macrogeometric deviations of roundness, cylindricity and straightness were evaluated. Thus, this experimental procedure reveals the conditions that minimize deviations, defects, and damage in straight cuts and holes obtained by AWJM.
Open AccessInfluence of Abrasive Waterjet Parameters on the Cutting and Drilling of CFRP/UNS A97075 and UNS A97075/CFRP Stacks
The incorporation of plastic matrix composite materials into structural elements of the aeronautical industry requires contour machining and drilling processes along with metallic materials prior to final assembly operations. These operations are usually performed using conventional techniques, but they present problems derived from the nature of each material that avoid implementing One Shot Drilling strategies that work separately. In this work, the study focuses on the evaluation of the feasibility of Abrasive Waterjet Machining (AWJM) as a substitute for conventional drilling for stacks formed of Carbon Fiber Reinforced Plastic (CFRP) and aluminum alloy UNS A97050 through the study of the influence of abrasive mass flow rate, traverse feed rate and water pressure in straight cuts and drills. For the evaluation of the straight cuts, Stereoscopic Optical Microscopy (SOM) and Scanning Electron Microscopy (SEM) techniques were used. In addition, the kerf taper through the proposal of a new method and the surface quality in different cutting regions were evaluated. For the study of holes, the macrogeometric deviations of roundness, cylindricity and straightness were evaluated. Thus, this experimental procedure reveals the conditions that minimize deviations, defects, and damage in straight cuts and holes obtained by AWJM.
- 1 January 2018
- Published by DAAAM International
- p. 1116-1124
Preliminary Characterization of the Rivet Shaving Process
- 1 January 2018
- Published by DAAAM International
- p. 1116-1124
Preliminary Characterization of the Rivet Shaving Process