Mark Mehos
Mark Mehos has a total of 93 co-authors. Here are the top co-authors by number of shared publications:
Paul Denholm
National Renewable Energy Lab. (NREL), Golden, CO (United States)
5 shared publicationsCraig Turchi
National Renewable Energy Lab. (NREL), Golden, CO (United States)
4 shared publicationsBruce Kelly
Solar Dynamics, Broomfield, CO (United States)
3 shared publicationsClifford Ho
Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)
3 shared publications- Craig Turchi
National Renewable Energy Laboratory (NREL), Golden, CO (United States)
3 shared publications Hank Price
Solar Dynamics, Broomfield, CO (United States)
3 shared publications
Latest Publications
- Open Access
- 27 January 2026
- Published by Office of Scientific and Technical Information (OSTI)
Analysis of Molten Salt Thermal Energy Storage Tank Sizing and Preheating
Molten Salt Thermal energy storage (TES) is essential for concentrating solar power (CSP) plants, enhancing their capacity factor and dispatchability to ultimately reduce electricity costs. This technology is becoming more important for other technologies including nuclear power, thermal-electrical storage, and concentrating solar thermal (CST). While molten salt TES tanks have been successfully deployed in lower-temperature parabolic-trough plants, the current state-of-the-art central receiver systems operating at temperatures up to 565 degrees Celsius have experienced costly and frequent failures. These failures are associated with the immaturity of the technology and problems in tank design, fabrication, commissioning and, sometimes, aggressive operation. A primary contributing factor is the absence of a dedicated technical standard for high-temperature molten nitrate TES tanks; designers must currently rely on existing codes like API 650 and ASME Section II, which are insufficient because they fail to account for the unique demands of high temperatures, thermal cycling, and transient conditions. In March 2024, NLR released the Failure Analysis for Molten Salt Thermal Energy Tanks for In-Service CSP Plants report (NREL/TP-5700-89036) that summarized the failure mechanism and factors contributing to these failures. This report presented detailed information on the molten salt tank model formulation and validation and the employment of the model to evaluate the temperature, stress, and deformation distribution in a representative tank design for typical plant operation conditions. The report also presented a set recommendations for future work to improve tank's reliability including the consideration of new base materials and welding fillers, salt distribution ring optimization, feasibility analysis of post weld heat treatment, reevaluation and enhancement of welding procedure specification, and implementation of safety operation protocols. This report, part of the DOE SETO-funded project, agreement DE-EE0038475 - 'Failure analysis of molten salt tanks for in-service CSP plants,' investigates the efficacy of the new CSP industry hypothesis to use smaller TES tanks with thicker floors to reduce failure susceptibility. It was found that while residual stress and distortion from welding fabrication are independent of the tank diameter, a significant reduction in stress during operation was achieved with the smaller, thicker-floored design, thereby providing evidence to support this new CSP plant hypothesis. The preheating analysis results, in turn, are still in an early stage and require further research to provide an accurate quantification of the effect of this process on residual stress and distortion in the tank floor. Resolving failures in molten salt TES tanks is crucial not only for CSP, but also for other applications considering these TES technologies, including nuclear, geothermal, and direct heat thermal energy storage for industrial processes.
- 27 January 2026
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessAnalysis of Molten Salt Thermal Energy Storage Tank Sizing and Preheating
Molten Salt Thermal energy storage (TES) is essential for concentrating solar power (CSP) plants, enhancing their capacity factor and dispatchability to ultimately reduce electricity costs. This technology is becoming more important for other technologies including nuclear power, thermal-electrical storage, and concentrating solar thermal (CST). While molten salt TES tanks have been successfully deployed in lower-temperature parabolic-trough plants, the current state-of-the-art central receiver systems operating at temperatures up to 565 degrees Celsius have experienced costly and frequent failures. These failures are associated with the immaturity of the technology and problems in tank design, fabrication, commissioning and, sometimes, aggressive operation. A primary contributing factor is the absence of a dedicated technical standard for high-temperature molten nitrate TES tanks; designers must currently rely on existing codes like API 650 and ASME Section II, which are insufficient because they fail to account for the unique demands of high temperatures, thermal cycling, and transient conditions. In March 2024, NLR released the Failure Analysis for Molten Salt Thermal Energy Tanks for In-Service CSP Plants report (NREL/TP-5700-89036) that summarized the failure mechanism and factors contributing to these failures. This report presented detailed information on the molten salt tank model formulation and validation and the employment of the model to evaluate the temperature, stress, and deformation distribution in a representative tank design for typical plant operation conditions. The report also presented a set recommendations for future work to improve tank's reliability including the consideration of new base materials and welding fillers, salt distribution ring optimization, feasibility analysis of post weld heat treatment, reevaluation and enhancement of welding procedure specification, and implementation of safety operation protocols. This report, part of the DOE SETO-funded project, agreement DE-EE0038475 - 'Failure analysis of molten salt tanks for in-service CSP plants,' investigates the efficacy of the new CSP industry hypothesis to use smaller TES tanks with thicker floors to reduce failure susceptibility. It was found that while residual stress and distortion from welding fabrication are independent of the tank diameter, a significant reduction in stress during operation was achieved with the smaller, thicker-floored design, thereby providing evidence to support this new CSP plant hypothesis. The preheating analysis results, in turn, are still in an early stage and require further research to provide an accurate quantification of the effect of this process on residual stress and distortion in the tank floor. Resolving failures in molten salt TES tanks is crucial not only for CSP, but also for other applications considering these TES technologies, including nuclear, geothermal, and direct heat thermal energy storage for industrial processes.
- Open Access
- 1 January 2025
- Published by National Laboratory of the Rockies
Field Measurements of Wind Loads on Heliostats in an Operational CSP Tower Plant
- 1 January 2025
- Published by National Laboratory of the Rockies
Open AccessField Measurements of Wind Loads on Heliostats in an Operational CSP Tower Plant
- Open Access
- 1 January 2025
- Published by National Laboratory of the Rockies
Improving Near-Surface Wind Data for CSP Collector Design and Performance
- 1 January 2025
- Published by National Laboratory of the Rockies
Open AccessImproving Near-Surface Wind Data for CSP Collector Design and Performance
- Open Access
- 25 March 2024
- Published by Office of Scientific and Technical Information (OSTI)
Failure Analysis for Molten Salt Thermal Energy Storage Tanks for In-Service CSP Plants
Thermal Energy Storage (TES) is a fundamental component in concentrating solar power (CSP) plants to increase the plant's dispatchability, capacity factor, while reducing the levelized cost of electricity. In central receivers CSP plants, nitrate molten salts have been used for several years for operation temperatures of up to 565 degrees C. Despite many efforts to advance nitrate salt to higher operation temperatures (even considering a replacement with molten chloride salts) to achieve higher energy conversion efficiencies, the 565 degrees C temperature is currently considered the state-of-the art. Although molten salt tanks have been broadly deployed in commercial CSP plants worldwide, several failures have been reported in these tanks after a few months or years of operation, causing significant economic loss and mistrust in CSP technologies. Most of these failures are associated with the infancy of the technology and multiple issues related to tank design, fabrication, commissioning, and aggressive operation. A technical standard dedicated to the design and fabrication of molten nitrate TES tanks does not exist today. Current in-service molten salt tanks have been generally designed based on the American Petroleum Institute's (API) 650 and ASME Section II standards. The API 650 code provides guidelines for dimensions and fabrication for oil storage tanks up to 260 degrees C. The ASME standard provides allowable stress values for various materials at a range of temperatures and conditions. Both standards seem to be limited for molten salt TES tanks where high temperatures, thermal cycling, and transient conditions are expected. In 2020, NREL released the Concentrating Solar Power Best Practices Study (NREL/TP-5500-75763) that summarized multiple issues in CSP plants, along with potential alternatives and recommendations to address those issues based on information collected from participants representing about 80% of operating CSP plants in the world. One of the recommendations from this study was the development of accurate and validated models to evaluate the plant's transient operation, capable of capturing the effect of short-term clouds and operator response, while being flexible in being adapted to various spatial and temporal resource data. The "Failure Analysis for Molten Salt Thermal Energy Tanks for In-Service CSP Plants" project was inspired on this recommendation and was focused on (1) the development and validation of a physics-based model for a representative, commercial-scale molten salt tank, (2) performing simulations to evaluate the behavior of the tank as a function of typical plant operation conditions, (3) understanding tank failures mechanisms, (4) determining the residual stress and distortion in the tank floor after welding fabrication and evaluating their impact in the stresses developed in the tank during operation, (5) assessing the impact of key operation parameters on the temperature and stress distribution, (6) conduct a preliminary evaluation of design features to reduce stress and improve tank's reliability, and (7) estimate the tank's service life based on the stress developed under diverse operation scenarios. From the analysis conducted in the project and presented in this report, it was found that maximum stresses surpassing the yield strength point of the stainless steel (SS) 347H are developed on the tank floor near the perimeter. These large stresses are strongly influenced by the initial residual stresses and distortion of the tank floor after welding fabrication. During operation, large stresses are developed in the tank floor at high operation temperatures with large salt inventory levels during transient operation. High stresses are also related to elevated temperature gradients in the tank floor that could be attributed to insufficient mixing within the salt inflow and the salt inventory. Based on the analysis, creep is the predominant failure mechanism. However, the large stress levels could favor the plastic deformation into buckles, and crack formation due to stress relaxation cracking during cycle operation. A lifetime below 3 years was estimated for the typical plant operation conditions and a specific initial residual stress and deformation distribution of the tank floor. The estimated life agrees with the service time to failure reported in several commercial molten salt tanks. Desing and operation guidelines can be extracted from the analysis presented in this report, which could be adopted by tank manufacturers and CSP operators to advance toward an ultimate solution for tank failures by reducing residual and operational stresses to achieve a tank service life of more than 30 years. Addressing failures in molten salt TES tanks is fundamental for the CSP industry's survivability, but it is also important for other industrial and power generation applications using this technology, including nuclear and concentrating solar thermal.
- 25 March 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessFailure Analysis for Molten Salt Thermal Energy Storage Tanks for In-Service CSP Plants
Thermal Energy Storage (TES) is a fundamental component in concentrating solar power (CSP) plants to increase the plant's dispatchability, capacity factor, while reducing the levelized cost of electricity. In central receivers CSP plants, nitrate molten salts have been used for several years for operation temperatures of up to 565 degrees C. Despite many efforts to advance nitrate salt to higher operation temperatures (even considering a replacement with molten chloride salts) to achieve higher energy conversion efficiencies, the 565 degrees C temperature is currently considered the state-of-the art. Although molten salt tanks have been broadly deployed in commercial CSP plants worldwide, several failures have been reported in these tanks after a few months or years of operation, causing significant economic loss and mistrust in CSP technologies. Most of these failures are associated with the infancy of the technology and multiple issues related to tank design, fabrication, commissioning, and aggressive operation. A technical standard dedicated to the design and fabrication of molten nitrate TES tanks does not exist today. Current in-service molten salt tanks have been generally designed based on the American Petroleum Institute's (API) 650 and ASME Section II standards. The API 650 code provides guidelines for dimensions and fabrication for oil storage tanks up to 260 degrees C. The ASME standard provides allowable stress values for various materials at a range of temperatures and conditions. Both standards seem to be limited for molten salt TES tanks where high temperatures, thermal cycling, and transient conditions are expected. In 2020, NREL released the Concentrating Solar Power Best Practices Study (NREL/TP-5500-75763) that summarized multiple issues in CSP plants, along with potential alternatives and recommendations to address those issues based on information collected from participants representing about 80% of operating CSP plants in the world. One of the recommendations from this study was the development of accurate and validated models to evaluate the plant's transient operation, capable of capturing the effect of short-term clouds and operator response, while being flexible in being adapted to various spatial and temporal resource data. The "Failure Analysis for Molten Salt Thermal Energy Tanks for In-Service CSP Plants" project was inspired on this recommendation and was focused on (1) the development and validation of a physics-based model for a representative, commercial-scale molten salt tank, (2) performing simulations to evaluate the behavior of the tank as a function of typical plant operation conditions, (3) understanding tank failures mechanisms, (4) determining the residual stress and distortion in the tank floor after welding fabrication and evaluating their impact in the stresses developed in the tank during operation, (5) assessing the impact of key operation parameters on the temperature and stress distribution, (6) conduct a preliminary evaluation of design features to reduce stress and improve tank's reliability, and (7) estimate the tank's service life based on the stress developed under diverse operation scenarios. From the analysis conducted in the project and presented in this report, it was found that maximum stresses surpassing the yield strength point of the stainless steel (SS) 347H are developed on the tank floor near the perimeter. These large stresses are strongly influenced by the initial residual stresses and distortion of the tank floor after welding fabrication. During operation, large stresses are developed in the tank floor at high operation temperatures with large salt inventory levels during transient operation. High stresses are also related to elevated temperature gradients in the tank floor that could be attributed to insufficient mixing within the salt inflow and the salt inventory. Based on the analysis, creep is the predominant failure mechanism. However, the large stress levels could favor the plastic deformation into buckles, and crack formation due to stress relaxation cracking during cycle operation. A lifetime below 3 years was estimated for the typical plant operation conditions and a specific initial residual stress and deformation distribution of the tank floor. The estimated life agrees with the service time to failure reported in several commercial molten salt tanks. Desing and operation guidelines can be extracted from the analysis presented in this report, which could be adopted by tank manufacturers and CSP operators to advance toward an ultimate solution for tank failures by reducing residual and operational stresses to achieve a tank service life of more than 30 years. Addressing failures in molten salt TES tanks is fundamental for the CSP industry's survivability, but it is also important for other industrial and power generation applications using this technology, including nuclear and concentrating solar thermal.
- Open Access
- 1 January 2023
- Published by Office of Scientific and Technical Information (OSTI)
FY19-FY21 Concentrating Solar Power Systems Analysis Final Report
This technical report summarizes work done by NREL over a 3-year period for the Concentrating Solar Power (CSP) Systems Analysis project for fiscal years 2019-2021 (FY19-FY21) in support of the Solar Energies Technology Office of the U.S. Department of Energy. The goal of the CSP Systems Analysis project is to provide timely and accurate CSP cost data to the U.S. Department of Energy's (DOE's) Solar Energy Technologies Office (SETO) and to project the performance and cost of emerging CSP technologies to inform research directions and industry investment.
- 1 January 2023
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessFY19-FY21 Concentrating Solar Power Systems Analysis Final Report
This technical report summarizes work done by NREL over a 3-year period for the Concentrating Solar Power (CSP) Systems Analysis project for fiscal years 2019-2021 (FY19-FY21) in support of the Solar Energies Technology Office of the U.S. Department of Energy. The goal of the CSP Systems Analysis project is to provide timely and accurate CSP cost data to the U.S. Department of Energy's (DOE's) Solar Energy Technologies Office (SETO) and to project the performance and cost of emerging CSP technologies to inform research directions and industry investment.
- 15 March 2022
- Published by Office of Scientific and Technical Information (OSTI)
Integrated Heat Pump Thermal Storage and Power Cycle for CSP (Final Technical Report)
Pumped thermal energy storage (PTES) is a storage system that stores electricity in thermal reservoirs. In this project, methods of integrating PTES with concentrating solar power (CSP) systems were investigated and their feasibility evaluated. Hybrid "solar-PTES" devices can provide both flexible renewable power generation as well as a variety of electricity storage services. Techno-economic models of PTES and solar-PTES were developed and used to assess their performance, cost, and commercial viability. Systems were optimized using multi-objective optimization techniques. The value that these storage devices provide to the grid was estimated using production cost modelling. Key advances made in this project include the development of detailed techno-economic models that improve state-of-the-art assessments of these technologies. Off-design models were developed and used in grid-analysis models. This work describes for the first time how PTES and solar-PTES behave over a range of operating points and assesses the value that these systems can provide to the electrical grid. Feedback was obtained from experts in the field, which clarified key technological and economic barriers that must be addressed to improve the feasibility of these devices.
- 15 March 2022
- Published by Office of Scientific and Technical Information (OSTI)
Integrated Heat Pump Thermal Storage and Power Cycle for CSP (Final Technical Report)
Pumped thermal energy storage (PTES) is a storage system that stores electricity in thermal reservoirs. In this project, methods of integrating PTES with concentrating solar power (CSP) systems were investigated and their feasibility evaluated. Hybrid "solar-PTES" devices can provide both flexible renewable power generation as well as a variety of electricity storage services. Techno-economic models of PTES and solar-PTES were developed and used to assess their performance, cost, and commercial viability. Systems were optimized using multi-objective optimization techniques. The value that these storage devices provide to the grid was estimated using production cost modelling. Key advances made in this project include the development of detailed techno-economic models that improve state-of-the-art assessments of these technologies. Off-design models were developed and used in grid-analysis models. This work describes for the first time how PTES and solar-PTES behave over a range of operating points and assesses the value that these systems can provide to the electrical grid. Feedback was obtained from experts in the field, which clarified key technological and economic barriers that must be addressed to improve the feasibility of these devices.
- 1 September 2021
- Published by Office of Scientific and Technical Information (OSTI)
The Role of Concentrating Solar-Thermal Technologies in a Decarbonized U.S. Grid
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 September 2021
- Published by Office of Scientific and Technical Information (OSTI)
The Role of Concentrating Solar-Thermal Technologies in a Decarbonized U.S. Grid
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 June 2020
- Published by Office of Scientific and Technical Information (OSTI)
Concentrating Solar Power Best Practices Study
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 June 2020
- Published by Office of Scientific and Technical Information (OSTI)
Concentrating Solar Power Best Practices Study
The U.S. Department of Energy's Office of Scientific and Technical Information
- 9 May 2019
- Published by Office of Scientific and Technical Information (OSTI)
CSP Systems Analysis - Final Project Report
The U.S. Department of Energy's Office of Scientific and Technical Information
- 9 May 2019
- Published by Office of Scientific and Technical Information (OSTI)
CSP Systems Analysis - Final Project Report
The U.S. Department of Energy's Office of Scientific and Technical Information
- 17 January 2019
- Published by Office of Scientific and Technical Information (OSTI)
The Potential Role of Concentrating Solar Power within the Context of DOE's 2030 Solar Cost Targets
The U.S. Department of Energy's Office of Scientific and Technical Information
- 17 January 2019
- Published by Office of Scientific and Technical Information (OSTI)
The Potential Role of Concentrating Solar Power within the Context of DOE's 2030 Solar Cost Targets
The U.S. Department of Energy's Office of Scientific and Technical Information