Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohammad Ali Dastan Diznab has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    RCMT, electrical conductivity, and mechanical characterization of polypropylene fiber-reinforced LECA mortar

    by Dorsa Taghvaei, Pouriya Behzad, Setareh Ghaderan, Mohammad Ali Dastan Diznab

  • Open Access

    Mechanical performance of eco-friendly cement mortar incorporating aluminum dross under acidic exposure

    by Mohammad Ali Dastan Diznab, Fatemeh Yousefi Karim Abadi, Setareh Ghaderan, Mehran Bonyadi

    The incorporation of aluminum dross into cement-based mortars offers potential benefits for environmental sustainability; however, it may adversely affect the mechanical performance of the material. This study integrates experimental testing with statistical analysis to evaluate the influence of aluminum dross on the mechanical properties of mortar specimens exposed to sulfuric acid (pH 1.5). Compressive strength, flexural strength, and mass variation were measured for mortars containing different aluminum dross contents. Following 28 days of water curing, the specimens were immersed in sulfuric acid for periods ranging from 0 to 90 days. The results indicate that exposure to sulfuric acid led to progressive deterioration in all mortar mixtures, with average reductions of 39% in compressive strength after 14 days and about 80% after 90 days. Before acid exposure, increasing aluminum dross content reduced the initial mechanical strength by up to 28% compared with the control mixture. Under prolonged acidic conditions, slag-containing mortars—particularly those incorporating 10% and 15% aluminum dross—exhibited reduced strength loss and enhanced acid resistance compared to slag-free control specimens. Statistical analysis demonstrated strong correlations between mechanical properties, acid exposure duration, and mass loss, whereas the effect of aluminum dross content was less significant. These findings underline both the potential benefits and the practical limitations of using aluminum dross in sustainable cement mortar applications subjected to acidic exposure.

  • A Strut-and-Tie Model for Predicting the Shear Strength of Exterior Beam–Column Joints Strengthened with Fiber-Reinforced Polymers

    by Reza Mashhadi, Mohammad Ali Dastan Diznab, Fariborz M. Tehrani

    This paper presents a new strut-and-tie model (STM) based on provisions of ACI 318-19 and ACI 440.2R-17 for estimating the shear strength of fiber-reinforced polymer (FRP)-strengthened exterior joints. Beam–column joints are vulnerable elements in reinforced-concrete structures subjected to seismic loadings and similar extreme demands. The FRP strengthening technique offers numerous advantages for retrofitting joints in existing structures with inadequate reinforcement or confinement. The design of FRP-strengthened joints requires the development of reliable procedures, including equations to predict the shear strength of the joint. Existing literature and research on STM warrant the development of simple, reliable, and practical specifications applied to a wide range of design criteria. The proposed method involves an STM model containing horizontal and vertical mechanisms. The methodology compares predicted joint shear strength results with existing experimental results to obtain a reliable design approach. This comparison, along with verification of alternative analytical results, indicates the appropriateness of the presented model for predicting the shear strength of FRP-strengthened joints. Results contribute to the enhancement and efficiency of the practical design of these joints.


  • Strut-and-Tie Model for Predicting the Shear Strength of Exterior Beam-Column Joints without Transverse Reinforcement

    by Reza Mashhadi, Mohammad Ali Dastan Diznab, Fariborz M. Tehrani

    This paper presents an analytical approach to predicting the shear strength of exterior beam-column joints without transverse reinforcement using a strut-and-tie model (STM). The proposed model contains a single diagonal strut with varied angle and width for modeling the shear behavior. Modeling analyses involve three approaches to determine the width and angle of the diagonal strut for the best prediction of experimental shear strength values. An experimental database of 25 exterior beam-column joints without transverse reinforcement and without confining out-of-plane members was developed to verify the accuracy of the model predictions. The presented analyses reveal that existing models may overestimate the shear strength of referenced joints and, therefore, highlight the need for a better fitting model. The discussions include a comparison of predicted joint shear strength values with existing experimental results using three different formulations. Moreover, the discussions examine existing code requirements and the reliability of the presented STM in comparison with code regulations. Concluding remarks supported by statistical measures highlight the fitness of the STM to safely predict the shear strength and identify the optimum approach to determining the model geometry.


  • Seismic performance assessment of fixed offshore structures by endurance time method

    by Mohammad Ali Dastan Diznab, Hamid Mehdigholi, Mohammad Saeed Seif

    The aim of this paper is to consider the ability of endurance time (ET) method to estimate the seismic response of fixed offshore platforms at various excitation levels. In this way, various sources of nonlinear behaviour and challenging issues in the ET approach are included in the three-dimensional model of a real jacket platform utilising the finite element method. In addition to common-designed, over-designed and under-designed cases of this platform have been investigated to examine the effects of the structural characteristics on the ET response. To consider the accuracy and reliability of this approach, results of the ET method are compared with results of nonlinear time history analysis (THA) and response spectrum analysis (RSA) methods at different excitation levels. It is shown that the ET method can predict the seismic performance of the offshore structures with both small computational efforts and reasonable accuracy.