LLLipeng Lu

Lipeng Lu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lipeng Lu has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Evaluation of Compressor Blading With Blade End Slots and Full-Span Slots in a Highly Loaded Compressor Cascade

    by Yumeng Tang, Yangwei Liu, Lipeng Lu

    Blade end slots were proposed to control corner separation in a highly loaded compressor cascade in our previous studies. This study focuses on the evaluation of compressor blading with blade end slots and full-span slots. First, the two-dimensional configuration performance is evaluated both for the datum and slotted profiles. The slotted configuration could effectively suppress separation, especially under positive incidence conditions when the separation is large. Thus, two three-dimensional blading with full-span slots and blade end slots (20% span height from the endwall) are compared. Results show that blading with full-span slots could effectively reduce the loss and enlarge pressure rise under relative high incidence angles, while blading with blade end slots could effectively reduce the loss and enlarge pressure rise above an incidence angle of −4 deg. Blading with slots alters the flow structures and reorganizes the flow in the blade end regions. The self-adaptive jets from the slots reenergize the low-momentum flow downstream and restrain its migration toward the mid-span, so that the corner separation is reduced and the performance is enhanced. The loss for the end slotted blade is lower than that of the full-span slotted blade under incidence angles within 4 deg. This is because the additional mixing loss of the jet and the main flow are caused by the full-span slots at the mid-span regions where the flow remains attached for the blade end slots.


  • Comparison of DDES and URANS for Unsteady Tip Leakage Flow in an Axial Compressor Rotor

    by Yangwei Liu, Luyang Zhong, Li-Peng Lu

    Tip leakage vortex (TLV) has a large impact on compressor performance and should be accurately predicted by computational fluid dynamics (CFD) methods. New approaches of turbulence modeling, such as delayed detached eddy simulation (DDES), have been proposed, the computational resources of which can be reduced much more than for large eddy simulation (LES). In this paper, the numerical simulations of the rotor in a low-speed large-scale axial compressor based on DDES and unsteady Reynolds-averaged Navier–Stokes (URANS) are performed, thus improving our understanding of the TLV dynamic mechanisms and discrepancy of these two methods. We compared the influence of different time steps in the URANS simulation. The widely used large time-step makes the unsteadiness extremely weak. The small time-step shows a better result close to DDES. The time-step scale is related to the URANS unsteadiness and should be carefully selected. In the time-averaged flow, the TLV in DDES dissipates faster, which has a more similar structure to the experiment. Then, the time-averaged and instantaneous results are compared to divide the TLV into three parts. URANS cannot give the loss of stability and evolution details of TLV. The fluctuation velocity spectra show that the amplitude of high frequencies becomes obvious downstream from the TLV, where it becomes unstable. Last, the anisotropy of the Reynolds stress of these two methods is analyzed through the Lumley triangle to see the distinction between the methods and obtain the Reynolds stress. The results indicate that the TLV latter part in DDES is anisotropic, while in URANS it is isotropic.


  • An Exponential Decay Model for the Deterministic Correlations in Axial Compressors

    by Yangwei Liu, Yumeng Tang, Baojie Liu, Lipeng Lu

    The unsteady blade row interaction (UBRI) is inherent and usually has a large effect on performance in multistage axial compressors. The effect could be considered by using the average-passage equation system (APES) in steady-state environment by introducing the deterministic correlations (DC). How to model the DC is the key in APES method. The primary purpose of this study is to develop a DC model for compressor routine design. The APES technique is investigated by using a 3D viscous unsteady and time-averaging Computational fluid dynamics (CFD) flow solver developed in our previous studies. Based on DC characteristics and its effects on time-averaged flow, an exponential decay DC model is proposed and implemented into the developed time-averaging solver. Steady, unsteady, and time-averaging simulations are conducted on the investigation of the UBRI and the DC model in the first transonic stage of NASA 67 and the first two stages of a multistage compressor. The DC distributions and mean flow fields from the DC model are compared with the unsteady simulations. The comparison indicates that the proposed model can take into account the major part of UBRI and provide significant improvements for predicting compressor characteristics and spanwise distributions of flow properties in axial compressors, compared with the steady mixing plane method.


  • Effect of RANS Method on the Stall Onset Prediction by an Eigenvalue Approach

    by Zhe Xie, Yangwei Liu, Xiaohua Liu, Li-Peng Lu, Xiaofeng Sun

    The eigenvalue approach is a recently developed compressor stability model used to predict stall onset. In this model, the flow field from a Reynolds-averaged Navier–Stokes (RANS) simulation provides the basic flow. This paper presents the effect of the RANS methods (including the computational grid, the turbulence model, and the spatial discretization scheme) on the eigenvalue and investigates the most influencing flow structures to the eigenvalue. The test compressor was the transonic compressor of NASA Rotor 37. Three individual meshes with different grid densities were used to validate the grid independence, and the results indicated that RANS simulation and eigenvalue calculation obtain grid independence at the same grid density. Then, the effect of four turbulence models (including Spalart–Allmaras (SA) turbulence model, two different k–ε models with the extended wall function model (EWFKE), and the Yang–Shih model (YSKE), and k–ω shear stress transport (SST) model), and three spatial discretization schemes (the central scheme, the flux difference splitting (FDS) scheme, and the symmetric total variation diminishing (STVD)) was also studied. Further investigation showed that the SA turbulence model combined with the STVD scheme provided the best stall point prediction, with a relative error of 0.05%. Detailed exploration of the three-dimensional flow field revealed that there were two flow patterns near the blade tip necessary for precisely predicting stall onset: the flow blockage generated by the shockwave-tip leakage vortex (TLV) interaction, and the trailing edge separation and corresponding wake flow. The effect of the blockage was greater than the effect of the trailing edge flow.


  • Open Access

    Investigation of Unsteady Flow Interactions in a Transonic High Pressure Turbine Using Nonlinear Harmonic Method

    by Muhammad Afzaal Asghar, Yangwei Liu, Jiahuan Cui, Lipeng Lu

    The performance of a transonic high pressure turbine is mainly influenced by the unsteady interactions associated with the passing blades. In this paper, the unsteady flow interactions in a transonic turbine have been numerically investigated using the nonlinear harmonic (NLH) method in comparison with the steady and unsteady Reynolds-averaged Navier–Stokes (RANS). The comparison shows that the NLH method using three harmonics could capture the main unsteady flow interactions efficiently with about seven times smaller computational cost than the unsteady RANS, resulting in a more accurate time-averaged flow than for steady RANS. However, the continuity of the flow variables across the rotor-stator interface has shown some discrepancies compared with the unsteady RANS, which can be further satisfied by increasing the numbers of harmonics. The unsteady interactions are analyzed in detail; the results show that the wake and trailing edge shock from the upstream stator are the major sources of unsteadiness in the downstream rotor passage. The stator trailing edge shock impinges on the suction side of the passing rotor blades and generates pressure waves. These pressure waves are periodically reflected back to trigger the stator wake shedding. These waves are strong enough to travel through the rotor passage, and eventually affect the flow at the rotor’s trailing edge. The stator wakes are chopped by the downstream rotor, and travel through the rotor passage. This significantly enhances the unsteadiness of the flow near the rotor trailing edge. Lastly, the deterministic stresses and enthalpy distributions extracted from the NLH method have revealed that the effects of the unsteadiness are relatively weaker in the axial direction. Furthermore, the deterministic correlations analysis has shown that, some empirical deterministic correlations models based on the decay concept of compressors are not suitable for turbines.


  • Open Access

    Effect of Slot at Blade Root on Compressor Cascade Performance under Different Aerodynamic Parameters

    by Yangwei Liu, Jinjing Sun, Yumeng Tang, Lipeng Lu

    The effects of compressor aerodynamic parameters, such as pitch-chord ratio, aspect ratio, and fillet, on the cascade performance have been studied in this paper. Slot configuration at the root of the blade has been proved to be an efficient passive control method for the corner separation control in compressor cascade. The combined effects of the pitch-chord ratio, aspect ratio, and blade fillet with a slot configuration on the blade, have also been studied. Larger corner separation caused by the high pitch-chord ratio can be eliminated by the slot, which leads to fewer blades with almost the same or even better cascade performance. Various aspect ratios, together with the slot configuration, have been investigated and all of them have a positive effect on the cascade performance. For the blade with the blade fillet, the slot still has a positive effect on the control of the corner separation, while cascade performance with just a slot configuration is better than the slot configuration under the influence of the blade fillet.


  • Investigation of Vortical Structures and Turbulence Characteristics in Corner Separation in a Linear Compressor Cascade Using DDES

    by Yangwei Liu, Hao Yan, Lipeng Lu, Qiushi Li

    Three-dimensional (3D) corner separation in a linear highly loaded compressor cascade is studied by using delayed detached-eddy simulation (DDES) method. This paper studies the flow mechanism of corner separation, including vortical structures and turbulence characteristics. The vortical structures are analyzed and the distributions of Reynolds stresses and turbulent anisotropy are also discussed in detail. The results show that there exist different kinds of vortical structures, such as horseshoe vortex, passage vortex, wake shedding vortex, and “corner vortex.” Before the corner separation forms, the passage vortex becomes the main secondary vortex and obviously enhances the corner separation. At approximate 35% chord position, the corner vortex begins to form, enlarges rapidly, and dominates the secondary flow in the cascade. The corner vortex is a compound vortex with its vortex core composed of multiple vortices. Streamwise normal Reynolds stress contributes greatest to the turbulence fluctuation in the corner region. The turbulence develops from two-dimensional (2D) turbulence in the near-wall region to one-component type turbulence in the corner region. The turbulence tends to be more anisotropic when the flow is close to the endwall within the corner separation region.


  • Open Access

    Direct Numerical Simulation of Supersonic Turbulent Boundary Layer with Spanwise Wall Oscillation

    by Weidan Ni, Lipeng Lu, Catherine Le Ribault, Jian Fang

    Direct numerical simulations (DNS) of Mach = 2.9 supersonic turbulent boundary layers with spanwise wall oscillation (SWO) are conducted to investigate the turbulent heat transport mechanism and its relation with the turbulent momentum transport. The turbulent coherent structures are suppressed by SWO and the drag is reduced. Although the velocity and temperature statistics are disturbed by SWO differently, the turbulence transports of momentum and heat are simultaneously suppressed. The Reynolds analogy and the strong Reynolds analogy are also preserved in all the controlled flows, proving the consistent mechanisms of momentum transport and heat transport in the turbulent boundary layer with SWO. Despite the extra dissipation and heat induced by SWO, a net wall heat flux reduction can be achieved with the proper selected SWO parameters. The consistent mechanism of momentum and heat transports supports the application of turbulent drag reduction technologies to wall heat flux controls in high-speed vehicles.


  • Open Access

    Corner Separation Control by Boundary Layer Suction Applied to a Highly Loaded Axial Compressor Cascade

    by Yangwei Liu, Jinjing Sun, Lipeng Lu

    Control of corner separation has attracted much interest due to its improvement of performance and energy utilization in turbomachinery. Numerical studies have been performed under both design and off-design flow conditions to investigate the effects of boundary layer suction (BLS) on corner separation in a highly loaded compressor cascade. Two new BLS slot configurations are proposed and a total of five suction slot configurations were studied and compared. Averaged static pressure rise, exit loss coefficient, passage blockage and flow turning angle have been given and compared systematically over a range of operation incidence angles. Distributions of significant loss removal, blade loading, exit deviation and total pressure loss at 3 degree and 7 degree incidence have also been studied. Under the same suction mass flows of 0.7% of the inlet mass flows, the pitchwise suction slot on the endwall shows a better optimal performance over the whole operation incidence among single suction slots. By using of the new proposed compound slot configuration with one spanwise slot on the blade suction side and one pitchwise slot on the endwall, the maximum reduction of total pressure loss at 7 degree incidence can be 39.4%.