ZTZhengjie Tang

Zhengjie Tang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhengjie Tang has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Introduction of aldehyde groups into surface of pine bark via Cannizzaro reaction to improve Urea-formaldehyde resin properties

    by Heng Tian, Linan Zheng, Chenglong Li, Yuanbo Gui, Wenzhuo Zhang, Shaoqiu Zeng, Fanglin Li, Wei Liu, Lianhua Li, Guanchang Wang, et al.


  • Open Access

    Chemical and Enzymatic Fiber Modification to Enhance the Mechanical Properties of CMC Composite Films

    by Xiaobao Li, Zhengjie Tang, Zhenbing Sun, John Simonsen, Zhinan Luo, Xiaoping Li, Jeffery J. Morrell

    Carboxymethyl cellulose (CMC) is a cellulose derivative that can be obtained from wood, bamboo, rattan, straw, and other cellulosic materials. CMC can be used to produce biofilms for many purposes, but the properties of these resulting films make them unsuitable for some applications. The effects of three kinds of plant fiber addition on CMC film properties was investigated using CMC derived from eucalyptus bark cellulose. Tensile strength (TS) and elongation at break (EB) of CMC/sodium alginate/glycerol composite films were 26.2 MPa and 7.35%, respectively. Tensile strength of CMC composite films substantially increased, reaching an optimum at 0.50 g of fiber. The enhancement due to industrial hemp hurd fiber on CMC composite films was more obvious. Pretreatment with hydrogen peroxide (H2O2) and glacial acetic acid (CH3COOH) produced films with a TS of 35.9 MPa and an EB of 1.61%. TS values with pectinase pretreated fiber films was 41.3 MPa and EB was 1.76%. TS of films pretreated with pectinase and hemicellulase was 45.2 MPa and EB was 4.18%. Chemical and enzymatic treatment both improved fiber crystallinity, but film tensile strength was improved to a greater extent by enzymatic treatment. Surface roughness and pyrolysis residue of the film increased after fiber addition, but Fourier transform infrared spectroscopy (FTIR), opacity, and water vapor transmission coefficients were largely unchanged. Adding fiber improved tensile strength of CMC/sodium alginate/glycerol composite films and broadened the application range of CMC composite films without adversely affecting film performance.


  • Open Access

    Antibacterial Films Made of Bacterial Cellulose

    by Zhenbing Sun, Xiaoping Li, Zhengjie Tang, Xiaobao Li, Jeffrey J. Morrell, Johnny Beaugrand, Yao Yao, Qingzhuang Zheng

    Bacterial cellulose (BC) is naturally degradable, highly biocompatible, hydrophilic, and essentially non-toxic, making it potentially useful as a base for creating more sophisticated bio-based materials. BC is similar to plant-derived cellulose in terms of chemical composition and structure but has a number of important differences in microstructure that could provide some unique opportunities for use as a scaffold for other functions. In this study, bacterial cellulose was alkylated and then esterified to produce a carboxymethyl bacterial cellulose (CMBC) that was then used to produce six different composite films with potential antibacterial properties. The films were assessed for antibacterial activity against Staphylococcus aureus and Escherichia coli, pyrolysis characteristics using thermogravimetric analysis (TGA), microstructure using scanning electron microscopy (SEM), and mechanical properties. The addition of nano-silver (nano-Ag) markedly improved the antimicrobial activity of the films while also enhancing the physical and mechanical properties. The results indicate that the three-dimensional reticulated structure of the bacterial cellulose provides an excellent substrate for scaffolding other bioactive materials. Thus, the nano-BC was added into the CMBC/nano-Ag composites furthermore, and then the antibacterial and mechanical properties were improved 44% for E. coli, 59% for S. aureus, and 20% for tensile strength, respectively.


  • Open Access

    The Improved Properties of Carboxymethyl Bacterial Cellulose Films with Thickening and Plasticizing

    by Zhenbing Sun, Zhengjie Tang, Xiaoping Li, Xiaobao Li, Jeffrey J. Morrell, Johnny Beaugrand, Yao Yao, Qingzhuang Zheng

    This study aims to improve the thermal stability and mechanical properties of carboxymethyl bacterial cellulose (CMBC) composite films. Experiments were conducted by preparing bacterial cellulose (BC) into CMBC, then parametrically mixing sodium alginate/starch/xanthan gum/gelatin and glycerin/sorbitol/PEG 400/PEG 6000 with CMBC to form the film. Scanning electron microscopy, X-ray diffractometry, infrared spectroscopy, mechanical tests, and thermogravimetric analysis showed that the composite films had better mechanical properties and thermal stability with the addition of 1.5% CMBC (% v/v), 1% sodium alginate, and 0.4% glycerin. Tensile strength was 38.13 MPa, the elongation at break was 13.4%, the kinematic viscosity of the film solution was 257.3 mm2/s, the opacity was 4.76 A/mm, the water vapor permeability was 11.85%, and the pyrolysis residue was 45%. The potential causes for the differences in the performance of the composite films were discussed and compared, leading to the conclusion that CMBC/Sodium alginate (SA)/glycerin (GL) had the best thermal stability and mechanical properties.


  • Open Access

    Effects of Raw Material Source on the Properties of CMC Composite Films

    by Yao Yao, Zhenbing Sun, Xiaobao Li, Zhengjie Tang, Xiaoping Li, Jeffrey J. Morrell, Yang Liu, Chunli Li, Zhinan Luo

    Sodium carboxymethyl cellulose (CMC) can be derived from a variety of cellulosic materials and is widely used in petroleum mining, construction, paper making, and packaging. CMCs can be derived from many sources with the final properties reflecting the characteristics of the original lignocellulosic matrix as well as the subsequent separation steps that affect the degree of carboxy methyl substitution on the cellulose hydroxyls. While a large percentage of CMCs is derived from wood pulp, many other plant sources may produce more attractive properties for specific applications. The effects of five plant sources on the resulting properties of CMC and CMC/sodium alginate/glycerol composite films were studied. The degree of substitution and resulting tensile strength in leaf-derived CMC was from 0.87 to 0.89 and from 15.81 to 16.35 MPa, respectively, while the degree of substitution and resulting tensile strength in wooden materials-derived CMC were from 1.08 to 1.17 and from 26.08 to 28.97 MPa, respectively. Thus, the degree of substitution and resulting tensile strength tended to be 20% lower in leaf-derived CMCs compared to those prepared from wood or bamboo. Microstructures of bamboo cellulose, bamboo CMC powder, and bamboo leaf CMC composites’ films all differed from pine-derived material, but plant source had no noticeable effect on the X-ray diffraction characteristics, Fourier transform infrared spectroscopy spectra, or pyrolysis properties of CMC or composites films. The results highlighted the potential for using plant source as a tool for varying CMC properties for specific applications.


  • Open Access

    Preparation of Cellulose Nanoparticles from Foliage by Bio-Enzyme Methods

    by Zhengjie Tang, Mingwei Yang, Mingli Qiang, Xiaoping Li, Jeffrey J. Morrell, Yao Yao, Yanwei Su

    There are vast reserves of foliage in nature, which is an inexhaustible precious resource. In this study, the chemical components of five foliage types (pine needles, black locust tree leaves, bamboo leaves, elm leaves and poplar leaves) were analyzed, including cellulose content, hemicellulose content, and lignin content. The bio-enzymatic method was then used to prepare cellulose nanoparticles (CNPs) from these five kinds of leaves, and the prepared CNPs were analyzed using TEM, FTIR, FESEM, and XRD. The results showed that the content of hemicellulose in bamboo leaves was the highest, and the lignin content in the other four leaves was the highest. The cellulose content in the five kinds of foliage was arranged from large to small as pine needles (20.5%), bamboo leaves (19.5%), black locust leaves (18.0%), elm leaves (17.6%), and poplar leaves (15.5%). TEM images showed that the CNPs prepared by the five kinds of foliage reached the nanometer level in width and the micrometer level in length; therefore, the CNPs prepared in this study belonged to cellulose nanofibers (CNFs). The results of FTIR and XRD showed that CNFs prepared by the enzyme treatment exhibited a typical crystalline structure of cellulose II. The degree of crystallinity (DOC) of CNFs prepared from pine needle, poplar leaves, and bamboo leaves are 78.46%, 77.39%, and 81.51%, respectively. FESEM results showed that the CNFs prepared from pine needles, poplar leaves and bamboo leaves by enzymatic method presents a three-dimensional (3D) network structure, and their widths are 31 nm, 36 nm, and 37 nm, respectively. This study provides a meaningful reference for broadening the use of foliage types and improving their added value.


  • Open Access

    Influence of Cellulose Nanoparticles on Rheological Behavior of Oil Well Cement-Water Slurries

    by Zhengjie Tang, Runzhou Huang, Changtong Mei, Xiuxuan Sun, Dingguo Zhou, Xiuqiang Zhang, Qinglin Wu

    Performance of hardened oil well cement (OWC) is largely determined by the rheological properties of the cement slurries. This work was carried out to investigate the effect of water- to-cement ratio (WCR) and cellulose nanoparticles (CNPs), including cellulose nanofibers (CNFs) and cellulose nanocrystals (CNCs), on rheology performance of OWC-based slurries using a Couette rotational viscometer coupled with rheological models. The yield stress and viscosity of neat OWC slurries had a decreasing trend with the increase of WCRs. The suspension became increased unstable with the increase of WCRs. The properties of CNPs, including rheological behaviors, surface properties and morphology, determine the rheological performance of CNP-OWC slurries. In comparison with CNC-OWC slurries, the gel strength, yield stress and viscosity of CNF-OWC slurries were higher as CNFs were more likely to form an entangled network. The gel strength, yield stress and viscosity of CNP-OWC slurries increased with reduced CNF size through regrinding and the proportion of CNFs in the mixture of CNFs and CNCs, respectively.