Zhenbing Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zhenbing Sun has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Jeffrey J. Morrell
Oregon State University
4 shared publications - Xiaobao Li
Yunnan key laboratory of wood adhesives and glue products, Southwest Forestry University, Kunming 650224, China
4 shared publications - Xiaoping Li
Yunnan Provincial Key Laboratory of Wood Adhesives and Glued Products, Southwest Forestry University, Kunming 650224, China
4 shared publications - Zhengjie Tang
Yunnan key laboratory of wood adhesives and glue products, Southwest Forestry University, Kunming 650224, China
4 shared publications - Yao Yao
Yunnan key laboratory of wood adhesives and glue products, Southwest Forestry University, Kunming 650224, China
3 shared publications - Johnny Beaugrand
UR1268 Biopolymères Interactions Assemblages, INRAE, F-44316 Nantes, France
2 shared publications
Latest Publications
- Open Access
The Optimization of the Steam-Heat-Treated Process of Rattan (Calamus simplicifolius) Based on the Response Surface Analysis and Its Chemical Changes
The objective of this study is to investigate the impacts of steam heat treatment parameters (e.g., temperature, time, and pressure) on the impact toughness of rattan (Calamus simplicifolius). The Box–Behnken design response surface analysis was employed to optimize the steam heat treatment parameters. Impact toughness was selected as the evaluation index, with single-factor tests conducted as a baseline for comparison. Changes in chemical composition, cellulose crystallinity, and pyrolysis properties were analyzed using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, Thermogravimetry–Fourier transform infrared (TG-FTIR) spectra, and wet-chemistry methods for both untreated control samples and the heat-treated samples. The results show that a 1 h steam heat treatment at 160 °C under 0.1 MPa pressure has the optimal process parameters for the rattan. The achieved impact toughness value closely matches the predicted value at 71.29 kJ/m2. After the steam heat treatment, hemicellulose and cellulose contents decrease, whereas relative lignin content increases significantly, leading to improved toughness characteristics in Calamus simplicifolius samples. The TG results indicate that maximum weight loss occurs at temperatures of 352 °C, 354 °C, and 361 °C, respectively, for three different samples. This suggests that the thermal stability is enhanced as a result of the heat treatment. These findings will help optimize the heat treatments of the rattan material.
Open AccessThe Optimization of the Steam-Heat-Treated Process of Rattan (Calamus simplicifolius) Based on the Response Surface Analysis and Its Chemical Changes
The objective of this study is to investigate the impacts of steam heat treatment parameters (e.g., temperature, time, and pressure) on the impact toughness of rattan (Calamus simplicifolius). The Box–Behnken design response surface analysis was employed to optimize the steam heat treatment parameters. Impact toughness was selected as the evaluation index, with single-factor tests conducted as a baseline for comparison. Changes in chemical composition, cellulose crystallinity, and pyrolysis properties were analyzed using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, Thermogravimetry–Fourier transform infrared (TG-FTIR) spectra, and wet-chemistry methods for both untreated control samples and the heat-treated samples. The results show that a 1 h steam heat treatment at 160 °C under 0.1 MPa pressure has the optimal process parameters for the rattan. The achieved impact toughness value closely matches the predicted value at 71.29 kJ/m2. After the steam heat treatment, hemicellulose and cellulose contents decrease, whereas relative lignin content increases significantly, leading to improved toughness characteristics in Calamus simplicifolius samples. The TG results indicate that maximum weight loss occurs at temperatures of 352 °C, 354 °C, and 361 °C, respectively, for three different samples. This suggests that the thermal stability is enhanced as a result of the heat treatment. These findings will help optimize the heat treatments of the rattan material.
- Open Access
Chemical and Enzymatic Fiber Modification to Enhance the Mechanical Properties of CMC Composite Films
Carboxymethyl cellulose (CMC) is a cellulose derivative that can be obtained from wood, bamboo, rattan, straw, and other cellulosic materials. CMC can be used to produce biofilms for many purposes, but the properties of these resulting films make them unsuitable for some applications. The effects of three kinds of plant fiber addition on CMC film properties was investigated using CMC derived from eucalyptus bark cellulose. Tensile strength (TS) and elongation at break (EB) of CMC/sodium alginate/glycerol composite films were 26.2 MPa and 7.35%, respectively. Tensile strength of CMC composite films substantially increased, reaching an optimum at 0.50 g of fiber. The enhancement due to industrial hemp hurd fiber on CMC composite films was more obvious. Pretreatment with hydrogen peroxide (H2O2) and glacial acetic acid (CH3COOH) produced films with a TS of 35.9 MPa and an EB of 1.61%. TS values with pectinase pretreated fiber films was 41.3 MPa and EB was 1.76%. TS of films pretreated with pectinase and hemicellulase was 45.2 MPa and EB was 4.18%. Chemical and enzymatic treatment both improved fiber crystallinity, but film tensile strength was improved to a greater extent by enzymatic treatment. Surface roughness and pyrolysis residue of the film increased after fiber addition, but Fourier transform infrared spectroscopy (FTIR), opacity, and water vapor transmission coefficients were largely unchanged. Adding fiber improved tensile strength of CMC/sodium alginate/glycerol composite films and broadened the application range of CMC composite films without adversely affecting film performance.
Open AccessChemical and Enzymatic Fiber Modification to Enhance the Mechanical Properties of CMC Composite Films
Carboxymethyl cellulose (CMC) is a cellulose derivative that can be obtained from wood, bamboo, rattan, straw, and other cellulosic materials. CMC can be used to produce biofilms for many purposes, but the properties of these resulting films make them unsuitable for some applications. The effects of three kinds of plant fiber addition on CMC film properties was investigated using CMC derived from eucalyptus bark cellulose. Tensile strength (TS) and elongation at break (EB) of CMC/sodium alginate/glycerol composite films were 26.2 MPa and 7.35%, respectively. Tensile strength of CMC composite films substantially increased, reaching an optimum at 0.50 g of fiber. The enhancement due to industrial hemp hurd fiber on CMC composite films was more obvious. Pretreatment with hydrogen peroxide (H2O2) and glacial acetic acid (CH3COOH) produced films with a TS of 35.9 MPa and an EB of 1.61%. TS values with pectinase pretreated fiber films was 41.3 MPa and EB was 1.76%. TS of films pretreated with pectinase and hemicellulase was 45.2 MPa and EB was 4.18%. Chemical and enzymatic treatment both improved fiber crystallinity, but film tensile strength was improved to a greater extent by enzymatic treatment. Surface roughness and pyrolysis residue of the film increased after fiber addition, but Fourier transform infrared spectroscopy (FTIR), opacity, and water vapor transmission coefficients were largely unchanged. Adding fiber improved tensile strength of CMC/sodium alginate/glycerol composite films and broadened the application range of CMC composite films without adversely affecting film performance.
- Open Access
Antibacterial Films Made of Bacterial Cellulose
Bacterial cellulose (BC) is naturally degradable, highly biocompatible, hydrophilic, and essentially non-toxic, making it potentially useful as a base for creating more sophisticated bio-based materials. BC is similar to plant-derived cellulose in terms of chemical composition and structure but has a number of important differences in microstructure that could provide some unique opportunities for use as a scaffold for other functions. In this study, bacterial cellulose was alkylated and then esterified to produce a carboxymethyl bacterial cellulose (CMBC) that was then used to produce six different composite films with potential antibacterial properties. The films were assessed for antibacterial activity against Staphylococcus aureus and Escherichia coli, pyrolysis characteristics using thermogravimetric analysis (TGA), microstructure using scanning electron microscopy (SEM), and mechanical properties. The addition of nano-silver (nano-Ag) markedly improved the antimicrobial activity of the films while also enhancing the physical and mechanical properties. The results indicate that the three-dimensional reticulated structure of the bacterial cellulose provides an excellent substrate for scaffolding other bioactive materials. Thus, the nano-BC was added into the CMBC/nano-Ag composites furthermore, and then the antibacterial and mechanical properties were improved 44% for E. coli, 59% for S. aureus, and 20% for tensile strength, respectively.
Open AccessAntibacterial Films Made of Bacterial Cellulose
Bacterial cellulose (BC) is naturally degradable, highly biocompatible, hydrophilic, and essentially non-toxic, making it potentially useful as a base for creating more sophisticated bio-based materials. BC is similar to plant-derived cellulose in terms of chemical composition and structure but has a number of important differences in microstructure that could provide some unique opportunities for use as a scaffold for other functions. In this study, bacterial cellulose was alkylated and then esterified to produce a carboxymethyl bacterial cellulose (CMBC) that was then used to produce six different composite films with potential antibacterial properties. The films were assessed for antibacterial activity against Staphylococcus aureus and Escherichia coli, pyrolysis characteristics using thermogravimetric analysis (TGA), microstructure using scanning electron microscopy (SEM), and mechanical properties. The addition of nano-silver (nano-Ag) markedly improved the antimicrobial activity of the films while also enhancing the physical and mechanical properties. The results indicate that the three-dimensional reticulated structure of the bacterial cellulose provides an excellent substrate for scaffolding other bioactive materials. Thus, the nano-BC was added into the CMBC/nano-Ag composites furthermore, and then the antibacterial and mechanical properties were improved 44% for E. coli, 59% for S. aureus, and 20% for tensile strength, respectively.
- Open Access
The Improved Properties of Carboxymethyl Bacterial Cellulose Films with Thickening and Plasticizing
This study aims to improve the thermal stability and mechanical properties of carboxymethyl bacterial cellulose (CMBC) composite films. Experiments were conducted by preparing bacterial cellulose (BC) into CMBC, then parametrically mixing sodium alginate/starch/xanthan gum/gelatin and glycerin/sorbitol/PEG 400/PEG 6000 with CMBC to form the film. Scanning electron microscopy, X-ray diffractometry, infrared spectroscopy, mechanical tests, and thermogravimetric analysis showed that the composite films had better mechanical properties and thermal stability with the addition of 1.5% CMBC (% v/v), 1% sodium alginate, and 0.4% glycerin. Tensile strength was 38.13 MPa, the elongation at break was 13.4%, the kinematic viscosity of the film solution was 257.3 mm2/s, the opacity was 4.76 A/mm, the water vapor permeability was 11.85%, and the pyrolysis residue was 45%. The potential causes for the differences in the performance of the composite films were discussed and compared, leading to the conclusion that CMBC/Sodium alginate (SA)/glycerin (GL) had the best thermal stability and mechanical properties.
Open AccessThe Improved Properties of Carboxymethyl Bacterial Cellulose Films with Thickening and Plasticizing
This study aims to improve the thermal stability and mechanical properties of carboxymethyl bacterial cellulose (CMBC) composite films. Experiments were conducted by preparing bacterial cellulose (BC) into CMBC, then parametrically mixing sodium alginate/starch/xanthan gum/gelatin and glycerin/sorbitol/PEG 400/PEG 6000 with CMBC to form the film. Scanning electron microscopy, X-ray diffractometry, infrared spectroscopy, mechanical tests, and thermogravimetric analysis showed that the composite films had better mechanical properties and thermal stability with the addition of 1.5% CMBC (% v/v), 1% sodium alginate, and 0.4% glycerin. Tensile strength was 38.13 MPa, the elongation at break was 13.4%, the kinematic viscosity of the film solution was 257.3 mm2/s, the opacity was 4.76 A/mm, the water vapor permeability was 11.85%, and the pyrolysis residue was 45%. The potential causes for the differences in the performance of the composite films were discussed and compared, leading to the conclusion that CMBC/Sodium alginate (SA)/glycerin (GL) had the best thermal stability and mechanical properties.
- Open Access
Effects of Raw Material Source on the Properties of CMC Composite Films
Sodium carboxymethyl cellulose (CMC) can be derived from a variety of cellulosic materials and is widely used in petroleum mining, construction, paper making, and packaging. CMCs can be derived from many sources with the final properties reflecting the characteristics of the original lignocellulosic matrix as well as the subsequent separation steps that affect the degree of carboxy methyl substitution on the cellulose hydroxyls. While a large percentage of CMCs is derived from wood pulp, many other plant sources may produce more attractive properties for specific applications. The effects of five plant sources on the resulting properties of CMC and CMC/sodium alginate/glycerol composite films were studied. The degree of substitution and resulting tensile strength in leaf-derived CMC was from 0.87 to 0.89 and from 15.81 to 16.35 MPa, respectively, while the degree of substitution and resulting tensile strength in wooden materials-derived CMC were from 1.08 to 1.17 and from 26.08 to 28.97 MPa, respectively. Thus, the degree of substitution and resulting tensile strength tended to be 20% lower in leaf-derived CMCs compared to those prepared from wood or bamboo. Microstructures of bamboo cellulose, bamboo CMC powder, and bamboo leaf CMC composites’ films all differed from pine-derived material, but plant source had no noticeable effect on the X-ray diffraction characteristics, Fourier transform infrared spectroscopy spectra, or pyrolysis properties of CMC or composites films. The results highlighted the potential for using plant source as a tool for varying CMC properties for specific applications.
Open AccessEffects of Raw Material Source on the Properties of CMC Composite Films
Sodium carboxymethyl cellulose (CMC) can be derived from a variety of cellulosic materials and is widely used in petroleum mining, construction, paper making, and packaging. CMCs can be derived from many sources with the final properties reflecting the characteristics of the original lignocellulosic matrix as well as the subsequent separation steps that affect the degree of carboxy methyl substitution on the cellulose hydroxyls. While a large percentage of CMCs is derived from wood pulp, many other plant sources may produce more attractive properties for specific applications. The effects of five plant sources on the resulting properties of CMC and CMC/sodium alginate/glycerol composite films were studied. The degree of substitution and resulting tensile strength in leaf-derived CMC was from 0.87 to 0.89 and from 15.81 to 16.35 MPa, respectively, while the degree of substitution and resulting tensile strength in wooden materials-derived CMC were from 1.08 to 1.17 and from 26.08 to 28.97 MPa, respectively. Thus, the degree of substitution and resulting tensile strength tended to be 20% lower in leaf-derived CMCs compared to those prepared from wood or bamboo. Microstructures of bamboo cellulose, bamboo CMC powder, and bamboo leaf CMC composites’ films all differed from pine-derived material, but plant source had no noticeable effect on the X-ray diffraction characteristics, Fourier transform infrared spectroscopy spectra, or pyrolysis properties of CMC or composites films. The results highlighted the potential for using plant source as a tool for varying CMC properties for specific applications.