Agata Sawka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Agata Sawka has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Andrzej Kwatera
AGH University of Science and Technology, Faculty of Materials Science and Ceramics, Al. Mickiewicza 30, 30-059 Kraków, Poland
5 shared publicationsA. Kwatera
4 shared publicationsA. Woźnicki
1 shared publication- Andrzej Kwatera
AGH University of Science and Technology, Faculty of Materials Science and Ceramics, Al. Mickiewicza 30, 30-059 Kraków, Poland
1 shared publication D. Kwatera
1 shared publicationJ. Zasadziński
1 shared publication
Latest Publications
- Open Access
Nanocrystalline Lanthanum Oxide Layers on Tubes Synthesized Using the Metalorganic Chemical Vapor Deposition Technique
Lanthanum oxide (La2O3) layers are widely used in electronics, optics, and optoelectronics due to their properties. Lanthanum oxide is also used as a dopant, modifying and improving the properties of other materials in the form of layers, as well as having a large volume. In this work, lanthanum oxide layers were obtained using MOCVD (Metalorganic Chemical Vapor Deposition) on the inner walls of tubular substrates at 600–750 °C. The basic reactant was La(tmhd)3 (tris(2,2,6,6-tetramethyl-3,5-heptanedionato)lanthanum(III)). The evaporation temperature of La(tmhd)3 amounted to 170–200 °C. Pure argon (99.9999%) and air were used as the carrier gases. The air was also intended to remove the carbon from the synthesized layers. Tubes of quartz glass were used as the substrates. La2O3 layers were found to be growing on their inner surfaces. The value of the extended Grx/Rex2 criterion, where Gr—Grashof’s number, Re—Reynolds’ number, x—the distance from the gas inflow point, was below 0.01. The microstructure of the deposited layers of lanthanum oxide was investigated using an electron scanning microscope (SEM). Their chemical composition was analyzed via energy-dispersive X-ray (EDS) analysis. Their phase composition was tested via X-ray diffraction. The transmittance of the layers of lanthanum oxide was determined with the use of UV-Vis spectroscopy. The obtained layers of lanthanum oxide were characterized by a nanocrystalline microstructure and stable cubic structure. They also exhibited good transparency in both ultraviolet (UV) and visible (Vis) light.
Open AccessNanocrystalline Lanthanum Oxide Layers on Tubes Synthesized Using the Metalorganic Chemical Vapor Deposition Technique
Lanthanum oxide (La2O3) layers are widely used in electronics, optics, and optoelectronics due to their properties. Lanthanum oxide is also used as a dopant, modifying and improving the properties of other materials in the form of layers, as well as having a large volume. In this work, lanthanum oxide layers were obtained using MOCVD (Metalorganic Chemical Vapor Deposition) on the inner walls of tubular substrates at 600–750 °C. The basic reactant was La(tmhd)3 (tris(2,2,6,6-tetramethyl-3,5-heptanedionato)lanthanum(III)). The evaporation temperature of La(tmhd)3 amounted to 170–200 °C. Pure argon (99.9999%) and air were used as the carrier gases. The air was also intended to remove the carbon from the synthesized layers. Tubes of quartz glass were used as the substrates. La2O3 layers were found to be growing on their inner surfaces. The value of the extended Grx/Rex2 criterion, where Gr—Grashof’s number, Re—Reynolds’ number, x—the distance from the gas inflow point, was below 0.01. The microstructure of the deposited layers of lanthanum oxide was investigated using an electron scanning microscope (SEM). Their chemical composition was analyzed via energy-dispersive X-ray (EDS) analysis. Their phase composition was tested via X-ray diffraction. The transmittance of the layers of lanthanum oxide was determined with the use of UV-Vis spectroscopy. The obtained layers of lanthanum oxide were characterized by a nanocrystalline microstructure and stable cubic structure. They also exhibited good transparency in both ultraviolet (UV) and visible (Vis) light.
- Open Access
Chemical Vapour Deposition of Scandia-Stabilised Zirconia Layers on Tubular Substrates at Low Temperatures
The paper presents results of investigation on synthesis of non-porous ZrO2-Sc2O2 layers on tubular substrates by MOCVD (metalorganic chemical vapor deposition) method using Sc(tmhd)3 (Tris(2,2,6,6-tetramethyl-3,5-heptanedionato)scandium(III), 99%) and Zr(tmhd)4 (Tetrakis(2,2,6,6-tetramethyl-3,5-heptanedionato)zirconium)(IV), 99.9+%) as basic reactants. The molar content of Sc(tmhd)3 in the gas mixture was as follows: 14, 28%. The synthesis temperature was in the range of 600–700 °C. The value of extended Grx/Rex2 expression (Gr-Grashof number, Re-Reynolds number and x-the distance from the gas inflow point) was less than 0.01. The layers were deposited under reduced pressure or close to atmospheric pressure. The layers obtained were tested using scanning electron microscope (SEM) with an energy dispersive X-ray spectroscope (EDS) microanalyzer, X-ray diffractometer and UV-Vis spectrophotometer. The layers deposited were non-porous, amorphous or nanocrystalline with controlled chemical composition. The layers synthesized at 700 °C were nanocrystalline. ZrO2-Sc2O3 layers with 14 mol.% Sc2O3 content had a rhombohedral structure.
Open AccessChemical Vapour Deposition of Scandia-Stabilised Zirconia Layers on Tubular Substrates at Low Temperatures
The paper presents results of investigation on synthesis of non-porous ZrO2-Sc2O2 layers on tubular substrates by MOCVD (metalorganic chemical vapor deposition) method using Sc(tmhd)3 (Tris(2,2,6,6-tetramethyl-3,5-heptanedionato)scandium(III), 99%) and Zr(tmhd)4 (Tetrakis(2,2,6,6-tetramethyl-3,5-heptanedionato)zirconium)(IV), 99.9+%) as basic reactants. The molar content of Sc(tmhd)3 in the gas mixture was as follows: 14, 28%. The synthesis temperature was in the range of 600–700 °C. The value of extended Grx/Rex2 expression (Gr-Grashof number, Re-Reynolds number and x-the distance from the gas inflow point) was less than 0.01. The layers were deposited under reduced pressure or close to atmospheric pressure. The layers obtained were tested using scanning electron microscope (SEM) with an energy dispersive X-ray spectroscope (EDS) microanalyzer, X-ray diffractometer and UV-Vis spectrophotometer. The layers deposited were non-porous, amorphous or nanocrystalline with controlled chemical composition. The layers synthesized at 700 °C were nanocrystalline. ZrO2-Sc2O3 layers with 14 mol.% Sc2O3 content had a rhombohedral structure.
- 18 December 2021
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 276, 115580
Low temperature synthesis of Y2O3–doped CeO2 layers using MOCVD
- 18 December 2021
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 276, 115580
Low temperature synthesis of Y2O3–doped CeO2 layers using MOCVD
- Open Access
Deposition of Gadolinia-Doped Zirconia Layers Using Metalorganic Compounds at Low Temperatures
This paper shows the results of an investigation on the synthesis of non-porous and nanocrystalline ZrO2-Gd2O3 layers by metalorganic chemical vapor deposition (MOCVD) with the use of Zr(tmhd)4 (tetrakis(2,2,6,6-tetramethyl-3,5-heptanedionato)zirconium(IV)) and Gd(tmhd)3 (tris(2,2,6,6-tetramethyl-3,5-heptanedionato)gadolinium(III)). Argon and air were used as carrier gases. The molar content of Gd(tmhd)3 in the gas reaction mixture was as follows: 10% and 20%. The layers were synthesized on tubular substrates made of quartz glass at the temperatures of 550–700 °C. Synthesis conditions were established using the Grx/Rex2 expression (Gr is the Grashof number; Re is the Reynolds number; x is the distance from the gas inflow point). The value of this criterion was below 0.01. ZrO2-Gd2O3 layers synthesized at 600–700 °C were crystalline. When the molar content of Gd(tmhd)3 in the gas reaction mixture was 10 mol.%, a relationship between the chemical composition of the gas reaction mixture and that of the deposited layer could be observed. The synthesized layers underwent scanning electron microscopy, as well as X-ray analysis. The transparency of coated and uncoated glass was tested using UV–Vis spectroscopy. Their chemical composition was examined with the use of an EDS analyzer.
Open AccessDeposition of Gadolinia-Doped Zirconia Layers Using Metalorganic Compounds at Low Temperatures
This paper shows the results of an investigation on the synthesis of non-porous and nanocrystalline ZrO2-Gd2O3 layers by metalorganic chemical vapor deposition (MOCVD) with the use of Zr(tmhd)4 (tetrakis(2,2,6,6-tetramethyl-3,5-heptanedionato)zirconium(IV)) and Gd(tmhd)3 (tris(2,2,6,6-tetramethyl-3,5-heptanedionato)gadolinium(III)). Argon and air were used as carrier gases. The molar content of Gd(tmhd)3 in the gas reaction mixture was as follows: 10% and 20%. The layers were synthesized on tubular substrates made of quartz glass at the temperatures of 550–700 °C. Synthesis conditions were established using the Grx/Rex2 expression (Gr is the Grashof number; Re is the Reynolds number; x is the distance from the gas inflow point). The value of this criterion was below 0.01. ZrO2-Gd2O3 layers synthesized at 600–700 °C were crystalline. When the molar content of Gd(tmhd)3 in the gas reaction mixture was 10 mol.%, a relationship between the chemical composition of the gas reaction mixture and that of the deposited layer could be observed. The synthesized layers underwent scanning electron microscopy, as well as X-ray analysis. The transparency of coated and uncoated glass was tested using UV–Vis spectroscopy. Their chemical composition was examined with the use of an EDS analyzer.
- 1 February 2021
- Published by Elsevier in Ceramics International
- Vol. 47 (4) , 5198-5208
Metal-organic chemical vapour deposition of lanthana-doped ceria layers at low temperatures
- 1 February 2021
- Published by Elsevier in Ceramics International
- Vol. 47 (4) , 5198-5208
Metal-organic chemical vapour deposition of lanthana-doped ceria layers at low temperatures
- Open Access
ZrO2-Sm2O3 Layer Growth Using the MOCVD Method at Low Temperatures and Under Reduced Pressure
This work presents the results of structure, microstructure, and chemical composition investigations performed on ZrO2-Sm2O3 layers synthesized by MOCVD (metal-organic chemical vapor deposition) using Zr(tmhd)4 and Sm(tmhd)3 as reactants on quartz glass substrate. The molar percentage of Sm(tmhd)3 used to obtain the layers at both 500 and 550 °C was 14% and 22.75%, respectively. Synthesis parameters were selected so that the value of the extended criterion Grx/Rex2 (Gr—Grashof number, Re—Reynolds number, x—the distance from the gas inflow point to the CVD (MOCVD) reactor) could be maintained below 0.01. It was determined from XRD (X-ray diffraction) analyses that the layers deposited at 500 °C contained small amounts of a crystalline phase and the layers obtained at 550 °C contained greater amounts of the crystalline phase (solid solution). SEM (scanning electron microscope) observations have also shown that the crystalline phase is present in the layers synthesized at 500 °C, as well as at 550 °C. EDS (energy dispersive spectroscopy) studies have indicated that molar content of Sm2O3 in the crystalline phase is lower in comparison to the amount present in the respective amorphous phase. The larger the Sm2O3 content in the layer, the higher the growth rate.
Open AccessZrO2-Sm2O3 Layer Growth Using the MOCVD Method at Low Temperatures and Under Reduced Pressure
This work presents the results of structure, microstructure, and chemical composition investigations performed on ZrO2-Sm2O3 layers synthesized by MOCVD (metal-organic chemical vapor deposition) using Zr(tmhd)4 and Sm(tmhd)3 as reactants on quartz glass substrate. The molar percentage of Sm(tmhd)3 used to obtain the layers at both 500 and 550 °C was 14% and 22.75%, respectively. Synthesis parameters were selected so that the value of the extended criterion Grx/Rex2 (Gr—Grashof number, Re—Reynolds number, x—the distance from the gas inflow point to the CVD (MOCVD) reactor) could be maintained below 0.01. It was determined from XRD (X-ray diffraction) analyses that the layers deposited at 500 °C contained small amounts of a crystalline phase and the layers obtained at 550 °C contained greater amounts of the crystalline phase (solid solution). SEM (scanning electron microscope) observations have also shown that the crystalline phase is present in the layers synthesized at 500 °C, as well as at 550 °C. EDS (energy dispersive spectroscopy) studies have indicated that molar content of Sm2O3 in the crystalline phase is lower in comparison to the amount present in the respective amorphous phase. The larger the Sm2O3 content in the layer, the higher the growth rate.
- 1 April 2018
- Published by Elsevier in Ceramics International
- Vol. 44 (6) , 6257-6264
Deposition of gadolinia-doped ceria layers by MOCVD at low temperatures
- 1 April 2018
- Published by Elsevier in Ceramics International
- Vol. 44 (6) , 6257-6264
Deposition of gadolinia-doped ceria layers by MOCVD at low temperatures
- 1 February 2018
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 228, 142-152
Preparation of ZrO2-Y2O3 layers at low temperatures by MOCVD under atmospheric and reduced pressure
- 1 February 2018
- Published by Elsevier in Materials Science and Engineering: B
- Vol. 228, 142-152
Preparation of ZrO2-Y2O3 layers at low temperatures by MOCVD under atmospheric and reduced pressure
- 1 October 2017
- Published by Elsevier in Materials Letters
- Vol. 204, 39-41
Deposition and characterization of ceria layers using the MOCVD method
- 1 October 2017
- Published by Elsevier in Materials Letters
- Vol. 204, 39-41
Deposition and characterization of ceria layers using the MOCVD method
- 1 May 2016
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 16 (3) , 351-364
Cemented carbide cutting tools life with nanocrystalline Al 2 O 3 layer deposited by MOCVD
- 1 May 2016
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 16 (3) , 351-364
Cemented carbide cutting tools life with nanocrystalline Al 2 O 3 layer deposited by MOCVD