Zong-Lin Li
Zong-Lin Li has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Chien-Ping Lee
Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University, Hsinchu City 30010, Taiwan
4 shared publications - Gray Lin
Institute of Electronics, National Yang Ming Chiao Tung University, Hsinchu City, Taiwan
3 shared publications - Kien Wen Sun
Department of Applied Chemistry, National Yang Ming Chiao Tung University, Hsinchu 300, Taiwan
3 shared publications Chien-Hung Lin
Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University , 1001 University Road, Hsinchu 30010, Taiwan
2 shared publications- Hui-Wen Cheng
Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University, Hsinchu City 30010, Taiwan
2 shared publications - Shen-Chieh Lin
Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University, Hsinchu City 30010, Taiwan
2 shared publications
Latest Publications
- Open Access
- 14 March 2019
- Published by MDPI AG in Micromachines
- Vol. 10 (3) , 188
Effect of Etching Depth on Threshold Characteristics of GaSb-Based Middle Infrared Photonic-Crystal Surface-Emitting Lasers
We study the effect of etching depth on the threshold characteristics of GaSb-based middle infrared (Mid-IR) photonic-crystal surface-emitting lasers (PCSELs) with different lattice periods. The below-threshold emission spectra are measured to identify the bandgap as well as band-edge modes. Moreover, the bandgap separation widens with increasing etching depth as a result of enhanced diffraction feedback coupling. However, the coupling is nearly independent of lattice period. The relationship between threshold gain and Bragg detuning is also experimentally determined for PCSELs and is similar to that calculated theoretically for one-dimensional distributed feedback lasers.
- 14 March 2019
- Published by MDPI AG in Micromachines
- Vol. 10 (3) , 188
Open AccessEffect of Etching Depth on Threshold Characteristics of GaSb-Based Middle Infrared Photonic-Crystal Surface-Emitting Lasers
We study the effect of etching depth on the threshold characteristics of GaSb-based middle infrared (Mid-IR) photonic-crystal surface-emitting lasers (PCSELs) with different lattice periods. The below-threshold emission spectra are measured to identify the bandgap as well as band-edge modes. Moreover, the bandgap separation widens with increasing etching depth as a result of enhanced diffraction feedback coupling. However, the coupling is nearly independent of lattice period. The relationship between threshold gain and Bragg detuning is also experimentally determined for PCSELs and is similar to that calculated theoretically for one-dimensional distributed feedback lasers.
- Open Access
PCSEL Performance of Type-I InGaAsSb Double-QWs Laser Structure Prepared by MBE
This paper discusses the issue of controlling the epitaxial growth of mixed group V alloys to form a type-I InGaAsSb/AlGaAsSb double quantum wells (QWs) structure. We also discuss the run-to-run reproducibility of lattice-matched AlGaAsSb alloys and strained In0.35Ga0.65As0.095Sb0.905 in terms of growth parameters (V/III ratio, Sb2/As2 ratio). Molecular beam epitaxy (MBE) was used to grow two type-I InGaAsSb double-QWs laser structures differing only in the composition of the bottom cladding layer: Al0.85Ga0.15As0.072Sb0.928 (sample A) and Al0.5Ga0.5As0.043Sb0.957 (sample B). Both samples were respectively used in the fabrication of photonic crystal surface-emitting lasers (PCSELs). Sample A presented surface lasing action from circular as well as triangular photonic crystals. Sample B did not present surface lasing due to the deterioration of the active region during the growth of the upper cladding. Our findings underline the importance of temperature in the epitaxial formation of AlxGa1−xAsySb1−y in terms of lasing performance.
Open AccessPCSEL Performance of Type-I InGaAsSb Double-QWs Laser Structure Prepared by MBE
This paper discusses the issue of controlling the epitaxial growth of mixed group V alloys to form a type-I InGaAsSb/AlGaAsSb double quantum wells (QWs) structure. We also discuss the run-to-run reproducibility of lattice-matched AlGaAsSb alloys and strained In0.35Ga0.65As0.095Sb0.905 in terms of growth parameters (V/III ratio, Sb2/As2 ratio). Molecular beam epitaxy (MBE) was used to grow two type-I InGaAsSb double-QWs laser structures differing only in the composition of the bottom cladding layer: Al0.85Ga0.15As0.072Sb0.928 (sample A) and Al0.5Ga0.5As0.043Sb0.957 (sample B). Both samples were respectively used in the fabrication of photonic crystal surface-emitting lasers (PCSELs). Sample A presented surface lasing action from circular as well as triangular photonic crystals. Sample B did not present surface lasing due to the deterioration of the active region during the growth of the upper cladding. Our findings underline the importance of temperature in the epitaxial formation of AlxGa1−xAsySb1−y in terms of lasing performance.
- Open Access
Mid-Infrared Photonic-Crystal Surface-Emitting Lasers with InGaAs/GaAsSb ‘W’-Type Quantum Wells Grown on InP Substrate
InP-based InGaAs/GaAsSb ‘W’-type quantum well (QW) photonic-crystal (PC) surface- emitting lasers (SELs) of 2.2 μm wavelength range are fabricated and room-temperature lasing emissions by optical pumping are demonstrated for the first time. Photonic-crystal surface-emitting laser (PCSEL) devices are investigated in terms of PC parameters of etch depth, lattice period, and filling factor. The lasing emissions cover wavelengths from 2182 nm to 2253 nm. The temperature-dependent lasing characteristics are also studied in terms of lattice period. All PCSELs show consistent lasing wavelength shift against temperature at a rate of 0.17 nm/K. The characteristic temperatures of PCSELs are extracted and discussed with respect to wavelength detuning between QW gain peak and PC cavity resonance.
Open AccessMid-Infrared Photonic-Crystal Surface-Emitting Lasers with InGaAs/GaAsSb ‘W’-Type Quantum Wells Grown on InP Substrate
InP-based InGaAs/GaAsSb ‘W’-type quantum well (QW) photonic-crystal (PC) surface- emitting lasers (SELs) of 2.2 μm wavelength range are fabricated and room-temperature lasing emissions by optical pumping are demonstrated for the first time. Photonic-crystal surface-emitting laser (PCSEL) devices are investigated in terms of PC parameters of etch depth, lattice period, and filling factor. The lasing emissions cover wavelengths from 2182 nm to 2253 nm. The temperature-dependent lasing characteristics are also studied in terms of lattice period. All PCSELs show consistent lasing wavelength shift against temperature at a rate of 0.17 nm/K. The characteristic temperatures of PCSELs are extracted and discussed with respect to wavelength detuning between QW gain peak and PC cavity resonance.
- 2 March 2018
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 123 (9) , 093102
Dual-wavelength GaSb-based mid infrared photonic crystal surface emitting lasers
We demonstrate dual-wavelength GaSb-based mid-infrared photonic crystal surface emitting lasers at room temperature. The two lasing peaks emitted simultaneously at 2.3 μm and 2.22 μm under optical pumping. Type-I InGaAsSb quantum wells were used for the active region. The photonic crystal with a rectangular lattice was fabricated on the surface to provide light coupling for laser operation. The two-wavelength operation was a result of the resonances from the two different grating periods along the two perpendicular directions of the rectangular lattice. The laser emissions from these two wavelengths were highly linearly polarized in two perpendicular directions as a result of the grating design.
- 2 March 2018
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 123 (9) , 093102
Dual-wavelength GaSb-based mid infrared photonic crystal surface emitting lasers
We demonstrate dual-wavelength GaSb-based mid-infrared photonic crystal surface emitting lasers at room temperature. The two lasing peaks emitted simultaneously at 2.3 μm and 2.22 μm under optical pumping. Type-I InGaAsSb quantum wells were used for the active region. The photonic crystal with a rectangular lattice was fabricated on the surface to provide light coupling for laser operation. The two-wavelength operation was a result of the resonances from the two different grating periods along the two perpendicular directions of the rectangular lattice. The laser emissions from these two wavelengths were highly linearly polarized in two perpendicular directions as a result of the grating design.
- 25 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 35 (20) , 4547-4552
Photonic Crystal Surface Emitting Lasers With Quantum Dot Active Region
GaAs-based InAs/InGaAs/GaAs quantum dot (QD) photonic crystal (PC) surface emitting lasers of 1.3 μ m wavelength range are fabricated and room-temperature lasing emissions by optical pumping are demonstrated for the first time. Laser devices are characterized in terms of PC parameters and temperature-dependent measurements are also carried out. The impact of wavelength detuning between PC resonant wavelength and QD gain peak is manifested in the experiments. Moreover, simplified simulation reveals that etched PC depth plays an even more critical role in active region of QD compared to that of quantum well.
- 25 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 35 (20) , 4547-4552
Photonic Crystal Surface Emitting Lasers With Quantum Dot Active Region
GaAs-based InAs/InGaAs/GaAs quantum dot (QD) photonic crystal (PC) surface emitting lasers of 1.3 μ m wavelength range are fabricated and room-temperature lasing emissions by optical pumping are demonstrated for the first time. Laser devices are characterized in terms of PC parameters and temperature-dependent measurements are also carried out. The impact of wavelength detuning between PC resonant wavelength and QD gain peak is manifested in the experiments. Moreover, simplified simulation reveals that etched PC depth plays an even more critical role in active region of QD compared to that of quantum well.
- 1 November 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 306, 92-96
Strain and optical characteristics study of ferromagnetic GaMnAs fabricated by ion beam induced epitaxial crystallization
- 1 November 2016
- Published by Elsevier in Surface and Coatings Technology
- Vol. 306, 92-96
Strain and optical characteristics study of ferromagnetic GaMnAs fabricated by ion beam induced epitaxial crystallization
- 7 October 2013
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 3 (46) , 24126-24131
Carrier dynamics in modulation-doped InAs/GaAs quantum rings
Carrier dynamics in undoped and modulation-doped self-assembled InAs/GaAs quantum rings was comprehensively examined through time-resolved photoluminescence techniques at room temperature. After photoexcitation, the rates of carrier capture and relaxation in the ground state and excited states were equally fast in both the undoped and charged quantum rings. Instead of cascading down through the excited states, the carriers excited in the undoped quantum rings relaxed through the quasi-continuum states via coupling with acoustical phonons and eventually thermalized to the ground state by emitting longitudinal optical phonons. The dynamics of carrier thermalization was governed by cold carriers in the charged quantum rings. In carrier recombination, the undoped quantum rings had a shorter PL decay time and lower luminescence intensity than the charged quantum rings because radiative recombination was suppressed by defects in the matrix and the absence of cold carriers.
- 7 October 2013
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 3 (46) , 24126-24131
Carrier dynamics in modulation-doped InAs/GaAs quantum rings
Carrier dynamics in undoped and modulation-doped self-assembled InAs/GaAs quantum rings was comprehensively examined through time-resolved photoluminescence techniques at room temperature. After photoexcitation, the rates of carrier capture and relaxation in the ground state and excited states were equally fast in both the undoped and charged quantum rings. Instead of cascading down through the excited states, the carriers excited in the undoped quantum rings relaxed through the quasi-continuum states via coupling with acoustical phonons and eventually thermalized to the ground state by emitting longitudinal optical phonons. The dynamics of carrier thermalization was governed by cold carriers in the charged quantum rings. In carrier recombination, the undoped quantum rings had a shorter PL decay time and lower luminescence intensity than the charged quantum rings because radiative recombination was suppressed by defects in the matrix and the absence of cold carriers.
- 12 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 54 (12) , 2733-2740
Averaging and Cancellation Effect of High-Order Nonlinearity of a Power Amplifier
Nonlinear distortion of a power amplifier (PA) due to the nonlinear input-output transfer function is studied. The high-order nonlinearity or Fourier components of the output, due to the mixing of input signals, are found to be related to an average integral related to the transfer function, thus giving insight to the cancellation effect of the nonlinearity. A simple formula has been derived to relate the nth-order Fourier component of a nonlinear transfer function with a sinusoidal input to an average integral of the nth-order derivative of the transfer function. The large signal nonlinear distortion of the nth-order can therefore be regarded as a weighted average of the nth-order derivative of the transfer function. For PAs, the averaging effect gives rise to local minima in the intermodulation distortion terms during power sweep because of the cancellation of the positive part and the negative part of the derivative during averaging. We have applied the formula to InGaP heterojunction bipolar transistors PAs and are able to explain most of the observed nonlinear phenomena of the amplifiers.
- 12 December 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 54 (12) , 2733-2740
Averaging and Cancellation Effect of High-Order Nonlinearity of a Power Amplifier
Nonlinear distortion of a power amplifier (PA) due to the nonlinear input-output transfer function is studied. The high-order nonlinearity or Fourier components of the output, due to the mixing of input signals, are found to be related to an average integral related to the transfer function, thus giving insight to the cancellation effect of the nonlinearity. A simple formula has been derived to relate the nth-order Fourier component of a nonlinear transfer function with a sinusoidal input to an average integral of the nth-order derivative of the transfer function. The large signal nonlinear distortion of the nth-order can therefore be regarded as a weighted average of the nth-order derivative of the transfer function. For PAs, the averaging effect gives rise to local minima in the intermodulation distortion terms during power sweep because of the cancellation of the positive part and the negative part of the derivative during averaging. We have applied the formula to InGaP heterojunction bipolar transistors PAs and are able to explain most of the observed nonlinear phenomena of the amplifiers.