Florian Heilmeier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Florian Heilmeier has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Johannes Roths
Photonics Lab of Munich University of Applied Sciences, Munich, Germany
4 shared publications - Markus Lindner
Photonics Laboratory, Munich University of Applied Sciences, Munich, Germany
4 shared publications - Wolfram Volk
Technische Universität München
4 shared publications Alexander W. Koch
3 shared publicationsKlaus Weraneck
Technical University of Munich
2 shared publicationsMartin Jakobi
2 shared publications
Latest Publications
- Open Access
Evaluation of Strain Transition Properties between Cast-In Fibre Bragg Gratings and Cast Aluminium during Uniaxial Straining
Current testing methods are capable of measuring strain near the surface on structural parts, for example by using strain gauges. However, stress peaks often occur within the material and can only be approximated. An alternative strain measurement incorporates fibre-optical strain sensors (Fiber Bragg Gratings, FBG) which are able to determine strains within the material. The principle has already been verified by using embedded FBGs in tensile specimens. The transition area between fibre and aluminium, however, is not yet properly investigated. Therefore, strains in tensile specimens containing FBGs were measured by neutron diffraction in gauge volumes of two different sizes around the Bragg grating. As a result, it is possible to identify and decouple elastic and plastic strains affecting the FBGs and to transfer the findings into a fully descriptive FE-model of the strain transition area.We thus accomplished closing the gap between the external load and internal straining obtained from cast-in FBG and generating valuable information about the mechanisms within the strain transition area.It was found that the porosity within the casting has a significant impact on the stiffness of the tensile specimen, the generation of excess microscopic tensions and thus the formation of permanent plastic strains, which are well recognized by the FBG. The knowledge that FBG as internal strain sensors function just as well as common external strain sensors will now allow for the application of FBG in actual structural parts and measurements under real load conditions. In the future, applications for long-term monitoring of cast parts will also be enabled and are currently under development.
Open AccessEvaluation of Strain Transition Properties between Cast-In Fibre Bragg Gratings and Cast Aluminium during Uniaxial Straining
Current testing methods are capable of measuring strain near the surface on structural parts, for example by using strain gauges. However, stress peaks often occur within the material and can only be approximated. An alternative strain measurement incorporates fibre-optical strain sensors (Fiber Bragg Gratings, FBG) which are able to determine strains within the material. The principle has already been verified by using embedded FBGs in tensile specimens. The transition area between fibre and aluminium, however, is not yet properly investigated. Therefore, strains in tensile specimens containing FBGs were measured by neutron diffraction in gauge volumes of two different sizes around the Bragg grating. As a result, it is possible to identify and decouple elastic and plastic strains affecting the FBGs and to transfer the findings into a fully descriptive FE-model of the strain transition area.We thus accomplished closing the gap between the external load and internal straining obtained from cast-in FBG and generating valuable information about the mechanisms within the strain transition area.It was found that the porosity within the casting has a significant impact on the stiffness of the tensile specimen, the generation of excess microscopic tensions and thus the formation of permanent plastic strains, which are well recognized by the FBG. The knowledge that FBG as internal strain sensors function just as well as common external strain sensors will now allow for the application of FBG in actual structural parts and measurements under real load conditions. In the future, applications for long-term monitoring of cast parts will also be enabled and are currently under development.
- 26 February 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (5) , 7323-7340
Transition from purely elastic to viscoelastic behavior of silica optical fibers at high temperatures characterized using regenerated Bragg gratings
In this study, the response of regenerated fiber Bragg gratings (RFGBs) to axial forces was investigated in a temperature range from room temperature to 900 °C. For the first time, the transition from pure elastic to viscoelastic behavior around 700 °C of a standard SMF28 optical fiber was measured with an inscribed RFBG. An elastic model with linear temperature dependencies of Young’s modulus and Poisson’s ratio was established, and showed good agreement with the measurements up to temperatures of ∼500 °C. In the temperature range up to 900 °C, the RFBG response could be well described with a simple, single-material approach and a Burgers model that consists of a Kelvin and a Maxwell part. Based on the elastic parameter of the Maxwell part, the temperature-dependent force sensitivity of the RFBG was determined, and it showed a linear decrease in the range from room temperature to ∼500 °C, constant values in the range between ∼500 °C and ∼600 °C, and a strong increase at higher temperatures. While fulfilling the condition to operate in the elastic domain of the silica fiber, the investigations demonstrate that RFBGs can be used as force sensors up to temperatures of ∼600 °C - the range in which temperature-dependent force sensitivities have to be considered. The temperature-dependent parameters of the effective single-material model (elastic and viscoelastic part) are essential to describe the effective mechanical behavior of the optical fiber at high temperatures.
- 26 February 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (5) , 7323-7340
Transition from purely elastic to viscoelastic behavior of silica optical fibers at high temperatures characterized using regenerated Bragg gratings
In this study, the response of regenerated fiber Bragg gratings (RFGBs) to axial forces was investigated in a temperature range from room temperature to 900 °C. For the first time, the transition from pure elastic to viscoelastic behavior around 700 °C of a standard SMF28 optical fiber was measured with an inscribed RFBG. An elastic model with linear temperature dependencies of Young’s modulus and Poisson’s ratio was established, and showed good agreement with the measurements up to temperatures of ∼500 °C. In the temperature range up to 900 °C, the RFBG response could be well described with a simple, single-material approach and a Burgers model that consists of a Kelvin and a Maxwell part. Based on the elastic parameter of the Maxwell part, the temperature-dependent force sensitivity of the RFBG was determined, and it showed a linear decrease in the range from room temperature to ∼500 °C, constant values in the range between ∼500 °C and ∼600 °C, and a strong increase at higher temperatures. While fulfilling the condition to operate in the elastic domain of the silica fiber, the investigations demonstrate that RFBGs can be used as force sensors up to temperatures of ∼600 °C - the range in which temperature-dependent force sensitivities have to be considered. The temperature-dependent parameters of the effective single-material model (elastic and viscoelastic part) are essential to describe the effective mechanical behavior of the optical fiber at high temperatures.
- 18 January 2019
- Published by Springer Nature in Production Engineering
- Vol. 13 (3-4) , 351-360
In-situ strain measurements in the plastic deformation regime inside casted parts using fibre-optical strain sensors
- 18 January 2019
- Published by Springer Nature in Production Engineering
- Vol. 13 (3-4) , 351-360
In-situ strain measurements in the plastic deformation regime inside casted parts using fibre-optical strain sensors
- 16 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 18 (13) , 5352-5360
Regenerated Bragg Grating Sensor Array for Temperature Measurements During an Aluminum Casting Process
An array of regenerated fiber Bragg gratings (RFBGs) was employed to monitor the temperature distribution during an aluminum cast process. Significant temperature gradients in the cast part were observed during the cooling and solidification period. The direction and velocity of the solidification front was revealed by the temperature data obtained by the RFBGs at different measurement points. A generalized calibration curve was established and applied to the RFBG array, avoiding the need of individual calibration measurements of each sensor element of the array. Temperatures measured using the RFBGs and a thermocouple placed in a reference arm of the mold showed excellent agreements and indicated that no thermal drift of the RFBGs sensor elements occurred during the casting. The RFBG measurements were carried out with only a single fiber, which reduced the amount of lead cables in the melt and hence minimized the sensor-induced disturbances to the casting process. In addition, the limited number of cables enables the RFBG sensors to be deployed in small and complex cast geometries. Multipoint temperature sensors based on RFBG arrays can become important tools to improve the quality of casting processes.
- 16 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 18 (13) , 5352-5360
Regenerated Bragg Grating Sensor Array for Temperature Measurements During an Aluminum Casting Process
An array of regenerated fiber Bragg gratings (RFBGs) was employed to monitor the temperature distribution during an aluminum cast process. Significant temperature gradients in the cast part were observed during the cooling and solidification period. The direction and velocity of the solidification front was revealed by the temperature data obtained by the RFBGs at different measurement points. A generalized calibration curve was established and applied to the RFBG array, avoiding the need of individual calibration measurements of each sensor element of the array. Temperatures measured using the RFBGs and a thermocouple placed in a reference arm of the mold showed excellent agreements and indicated that no thermal drift of the RFBGs sensor elements occurred during the casting. The RFBG measurements were carried out with only a single fiber, which reduced the amount of lead cables in the melt and hence minimized the sensor-induced disturbances to the casting process. In addition, the limited number of cables enables the RFBG sensors to be deployed in small and complex cast geometries. Multipoint temperature sensors based on RFBG arrays can become important tools to improve the quality of casting processes.
- Open Access
Strain Measurement in Aluminium Alloy during the Solidification Process Using Embedded Fibre Bragg Gratings
In recent years, the observation of the behaviour of components during the production process and over their life cycle is of increasing importance. Structural health monitoring, for example of carbon composites, is state-of-the-art research. The usage of Fibre Bragg Gratings (FBGs) in this field is of major advantage. Another possible area of application is in foundries. The internal state of melts during the solidification process is of particular interest. By using embedded FBGs, temperature and stress can be monitored during the process. In this work, FBGs were embedded in aluminium alloys in order to observe the occurring strain. Two different FBG positions were chosen in the mould in order to compare its dependence. It was shown that FBGs can withstand the solidification process, although a compression in the range of one percent was measured, which is in agreement with the literature value. Furthermore, different lengths of the gratings were applied, and it was shown that shorter gratings result in more accurate measurements. The obtained results prove that FBGs are applicable as sensors for temperatures up to 740 °C.
Open AccessStrain Measurement in Aluminium Alloy during the Solidification Process Using Embedded Fibre Bragg Gratings
In recent years, the observation of the behaviour of components during the production process and over their life cycle is of increasing importance. Structural health monitoring, for example of carbon composites, is state-of-the-art research. The usage of Fibre Bragg Gratings (FBGs) in this field is of major advantage. Another possible area of application is in foundries. The internal state of melts during the solidification process is of particular interest. By using embedded FBGs, temperature and stress can be monitored during the process. In this work, FBGs were embedded in aluminium alloys in order to observe the occurring strain. Two different FBG positions were chosen in the mould in order to compare its dependence. It was shown that FBGs can withstand the solidification process, although a compression in the range of one percent was measured, which is in agreement with the literature value. Furthermore, different lengths of the gratings were applied, and it was shown that shorter gratings result in more accurate measurements. The obtained results prove that FBGs are applicable as sensors for temperatures up to 740 °C.