Kaushik Choudhury
Kaushik Choudhury has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
Ajai Kumar
2 shared publications- Ajai Kumar
Institute for Plasma Research
2 shared publications Atul Srivastava
2 shared publications- Atul Srivastava
Indian Institute of Technology Bombay
2 shared publications - Michael Owen-Bellini
National Renewable Energy Laboratory
2 shared publications Mukesh Ranjan
2 shared publications
Latest Publications
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Transparent Tedlar® Frontsheet for Lightweight PV Module Designs
The weight of conventional photovoltaic (PV) solar panels is a significant challenge in applications that can benefit from the integration of this renewable energy source, but are sensitive to increased weight loads. Numerous commercial buildings and auxiliary structures are designed with little to no spare structural capacity. Vehicle fuel efficiency is directly tied to the total vehicle weight. Lightweight modules can address this challenge by reducing weight, enabling PV elements to be installed or retrofitted at low cost for parking roofs, in building structures (Building Integrated PV or BIPV), and in vehicles (Vehicle Integrated PV VIPV). The main challenge in acheiving lightweight PV modules is replacing the glass frontsheet while maintaining transparency, mechanical stability and weatherability over the lifetime of the module. Transparent Tedlar® PVF films have been used for decades in protecting graphics and signage and photovoltaic backsheets. Building on years of successful field performance, a new transparent Tedlar® TFS15BM3 film has been designed to provide a high level of outdoor UV stability and protection, offering a significantly lighter technologically advanced alternative to traditional glass. In this paper, we present the performance of this film as a protective frontsheet of solar modules. The unique balance of durability, UV resistance, high level of light transmittance, lasting UV protection, mechanical toughness, chemical resistance, good adhesion to encapsulant, easy cleaning, light weight and flexibility makes this an attractive alternative to traditional glass in applications necessitating lightweight.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Transparent Tedlar® Frontsheet for Lightweight PV Module Designs
The weight of conventional photovoltaic (PV) solar panels is a significant challenge in applications that can benefit from the integration of this renewable energy source, but are sensitive to increased weight loads. Numerous commercial buildings and auxiliary structures are designed with little to no spare structural capacity. Vehicle fuel efficiency is directly tied to the total vehicle weight. Lightweight modules can address this challenge by reducing weight, enabling PV elements to be installed or retrofitted at low cost for parking roofs, in building structures (Building Integrated PV or BIPV), and in vehicles (Vehicle Integrated PV VIPV). The main challenge in acheiving lightweight PV modules is replacing the glass frontsheet while maintaining transparency, mechanical stability and weatherability over the lifetime of the module. Transparent Tedlar® PVF films have been used for decades in protecting graphics and signage and photovoltaic backsheets. Building on years of successful field performance, a new transparent Tedlar® TFS15BM3 film has been designed to provide a high level of outdoor UV stability and protection, offering a significantly lighter technologically advanced alternative to traditional glass. In this paper, we present the performance of this film as a protective frontsheet of solar modules. The unique balance of durability, UV resistance, high level of light transmittance, lasting UV protection, mechanical toughness, chemical resistance, good adhesion to encapsulant, easy cleaning, light weight and flexibility makes this an attractive alternative to traditional glass in applications necessitating lightweight.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Evaluation of Beta-Phase Formation in the Failure of PVDF-Based Solar Module Backsheets
There are concerns about the potential for polyvinylidene fluoride (PVDF)-based backsheets to crack and fail prematurely. Several studies have suggested that polymer phase change may play a role in the failure mechanism. Here we utilize wide-angle X-ray scattering maps to show that alpha- to beta-phase transformations occurs at cracks tips in aged PVDF-based backsheets. In addition, our work demonstrates that beta-phase formation is not required for crack growth and only occurs at crack tips when plastic deformation of the PVDF polymer has occurred.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Evaluation of Beta-Phase Formation in the Failure of PVDF-Based Solar Module Backsheets
There are concerns about the potential for polyvinylidene fluoride (PVDF)-based backsheets to crack and fail prematurely. Several studies have suggested that polymer phase change may play a role in the failure mechanism. Here we utilize wide-angle X-ray scattering maps to show that alpha- to beta-phase transformations occurs at cracks tips in aged PVDF-based backsheets. In addition, our work demonstrates that beta-phase formation is not required for crack growth and only occurs at crack tips when plastic deformation of the PVDF polymer has occurred.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Mapping Stress in PV Modules: The Influence of Soldering, Tabbing, and Module Architecture
Alternatives to conventional photovoltaic cell tabbing schemes are explored for their promising electrical properties and low cost. When implementing new architectures and bill of materials very little attention is usually paid to the thermomechanical stresses acting on the cell. To this point, even less is understood about the effect these stresses have on failure modes and module lifetime. Here, we use X-ray Topography to image in-situ the stresses in cells with conventional and multi-busbar tabbing with different bill of materials and configurations (glass/glass vs. glass backsheet). We determine that, while residual stresses are reduced with multi bus bar tabbing in glass-backsheet laminates, glass-glass laminates require significantly thicker encapsulant to achieve similar stress levels. At the time of presentation we will complete the set with interdigitated back contact cells and POE vs. EVA.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Mapping Stress in PV Modules: The Influence of Soldering, Tabbing, and Module Architecture
Alternatives to conventional photovoltaic cell tabbing schemes are explored for their promising electrical properties and low cost. When implementing new architectures and bill of materials very little attention is usually paid to the thermomechanical stresses acting on the cell. To this point, even less is understood about the effect these stresses have on failure modes and module lifetime. Here, we use X-ray Topography to image in-situ the stresses in cells with conventional and multi-busbar tabbing with different bill of materials and configurations (glass/glass vs. glass backsheet). We determine that, while residual stresses are reduced with multi bus bar tabbing in glass-backsheet laminates, glass-glass laminates require significantly thicker encapsulant to achieve similar stress levels. At the time of presentation we will complete the set with interdigitated back contact cells and POE vs. EVA.
- 1 June 2021
- Published by Elsevier in Current Opinion in Biomedical Engineering
- Vol. 18
A perspective on implantable biomedical materials and devices for diagnostic applications
- 1 June 2021
- Published by Elsevier in Current Opinion in Biomedical Engineering
- Vol. 18
A perspective on implantable biomedical materials and devices for diagnostic applications
- 1 February 2019
- Published by Elsevier in Nano-Structures & Nano-Objects
- Vol. 17, 129-137
Effect of confined geometry on the size distribution of nanoparticles produced by laser ablation in liquid medium
- 1 February 2019
- Published by Elsevier in Nano-Structures & Nano-Objects
- Vol. 17, 129-137
Effect of confined geometry on the size distribution of nanoparticles produced by laser ablation in liquid medium
- 1 January 2019
- Published by Elsevier
- p. 279-313
Combined and Sequential Accelerated Stress Testing for Derisking Photovoltaic Modules
- 1 January 2019
- Published by Elsevier
- p. 279-313
Combined and Sequential Accelerated Stress Testing for Derisking Photovoltaic Modules
- 1 December 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 41
A novel method for fabrication of size-controlled metallic nanoparticles by laser ablation
- 1 December 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 41
A novel method for fabrication of size-controlled metallic nanoparticles by laser ablation
- 2 May 2017
- Published by Springer Nature in Applied Physics B
- Vol. 123 (5) , 163
Time-resolved whole field investigation of plasma plume-induced shock wave in liquid media of different densities
- 2 May 2017
- Published by Springer Nature in Applied Physics B
- Vol. 123 (5) , 163
Time-resolved whole field investigation of plasma plume-induced shock wave in liquid media of different densities
- 1 April 2016
- Published by AIP Publishing in Physics of Plasmas
- Vol. 23 (4) , 042108
Time resolved interferometric study of the plasma plume induced shock wave in confined geometry: Two-dimensional mapping of the ambient and plasma density
An experimental investigation of the laser produced plasma induced shock wave in the presence of confining walls placed along the axial as well as the lateral direction has been performed. A time resolved Mach Zehnder interferometer is set up to track the primary as well as the reflected shock waves and its effect on the evolving plasma plume has been studied. An attempt has been made to discriminate the electronic and medium density contributions towards the changes in the refractive index of the medium. Two dimensional spatial distributions for both ambient medium density and plasma density (electron density) have been obtained by employing customised inversion technique and algorithm on the recorded interferograms. The observed density pattern of the surrounding medium in the presence of confining walls is correlated with the reflected shock wave propagation in the medium. Further, the shock wave plasma interaction and the subsequent changes in the shape and density of the plasma plume in confined geometry are briefly described.
- 1 April 2016
- Published by AIP Publishing in Physics of Plasmas
- Vol. 23 (4) , 042108
Time resolved interferometric study of the plasma plume induced shock wave in confined geometry: Two-dimensional mapping of the ambient and plasma density
An experimental investigation of the laser produced plasma induced shock wave in the presence of confining walls placed along the axial as well as the lateral direction has been performed. A time resolved Mach Zehnder interferometer is set up to track the primary as well as the reflected shock waves and its effect on the evolving plasma plume has been studied. An attempt has been made to discriminate the electronic and medium density contributions towards the changes in the refractive index of the medium. Two dimensional spatial distributions for both ambient medium density and plasma density (electron density) have been obtained by employing customised inversion technique and algorithm on the recorded interferograms. The observed density pattern of the surrounding medium in the presence of confining walls is correlated with the reflected shock wave propagation in the medium. Further, the shock wave plasma interaction and the subsequent changes in the shape and density of the plasma plume in confined geometry are briefly described.
- 1 June 2011
- Published by Elsevier in Materials Letters
- Vol. 65 (11) , 1625-1627
Lattice expansion in ZnSe quantum dots
- 1 June 2011
- Published by Elsevier in Materials Letters
- Vol. 65 (11) , 1625-1627
Lattice expansion in ZnSe quantum dots