Asok Kumar Barua
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Asok Kumar Barua has a total of 182 co-authors. Here are the top co-authors by number of shared publications:
Swati Ray
44 shared publicationsRatnabali Banerjee
25 shared publicationsA. K. Batabyal
Energy Research Unit, Indian Association for the Cultivation of Science , Jadavpur, Calcutta , 700 032 , India
17 shared publications- Sourav Mandal
Indian Institute of Technology Delhi
17 shared publications Debajyoti Das
13 shared publicationsS Saha
12 shared publications
Latest Publications
- 1 February 2019
- Published by Springer Nature
- p. 361-366
Application of N-doped ZnO Nanorods in Heterojunction Si Solar Cells
- 1 February 2019
- Published by Springer Nature
- p. 361-366
Application of N-doped ZnO Nanorods in Heterojunction Si Solar Cells
- 3 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (1) , 18-25
Mixed-Phase nc-SiOX:H Interlayer to Improve Light Trapping and Shunt Quenching in a-Si:H Solar Cell
By using radio frequency plasma enhanced chemical vapor deposition method (13.56 MHz), a mixed phase nanocrystalline silicon oxide (nc-SiOX:H) interlayer has been developed. The optoelectronic properties of the nc-SiO:H layer was optimized by varying gas flow ratio. An interlayer has been inserted between the silicon layer and back contact. The nc-SiO:H interlayer has served as a dual-function layer in the solar cell, i.e., act as a rear reflector layer for light trapping and also minimized the local leakage and quenching the shunt effect. The fabricated solar cells with and without nc-SiOX:H interlayer showed efficiencies of 7.84% and 9.35%, respectively, with an i-layer thickness of 250 nm. Efficient light trapping and suppressed parasitic losses by adopting nc-SiOX:H interlayer resulted in a relative increase in the efficiency of about 19.26%. Light-induced degradation study of the solar cells with and without an interlayer has also been presented here. After shunt quenching effect, the relative degradation in conversion efficiency for an interlayer cell is ~7.27% after 1000 h of light soaking, whereas, under the same experimental conditions, the relative degradation is ~10.82% for the solar cell without an interlayer. The possible origin of higher degradation in the latter device has been addressed in this work.
- 3 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (1) , 18-25
Mixed-Phase nc-SiOX:H Interlayer to Improve Light Trapping and Shunt Quenching in a-Si:H Solar Cell
By using radio frequency plasma enhanced chemical vapor deposition method (13.56 MHz), a mixed phase nanocrystalline silicon oxide (nc-SiOX:H) interlayer has been developed. The optoelectronic properties of the nc-SiO:H layer was optimized by varying gas flow ratio. An interlayer has been inserted between the silicon layer and back contact. The nc-SiO:H interlayer has served as a dual-function layer in the solar cell, i.e., act as a rear reflector layer for light trapping and also minimized the local leakage and quenching the shunt effect. The fabricated solar cells with and without nc-SiOX:H interlayer showed efficiencies of 7.84% and 9.35%, respectively, with an i-layer thickness of 250 nm. Efficient light trapping and suppressed parasitic losses by adopting nc-SiOX:H interlayer resulted in a relative increase in the efficiency of about 19.26%. Light-induced degradation study of the solar cells with and without an interlayer has also been presented here. After shunt quenching effect, the relative degradation in conversion efficiency for an interlayer cell is ~7.27% after 1000 h of light soaking, whereas, under the same experimental conditions, the relative degradation is ~10.82% for the solar cell without an interlayer. The possible origin of higher degradation in the latter device has been addressed in this work.
- 22 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (1) , 8-15
Reduction of Hole Injection Barrier Height at TCO/P Interface Using a-SiO:H Interlayer
In a thin film, p-i-n solar cell the front contact interface loss due to high band bending between TCO front contact and p-type window layer can be minimized by inserting a wind band gap hydrogenated amorphous silicon oxide interlayer at the TCO/p interface. In this paper, a simulation and experimental investigation on the performance of p-i-n solar cell by inserting the intrinsic hydrogenated amorphous silicon oxide (i-a-SiO:H) at the TCO/p interface has been carried out. A device quality wide bandgap i-a-SiO:H interlayer was prepared at 230 °C substrate temperature by using radio frequency plasma-enhanced chemical vapor deposition (13.56 MHz RF-PECVD) technique. The experimental results in this study showed that the integration of interlayer at the TCO/p interface reduces the barrier height from 0.513 to 0.472 eV resulting the power conversion efficiency (η) of 9.38% and fill factor (FF) of 74.8% for a single-junction p-i-n solar cell with an active area of 1.0 cm2. In addition, the electrically and optically calibrated simulations also confirm that the application of interlayer at the TCO/p interface reduces the barrier height. As a result, the electric filed over the frontal region has decreased, which aided to minimize the recombination of photogenerated holes with back diffusing electrons at the front contact. The spectral response of the solar cell with interlayer has also improved significantly in the lower wavelength region (350–600 nm) in comparison to the cell without an interlayer at the TCO/p interface.
- 22 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 8 (1) , 8-15
Reduction of Hole Injection Barrier Height at TCO/P Interface Using a-SiO:H Interlayer
In a thin film, p-i-n solar cell the front contact interface loss due to high band bending between TCO front contact and p-type window layer can be minimized by inserting a wind band gap hydrogenated amorphous silicon oxide interlayer at the TCO/p interface. In this paper, a simulation and experimental investigation on the performance of p-i-n solar cell by inserting the intrinsic hydrogenated amorphous silicon oxide (i-a-SiO:H) at the TCO/p interface has been carried out. A device quality wide bandgap i-a-SiO:H interlayer was prepared at 230 °C substrate temperature by using radio frequency plasma-enhanced chemical vapor deposition (13.56 MHz RF-PECVD) technique. The experimental results in this study showed that the integration of interlayer at the TCO/p interface reduces the barrier height from 0.513 to 0.472 eV resulting the power conversion efficiency (η) of 9.38% and fill factor (FF) of 74.8% for a single-junction p-i-n solar cell with an active area of 1.0 cm2. In addition, the electrically and optically calibrated simulations also confirm that the application of interlayer at the TCO/p interface reduces the barrier height. As a result, the electric filed over the frontal region has decreased, which aided to minimize the recombination of photogenerated holes with back diffusing electrons at the front contact. The spectral response of the solar cell with interlayer has also improved significantly in the lower wavelength region (350–600 nm) in comparison to the cell without an interlayer at the TCO/p interface.
- 16 November 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 29 (4) , 3210-3218
Optimization of the texturization of ZnO:Al surface using HCl + HNO3 for application in thin film silicon solar cells
- 16 November 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 29 (4) , 3210-3218
Optimization of the texturization of ZnO:Al surface using HCl + HNO3 for application in thin film silicon solar cells
- 1 August 2017
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 66, 9-14
Role of dual SiO x : H based buffer at the p/i interface on the performance of single junction microcrystalline solar cells
- 1 August 2017
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 66, 9-14
Role of dual SiO x : H based buffer at the p/i interface on the performance of single junction microcrystalline solar cells
- 20 July 2017
- Published by Springer Nature in Journal of Materials Science
- Vol. 52 (21) , 12818-12825
Blue and violet defect levels mediated absorption hot spots in tapered ZnO nanorods toward improved photocatalytic activity
- 20 July 2017
- Published by Springer Nature in Journal of Materials Science
- Vol. 52 (21) , 12818-12825
Blue and violet defect levels mediated absorption hot spots in tapered ZnO nanorods toward improved photocatalytic activity
- 13 July 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 28 (21) , 16165-16172
Effect of oxide based graded buffer and bottom n-layer on the performance of the single junction amorphous silicon solar cells
- 13 July 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 28 (21) , 16165-16172
Effect of oxide based graded buffer and bottom n-layer on the performance of the single junction amorphous silicon solar cells
- 27 March 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 28 (14) , 10382-10390
Influence of excitation frequency and electrode separation on the growth of microcrystalline silicon films and their application in single junction microcrystalline solar cell
- 27 March 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 28 (14) , 10382-10390
Influence of excitation frequency and electrode separation on the growth of microcrystalline silicon films and their application in single junction microcrystalline solar cell
- 13 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 7 (3) , 892-899
Development of Improved n-μc-SiO$_x$ :H Films and Its Innovative Application in Silicon-Based Single Junction Thin Film Solar Cells
In this paper, we have discussed about the development of high-quality n-μc-SiO:H films by a seeding technique working as a potential back reflector layer (BRL). Highly crystalline and conducting n-μc-Si:H films are used as a seed layer. Phosphorous-doped SiOx:H film with suitable optoelectronics properties has been deposited by a radio frequency plasma enhanced chemical vapor deposition technique using parallel plate reactors (capacititively coupled). Optoelectronics properties have been controlled and optimized varying the deposition parameters such as process pressure, power density, partial pressure of CO2, etc. We have also innovatively replaced the n-layer, i.e., n-a-Si:H in case of the a-Si:H cell and n-μc-Si:H for μc-Si:H cells by this optimized seed + n-μc-SiO:H films. The performance of this n-μcSiO:H film grown on the n-μc-Si:H seed layer as n-layer as well as BRL of single junction a-Si:H and μc-Si:H solar cells has been evaluated and better Photovoltaic (PV) characteristics of the solar cell are realized as compared to those of the films developed without any seed layer. a-Si:H solar cells with initial efficiency of 9.38% and μc-Si:H solar cell of 8.50% have been successfully fabricated by using improved doped SiOx:H based BRL replacing conventional n-layer of the single junction cells.
- 13 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 7 (3) , 892-899
Development of Improved n-μc-SiO$_x$ :H Films and Its Innovative Application in Silicon-Based Single Junction Thin Film Solar Cells
In this paper, we have discussed about the development of high-quality n-μc-SiO:H films by a seeding technique working as a potential back reflector layer (BRL). Highly crystalline and conducting n-μc-Si:H films are used as a seed layer. Phosphorous-doped SiOx:H film with suitable optoelectronics properties has been deposited by a radio frequency plasma enhanced chemical vapor deposition technique using parallel plate reactors (capacititively coupled). Optoelectronics properties have been controlled and optimized varying the deposition parameters such as process pressure, power density, partial pressure of CO2, etc. We have also innovatively replaced the n-layer, i.e., n-a-Si:H in case of the a-Si:H cell and n-μc-Si:H for μc-Si:H cells by this optimized seed + n-μc-SiO:H films. The performance of this n-μcSiO:H film grown on the n-μc-Si:H seed layer as n-layer as well as BRL of single junction a-Si:H and μc-Si:H solar cells has been evaluated and better Photovoltaic (PV) characteristics of the solar cell are realized as compared to those of the films developed without any seed layer. a-Si:H solar cells with initial efficiency of 9.38% and μc-Si:H solar cell of 8.50% have been successfully fabricated by using improved doped SiOx:H based BRL replacing conventional n-layer of the single junction cells.