Wei Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Wei Zhou has a total of 108 co-authors. Here are the top co-authors by number of shared publications:
- Ruikun Mai
Tongji University
35 shared publications - Zhengyou He
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
18 shared publications - Zhaotian Yan
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
9 shared publications - Dingyuan Tang
Southwest Jiaotong University
7 shared publications - Lizhou Liu
College of Electrical Engineering, Sichuan University, Chengdu, China
6 shared publications Qiang Zhang
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
5 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (10) , 14325-14336
Transmission Line Effect of Dynamic Capacitive Power Transfer System and Its Suppression Method Based on Switchable Terminal Reactance
In dynamic wireless power transfer systems, long segmented transmitter couplers facilitate simplified control and mitigate voltage fluctuations. However, dynamic capacitive power transfer (CPT) systems typically operate in the MHz range, where the high-frequency excitation wavelength is comparable to the dimensions of long segmented transmitter plates. This induces significant transmission line effects (TLE) in the system couplers, resulting severe electric-field inhomogeneity and even near-zero-field regions. These issues severely constrain the system’s power transfer capacity and stability. This article develops a mathematical model for dynamic CPT systems accounting for the TLE in long segmented transmitter plates, and analyzes the electric-field distribution around transmitter plates as well as the receiver output characteristics. It also proposes an open-loop output voltage fluctuation suppression method based on switchable terminal reactance, along with a corresponding terminal reactance parameters optimization method and switching strategy. Integrated with the transmitter’s DC–DC converter, it enables closed-loop control of output voltage. An experimental prototype was built with an operating frequency of 6.78 MHz, 10 m-long transmitter plates, and a system power of 30 W. Experimental results demonstrate distinct near-zero-power operation intervals in the output voltage without terminal reactance, with the voltage fluctuation rate approaching nearly 100%. Adopting the proposed method reduces the open-loop output voltage fluctuation rate to 30.1%, and implementing closed-loop control further decreases it to within 5%. The fluctuation trends and amplitudes of the system output voltage before and after using the proposed method are consistent with theoretical values, verifying that the proposed method realizes stable constant-voltage output across all segments of dynamic CPT systems.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (10) , 14325-14336
Transmission Line Effect of Dynamic Capacitive Power Transfer System and Its Suppression Method Based on Switchable Terminal Reactance
In dynamic wireless power transfer systems, long segmented transmitter couplers facilitate simplified control and mitigate voltage fluctuations. However, dynamic capacitive power transfer (CPT) systems typically operate in the MHz range, where the high-frequency excitation wavelength is comparable to the dimensions of long segmented transmitter plates. This induces significant transmission line effects (TLE) in the system couplers, resulting severe electric-field inhomogeneity and even near-zero-field regions. These issues severely constrain the system’s power transfer capacity and stability. This article develops a mathematical model for dynamic CPT systems accounting for the TLE in long segmented transmitter plates, and analyzes the electric-field distribution around transmitter plates as well as the receiver output characteristics. It also proposes an open-loop output voltage fluctuation suppression method based on switchable terminal reactance, along with a corresponding terminal reactance parameters optimization method and switching strategy. Integrated with the transmitter’s DC–DC converter, it enables closed-loop control of output voltage. An experimental prototype was built with an operating frequency of 6.78 MHz, 10 m-long transmitter plates, and a system power of 30 W. Experimental results demonstrate distinct near-zero-power operation intervals in the output voltage without terminal reactance, with the voltage fluctuation rate approaching nearly 100%. Adopting the proposed method reduces the open-loop output voltage fluctuation rate to 30.1%, and implementing closed-loop control further decreases it to within 5%. The fluctuation trends and amplitudes of the system output voltage before and after using the proposed method are consistent with theoretical values, verifying that the proposed method realizes stable constant-voltage output across all segments of dynamic CPT systems.
- 15 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Coupled Resonant Inductor Based Interleaved Two-Phase SCLLC Converter with Auto Current Sharing and Ripple Reduction
The passive current sharing methods with coupled inductors for multiphase LLC converters typically cannot achieve interleaving operation, leading to high current ripple. To solve this problem, a coupled resonant inductor (CRI)-based topology is proposed with auto current sharing and interleaved operation. The proposed CRI topology is based on the switched-capacitor LLC converter (SCLLC), where the resonant inductors are moved out of the resonant tank and then combined into a coupled inductor. The improved coupled inductor method allows interleaving operation, achieving excellent current ripple cancellation effect while realizing auto current sharing. Besides, the partial power processing capability inherited from SCLLC reduces the losses in the coupled inductor. A 300W experimental prototype demonstrate that the current sharing error is within 4% across the load range of 5~25A. Besides, the prototype achieves a 56% reduction in output current ripple compared to a non-coupled implementation. Finally, the proposed topology maintains excellent efficiency performance (>96%) across the load range (5~25A), with a peak efficiency up to 97.5%.
- 15 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Coupled Resonant Inductor Based Interleaved Two-Phase SCLLC Converter with Auto Current Sharing and Ripple Reduction
The passive current sharing methods with coupled inductors for multiphase LLC converters typically cannot achieve interleaving operation, leading to high current ripple. To solve this problem, a coupled resonant inductor (CRI)-based topology is proposed with auto current sharing and interleaved operation. The proposed CRI topology is based on the switched-capacitor LLC converter (SCLLC), where the resonant inductors are moved out of the resonant tank and then combined into a coupled inductor. The improved coupled inductor method allows interleaving operation, achieving excellent current ripple cancellation effect while realizing auto current sharing. Besides, the partial power processing capability inherited from SCLLC reduces the losses in the coupled inductor. A 300W experimental prototype demonstrate that the current sharing error is within 4% across the load range of 5~25A. Besides, the prototype achieves a 56% reduction in output current ripple compared to a non-coupled implementation. Finally, the proposed topology maintains excellent efficiency performance (>96%) across the load range (5~25A), with a peak efficiency up to 97.5%.
- 5 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (3) , 3908-3919
A Magnetic-Integrated Hybrid Topology for Capacitive Power Transfer System Achieving Antimisalignment and Inductor Miniaturization
For capacitive power transfer (CPT) systems, antimisalignment capability and receiver miniaturization remain critical challenges in practice, especially for modular CPT systems. This article proposes a magnetic integrated hybrid topology to address output fluctuations under misalignment and load variation conditions, while reducing receiver volume. First, a diagonal-plate four-port capacitive coupler is designed to form two independent capacitive coupling channels. Then, a hybrid compensation topology using magnetically integrated inductors (MIIs) is proposed for these two channels. The two channels with the hybrid topology exhibit complementary gain characteristics, enabling the CPT system to maintain constant output against alignment and load disturbances. Meanwhile, all receiver-side inductors are integrated on a pair of toroidal cores for miniaturization. Finally, a 1 kW experimental prototype is constructed, and the results show that the output voltage fluctuates within 10% when the coupler is misaligned within $\boldsymbol{\pm}$80 mm (x-direction), $\boldsymbol{\pm}$60$\surd{}$2 mm (x/y bisector), and $\boldsymbol{-}$5 to 9 mm (z-direction). The output voltage increase is not exceeded 18% as the load varies from 20 to 100 $\boldsymbol{\Omega}$. Additionally, the proposed MIIs reduces the volume of receiver-side inductors by 85.85% compared to the conventional three air-core inductor configuration.
- 5 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (3) , 3908-3919
A Magnetic-Integrated Hybrid Topology for Capacitive Power Transfer System Achieving Antimisalignment and Inductor Miniaturization
For capacitive power transfer (CPT) systems, antimisalignment capability and receiver miniaturization remain critical challenges in practice, especially for modular CPT systems. This article proposes a magnetic integrated hybrid topology to address output fluctuations under misalignment and load variation conditions, while reducing receiver volume. First, a diagonal-plate four-port capacitive coupler is designed to form two independent capacitive coupling channels. Then, a hybrid compensation topology using magnetically integrated inductors (MIIs) is proposed for these two channels. The two channels with the hybrid topology exhibit complementary gain characteristics, enabling the CPT system to maintain constant output against alignment and load disturbances. Meanwhile, all receiver-side inductors are integrated on a pair of toroidal cores for miniaturization. Finally, a 1 kW experimental prototype is constructed, and the results show that the output voltage fluctuates within 10% when the coupler is misaligned within $\boldsymbol{\pm}$80 mm (x-direction), $\boldsymbol{\pm}$60$\surd{}$2 mm (x/y bisector), and $\boldsymbol{-}$5 to 9 mm (z-direction). The output voltage increase is not exceeded 18% as the load varies from 20 to 100 $\boldsymbol{\Omega}$. Additionally, the proposed MIIs reduces the volume of receiver-side inductors by 85.85% compared to the conventional three air-core inductor configuration.
- 10 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (2) , 1646-1651
A Single-Switch and Parameter-Insensitive Capacitive Power Transfer System for Biomedical Implants
This letter proposes a nonresonant capacitive power transfer system for active biomedical implants that eliminates resonance dependency while maintaining physical isolation. By leveraging biological tissue as the dielectric medium in a four-plate coupler and drawing inspiration from Zeta converter topology, the system achieves parameter insensitivity and single-switch control. Theoretical analysis via state-space averaging confirms output voltage regulation solely through duty-cycle adjustment, independent of component variations. Experimental validation using 20 mm × 20 mm plates through 4-mm pigskin demonstrates 207 mW power transfer with 30.1% efficiency at 1 MHz with a simplified receiver circuit (1 diode/1 inductor/1 capacitor). The system maintains 3.7 V output under 150% load transients, 100% inductance variations, fat content change and issue bending.
- 10 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (2) , 1646-1651
A Single-Switch and Parameter-Insensitive Capacitive Power Transfer System for Biomedical Implants
This letter proposes a nonresonant capacitive power transfer system for active biomedical implants that eliminates resonance dependency while maintaining physical isolation. By leveraging biological tissue as the dielectric medium in a four-plate coupler and drawing inspiration from Zeta converter topology, the system achieves parameter insensitivity and single-switch control. Theoretical analysis via state-space averaging confirms output voltage regulation solely through duty-cycle adjustment, independent of component variations. Experimental validation using 20 mm × 20 mm plates through 4-mm pigskin demonstrates 207 mW power transfer with 30.1% efficiency at 1 MHz with a simplified receiver circuit (1 diode/1 inductor/1 capacitor). The system maintains 3.7 V output under 150% load transients, 100% inductance variations, fat content change and issue bending.
- 30 July 2025
- Published by Springer Nature in Electrical Engineering
- Vol. 107 (11) , 14483-14500
Modeling and performance assessment of IPT systems for powering sensors in metallic enclosures
- 30 July 2025
- Published by Springer Nature in Electrical Engineering
- Vol. 107 (11) , 14483-14500
Modeling and performance assessment of IPT systems for powering sensors in metallic enclosures
- 1 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (8) , 11076-11087
Phase-Shift Modulated Hybrid SCLLC Topology at Fixed-Frequency for Wide Voltage Range Without Extra Components
In the application of an intermediate bus converter, the traditional frequency-modulated LLC suffers from low regulation efficiency, bulky magnetic components, and high electromagnetic interference (EMI). In this work, a hybrid SCLLC topology is proposed by integrating a switched-capacitor (SC) converter with the LLC converter. Thanks to the additional power delivery path provided by SC, partial power can be delivered directly to the load without passing through the transformer, thereby improving efficiency. In the proposed integrated topology, the stacked bridge and resonant tank in the SC and LLC are multiplexed without adding any components. Besides, a fixed-frequency phase-shift modulation strategy is employed for voltage regulation, which is beneficial to reduce the size of the magnetic components and limit EMI. Moreover, zero-voltage switching is well-realized for all primary switches in a wide range. Finally, an experimental prototype with a 40–60 V input and 12 V/200 W output demonstrates a peak efficiency of 97.5%, validating the proposed topology. At 60 V input, owing to the higher SC power ratio, the system achieves an efficiency over 95% across the full load range (2 A–16 A).
- 1 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (8) , 11076-11087
Phase-Shift Modulated Hybrid SCLLC Topology at Fixed-Frequency for Wide Voltage Range Without Extra Components
In the application of an intermediate bus converter, the traditional frequency-modulated LLC suffers from low regulation efficiency, bulky magnetic components, and high electromagnetic interference (EMI). In this work, a hybrid SCLLC topology is proposed by integrating a switched-capacitor (SC) converter with the LLC converter. Thanks to the additional power delivery path provided by SC, partial power can be delivered directly to the load without passing through the transformer, thereby improving efficiency. In the proposed integrated topology, the stacked bridge and resonant tank in the SC and LLC are multiplexed without adding any components. Besides, a fixed-frequency phase-shift modulation strategy is employed for voltage regulation, which is beneficial to reduce the size of the magnetic components and limit EMI. Moreover, zero-voltage switching is well-realized for all primary switches in a wide range. Finally, an experimental prototype with a 40–60 V input and 12 V/200 W output demonstrates a peak efficiency of 97.5%, validating the proposed topology. At 60 V input, owing to the higher SC power ratio, the system achieves an efficiency over 95% across the full load range (2 A–16 A).
- 26 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4230-4238
A Secondary-Side Rotating and Segmented Capacitive Power Transfer System With Low Output Voltage Fluctuations Based on Three DC Busbars
In mechanical power transmission equipment, the power shafts are common mechanical structure. It is not feasible to use traditional power supply methods to supply power from fixed power sources to rotating equipment. Capacitive power transfer (CPT) technology has the advantages of flexible and portable couplers, low eddy current loss, and these advantages are well suited to the power supply needs of equipment installed on rotating bodies. However, there are also some shafts with large diameters that can cause serious electromagnetic radiation and standby losses when using long receiving plates, and a series of problems such as voltage drops caused by segmented couplers. Therefore, this paper proposes a rotating segmented CPT system with low output voltage fluctuation based on three DC busbars; it establishes a mathematical model and equivalent circuit for the system’s multi-port capacitive coupling; and achieves the super-position of adjacent rectified output voltages. Experimental results confirms that the system maintains a basically constant output voltage throughout the entire rotation process. In this process, the output voltage of the system drops from 47V to 41V, with a maximum variation rate of 12.77%. The system output power reaches 82W, and the peak efficiency achieves 84.97%.
- 26 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4230-4238
A Secondary-Side Rotating and Segmented Capacitive Power Transfer System With Low Output Voltage Fluctuations Based on Three DC Busbars
In mechanical power transmission equipment, the power shafts are common mechanical structure. It is not feasible to use traditional power supply methods to supply power from fixed power sources to rotating equipment. Capacitive power transfer (CPT) technology has the advantages of flexible and portable couplers, low eddy current loss, and these advantages are well suited to the power supply needs of equipment installed on rotating bodies. However, there are also some shafts with large diameters that can cause serious electromagnetic radiation and standby losses when using long receiving plates, and a series of problems such as voltage drops caused by segmented couplers. Therefore, this paper proposes a rotating segmented CPT system with low output voltage fluctuation based on three DC busbars; it establishes a mathematical model and equivalent circuit for the system’s multi-port capacitive coupling; and achieves the super-position of adjacent rectified output voltages. Experimental results confirms that the system maintains a basically constant output voltage throughout the entire rotation process. In this process, the output voltage of the system drops from 47V to 41V, with a maximum variation rate of 12.77%. The system output power reaches 82W, and the peak efficiency achieves 84.97%.