Manish Pal Chowdhury
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Manish Pal Chowdhury has a total of 87 co-authors. Here are the top co-authors by number of shared publications:
- Soumalya Kundu
IIEST Shibpur
13 shared publications - Rahul Majumder
IIEST Shibpur
11 shared publications - Ria Ghosh
IIEST Shibpur
5 shared publications Mainak Swarnakar
Department of Physics IIEST Shibpur Howrah West Bengal India
4 shared publicationsRahul Majumder
4 shared publications- Subhadip Roy
IISER Kolkata
4 shared publications
Latest Publications
- Open Access
- 16 August 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (18) , e71177
Multifunctional PVDF/SrTiO 3 /PEDOT:PSS Ternary Nanocomposite for Energy‐Harvesting and Piezo‐Photocatalytic Applications
In this study, a lead‐free ternary poly(vinylidene fluoride) (PVDF)/strontium titanate (SrTiO 3 )/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) nanocomposite was developed to enhance piezoelectric and piezo‐photocatalytic performance. SrTiO 3 nanoparticles (NPs) were synthesized via an autocombustion route and incorporated with PEDOT:PSS into the PVDF matrix, utilizing the solution‐casting method. Structural and spectroscopic analyses confirmed the successful formation of cubic‐phase SrTiO 3 NPs and their uniform incorporation within the polymer matrix. The incorporation of SrTiO 3 NPs and PEDOT:PSS significantly promoted electroactive phase formation in PVDF, yielding an electroactive phase content of 97.74% for the optimized composite. Complex impedance spectroscopy revealed enhanced interfacial polarization and improved dielectric behavior. Consequently, the optimized nanocomposite exhibited a high dielectric constant ε ′ ≈ 101.26 at 40 Hz frequency. The corresponding piezoelectric nanogenerator delivered an open‐circuit voltage of 45.50 ± 0.58 V and a maximum power density of 51.76 ± 1.33 μW cm −2 under periodic mechanical excitation. Furthermore, the optimized composite demonstrated enhanced piezo‐photocatalytic degradation of methylene blue dye, attributed to efficient charge separation induced by the piezoelectric potential under simultaneous mechanical and light stimulation.
- 16 August 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (18) , e71177
Open AccessMultifunctional PVDF/SrTiO 3 /PEDOT:PSS Ternary Nanocomposite for Energy‐Harvesting and Piezo‐Photocatalytic Applications
In this study, a lead‐free ternary poly(vinylidene fluoride) (PVDF)/strontium titanate (SrTiO 3 )/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) nanocomposite was developed to enhance piezoelectric and piezo‐photocatalytic performance. SrTiO 3 nanoparticles (NPs) were synthesized via an autocombustion route and incorporated with PEDOT:PSS into the PVDF matrix, utilizing the solution‐casting method. Structural and spectroscopic analyses confirmed the successful formation of cubic‐phase SrTiO 3 NPs and their uniform incorporation within the polymer matrix. The incorporation of SrTiO 3 NPs and PEDOT:PSS significantly promoted electroactive phase formation in PVDF, yielding an electroactive phase content of 97.74% for the optimized composite. Complex impedance spectroscopy revealed enhanced interfacial polarization and improved dielectric behavior. Consequently, the optimized nanocomposite exhibited a high dielectric constant ε ′ ≈ 101.26 at 40 Hz frequency. The corresponding piezoelectric nanogenerator delivered an open‐circuit voltage of 45.50 ± 0.58 V and a maximum power density of 51.76 ± 1.33 μW cm −2 under periodic mechanical excitation. Furthermore, the optimized composite demonstrated enhanced piezo‐photocatalytic degradation of methylene blue dye, attributed to efficient charge separation induced by the piezoelectric potential under simultaneous mechanical and light stimulation.
- 8 August 2026
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 219
Defect-mediated carrier trapping and interfacial relaxation dynamics in ZnO-based UV photodetector
- 8 August 2026
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 219
Defect-mediated carrier trapping and interfacial relaxation dynamics in ZnO-based UV photodetector
- 22 February 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 87
UV-mediated defect engineering in ZnO nanostructures for enhanced photodetection with IoT-enabled real-time monitoring
- 22 February 2026
- Published by Elsevier in Surfaces and Interfaces
- Vol. 87
UV-mediated defect engineering in ZnO nanostructures for enhanced photodetection with IoT-enabled real-time monitoring
- 1 November 2024
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 115 (11-12) , 881-889
A complex impedance spectroscopy study on PVDF/PANI/CoFe2O4 composites
The synthesis of polymer composites consisting of conducting polyaniline (PANI), cobalt ferrite (CoFe2O4), and poly(vinylidene fluoride) (PVDF) is achieved by the polymerization technique. A nanocomposite consisting of polyaniline (PANI) and CoFe2O4 is prepared using the interfacial chemical oxidation polymerization technique, resulting in a composition containing 50 wt.% of CoFe2O4. Nanoparticles of cobalt ferrite (CoFe2O4) were synthesized by using the sol–gel auto-combustion process. The PANI/CoFe2O4 (1:1) nanocomposites with weight percentages of 5, 10, 15, and 20 are incorporated into the PVDF matrix as fillers in order to alter the morphology and AC electrical conductivity of the PVDF/PANI/CoFe2O4 composite materials. The structural and morphological properties were studied using characterization techniques such as X-ray diffraction, Fourier transform infrared spectroscopy, and field emission scanning electron microscopy. At room temperature, impedance spectroscopy, dielectric measurements, and AC electrical conductivity were carried out in the frequency range of 40 Hz to 5 MHz. The dielectric permittivity has been shown to decline exponentially in low-frequency zones before remaining almost constant up to 5 MHz. When the frequency is increased up to 1 MHz, the AC conductivity of all composites remains constant; after that, it increases as the frequency increases. It was found that PANI-CoFe2O4 nanocomposites modified the overall charge transport mechanism by modulating the core grain and grain boundary. The experimental Nyquist plot for different composite samples was fitted by an appropriate RC electrical model to evaluate relaxation time. The relaxation time τ 1 (R 1 C 1) and τ 2 (R 2 C 2) were both reduced after the reinforcement of PANI-CoFe2O4 nanocomposites.
- 1 November 2024
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 115 (11-12) , 881-889
A complex impedance spectroscopy study on PVDF/PANI/CoFe2O4 composites
The synthesis of polymer composites consisting of conducting polyaniline (PANI), cobalt ferrite (CoFe2O4), and poly(vinylidene fluoride) (PVDF) is achieved by the polymerization technique. A nanocomposite consisting of polyaniline (PANI) and CoFe2O4 is prepared using the interfacial chemical oxidation polymerization technique, resulting in a composition containing 50 wt.% of CoFe2O4. Nanoparticles of cobalt ferrite (CoFe2O4) were synthesized by using the sol–gel auto-combustion process. The PANI/CoFe2O4 (1:1) nanocomposites with weight percentages of 5, 10, 15, and 20 are incorporated into the PVDF matrix as fillers in order to alter the morphology and AC electrical conductivity of the PVDF/PANI/CoFe2O4 composite materials. The structural and morphological properties were studied using characterization techniques such as X-ray diffraction, Fourier transform infrared spectroscopy, and field emission scanning electron microscopy. At room temperature, impedance spectroscopy, dielectric measurements, and AC electrical conductivity were carried out in the frequency range of 40 Hz to 5 MHz. The dielectric permittivity has been shown to decline exponentially in low-frequency zones before remaining almost constant up to 5 MHz. When the frequency is increased up to 1 MHz, the AC conductivity of all composites remains constant; after that, it increases as the frequency increases. It was found that PANI-CoFe2O4 nanocomposites modified the overall charge transport mechanism by modulating the core grain and grain boundary. The experimental Nyquist plot for different composite samples was fitted by an appropriate RC electrical model to evaluate relaxation time. The relaxation time τ 1 (R 1 C 1) and τ 2 (R 2 C 2) were both reduced after the reinforcement of PANI-CoFe2O4 nanocomposites.
- 16 November 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (44) , 17019-17033
Synthesis and characterisation of carbon nanotubes and zinc oxide composites: sub-millisecond UV response
- 16 November 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (44) , 17019-17033
Synthesis and characterisation of carbon nanotubes and zinc oxide composites: sub-millisecond UV response
- 18 October 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (1)
Superior ammonia sensing properties of PET‐supported polyaniline/reduced graphene oxide/zinc ferrite ternary nanocomposite thin film at room temperature
This article introduces a ternary nanocomposite‐based flexible thin film ammonia sensor developed on transparent polyethylene terephthalate (PET) substrate in the well‐known in situ chemical oxidative polymerization technique. The nanocomposite consists of three different materials: polyaniline (PANI), reduced graphene oxide (rGO), and zinc ferrite (ZF). Keeping the PANI amount constant, seven PANI/rGO/ZF (PRZ) samples are produced by performing stoichiometric variation between rGO and ZF. Later on, various structural, morphological, and spectroscopic analysis of all the composite materials is accomplished with field emission scanning electron microscopy (FESEM), high‐resolution transmission electron microscopy (HRTEM), X‐ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), and ultraviolet–visible spectroscopy (UV–Vis). The sensing performance of the as‐produced sensors toward ammonia (NH3) is examined in the concentration range from 250 ppb to 100 ppm. The study reveals the excellent sensing ability of the PRZ3 sensor (rGO = 30%, ZF = 20%) achieving minimum and maximum responsivity values of ~51% and ~1052%, respectively, at the lowest (250 ppb) and highest (100 ppm) concentration of ammonia. The sensor also exhibits admirable repeatability, good dynamic responsivity, rapid response (tres ~2.9–5 s), moderately faster recovery (trec ~37.9–69.7 s), superb linearity against ppm variation (R2 ~ 0.989), low detection limit (~123 ppb), and exceptional selectivity toward ammonia. The substrate temperature variation divulges that room temperature (30°C) is the ideal temperature for getting outstanding responsivity of the sensor. The study is further accompanied by humidity variation in the incoming air and bending flexibility test of the substrate. A compulsory and legitimate model regarding the sensing mechanism is presented at the end.
- 18 October 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (1)
Superior ammonia sensing properties of PET‐supported polyaniline/reduced graphene oxide/zinc ferrite ternary nanocomposite thin film at room temperature
This article introduces a ternary nanocomposite‐based flexible thin film ammonia sensor developed on transparent polyethylene terephthalate (PET) substrate in the well‐known in situ chemical oxidative polymerization technique. The nanocomposite consists of three different materials: polyaniline (PANI), reduced graphene oxide (rGO), and zinc ferrite (ZF). Keeping the PANI amount constant, seven PANI/rGO/ZF (PRZ) samples are produced by performing stoichiometric variation between rGO and ZF. Later on, various structural, morphological, and spectroscopic analysis of all the composite materials is accomplished with field emission scanning electron microscopy (FESEM), high‐resolution transmission electron microscopy (HRTEM), X‐ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), and ultraviolet–visible spectroscopy (UV–Vis). The sensing performance of the as‐produced sensors toward ammonia (NH3) is examined in the concentration range from 250 ppb to 100 ppm. The study reveals the excellent sensing ability of the PRZ3 sensor (rGO = 30%, ZF = 20%) achieving minimum and maximum responsivity values of ~51% and ~1052%, respectively, at the lowest (250 ppb) and highest (100 ppm) concentration of ammonia. The sensor also exhibits admirable repeatability, good dynamic responsivity, rapid response (tres ~2.9–5 s), moderately faster recovery (trec ~37.9–69.7 s), superb linearity against ppm variation (R2 ~ 0.989), low detection limit (~123 ppb), and exceptional selectivity toward ammonia. The substrate temperature variation divulges that room temperature (30°C) is the ideal temperature for getting outstanding responsivity of the sensor. The study is further accompanied by humidity variation in the incoming air and bending flexibility test of the substrate. A compulsory and legitimate model regarding the sensing mechanism is presented at the end.
- 7 February 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (7) , 3147-3170
An in situ synthesis of polyaniline/reduced graphene oxide nanocomposite flexible thin film on PET for the room temperature detection of trace level ammonia at ppb level
- 7 February 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (7) , 3147-3170
An in situ synthesis of polyaniline/reduced graphene oxide nanocomposite flexible thin film on PET for the room temperature detection of trace level ammonia at ppb level
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
An In-Situ Synthesis of Polyaniline/Reduced Graphene Oxide Nanocomposite Flexible Thin Film on Pet for the Room Temperature Detection of Trace Level Ammonia at Ppb Level
Ammonia being a major environmental pollutant, the regulation and its specific detection is tremendously important. To meet the urgency, the present article brings out a cost-effective, easy handling and enduring material of reduced graphene oxide (rGO) doped polyaniline (PANI). Attempting an in-situ chemical oxidation technique, thin films of this material were prepared on polyethylene terephthalate (PET) substrates at different doping percentages of rGO, varying between 0-10%. Furthermore, during the synthesis, various amount of hydrochloric acid (HCl) was dissolved within the precursor solution to achieve different acid molar concentration ranging between 0.1 (M) and 2 (M). Structural and compositional analysis of the materials were performed thereafter with X-ray diffraction (XRD). Three different spectroscopic studies, named as, Fourier transform infrared (FTIR), Raman and ultraviolet-visible (UV-VIS) spectroscopy, were further carried out to analyse the chemical bond, vibrational modes and band gap respectively. In addition, the surface morphology of the thin films was examined with field emission scanning electron microscopy (FESEM). To know the accurate size of the PANI and rGO, high-resolution transmission electron microscopy (HRTEM) was conducted. The study of ammonia (NH 3 ) sensing in the domain of 50 ppb to 80 ppm exhibits lucrative sensitivity (~ 486% @ 80 ppm and 33% @ 50 ppb) at room temperature (25°C), outstanding repeatability in the response curves, well-fitted response curve with the power-law (P ~ 0.71), much faster response/recovery times (t res /t rec =2.1s/57.1s @ 80 ppm and 3.7s/112.9s @ 50 ppb) and incomparably high selectivity towards NH 3 . The rGO doping variation together with HCl molarity variation yield that all of the aforementioned supremacy data have been exhibited by 1% PANI-rGO sample synthesized in 1(M) HCl concentration. The frequency dependence of the sample impedance was studied using impedance spectroscopy in the wide frequency range. Density functional theory calculations were also performed to understand the charge transfer mechanism, adsorption strength and recovery time for NH 3 adsorbed rGO, PANI and rGO-PANI heterostructure. The significant charge transfer and formation of interfacial electric field explained the importance of rGO-PANI interface in NH 3 sensing.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessAn In-Situ Synthesis of Polyaniline/Reduced Graphene Oxide Nanocomposite Flexible Thin Film on Pet for the Room Temperature Detection of Trace Level Ammonia at Ppb Level
Ammonia being a major environmental pollutant, the regulation and its specific detection is tremendously important. To meet the urgency, the present article brings out a cost-effective, easy handling and enduring material of reduced graphene oxide (rGO) doped polyaniline (PANI). Attempting an in-situ chemical oxidation technique, thin films of this material were prepared on polyethylene terephthalate (PET) substrates at different doping percentages of rGO, varying between 0-10%. Furthermore, during the synthesis, various amount of hydrochloric acid (HCl) was dissolved within the precursor solution to achieve different acid molar concentration ranging between 0.1 (M) and 2 (M). Structural and compositional analysis of the materials were performed thereafter with X-ray diffraction (XRD). Three different spectroscopic studies, named as, Fourier transform infrared (FTIR), Raman and ultraviolet-visible (UV-VIS) spectroscopy, were further carried out to analyse the chemical bond, vibrational modes and band gap respectively. In addition, the surface morphology of the thin films was examined with field emission scanning electron microscopy (FESEM). To know the accurate size of the PANI and rGO, high-resolution transmission electron microscopy (HRTEM) was conducted. The study of ammonia (NH 3 ) sensing in the domain of 50 ppb to 80 ppm exhibits lucrative sensitivity (~ 486% @ 80 ppm and 33% @ 50 ppb) at room temperature (25°C), outstanding repeatability in the response curves, well-fitted response curve with the power-law (P ~ 0.71), much faster response/recovery times (t res /t rec =2.1s/57.1s @ 80 ppm and 3.7s/112.9s @ 50 ppb) and incomparably high selectivity towards NH 3 . The rGO doping variation together with HCl molarity variation yield that all of the aforementioned supremacy data have been exhibited by 1% PANI-rGO sample synthesized in 1(M) HCl concentration. The frequency dependence of the sample impedance was studied using impedance spectroscopy in the wide frequency range. Density functional theory calculations were also performed to understand the charge transfer mechanism, adsorption strength and recovery time for NH 3 adsorbed rGO, PANI and rGO-PANI heterostructure. The significant charge transfer and formation of interfacial electric field explained the importance of rGO-PANI interface in NH 3 sensing.