Zehui Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zehui Wang has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Qirong Xiao
Tsinghua University
16 shared publications - Jiading Tian
Tsinghua University
14 shared publications Mali Gong
Tsinghua University
13 shared publications- Ping Yan
Tsinghua University
13 shared publications Dan Li
Tsinghua University
10 shared publications- Dan Li
Tsinghua University
9 shared publications
Latest Publications
- 17 October 2022
- Published by Optica Publishing Group in Photonics Research
- Vol. 10 (11) , 2513-2525
On the initiation of fiber fuse damage in high-power ytterbium-doped fiber lasers
Fiber fuse effect can occur spontaneously and propagate along optical fibers to cause widespread damage; it threatens all applications involving optical fibers. This paper presents two results. First, it establishes that the initiation of fiber fuse (IFF) in silica fibers is caused by virtual-defect-induced absorption. Critical temperatures and critical optical powers for IFF are simulated for the first time using a 3D solid-state heat transfer model with heat source generated by the virtual-defect-induced absorption. In this method, formation energies of the virtual defects can be uniquely determined, which offers critical information on the chemical reasons for fiber fuse. Second, this paper offers a method to evaluate operating temperatures of fiber lasers. General analytical solutions of the operating temperatures along gain fibers are deduced. Results of 976-nm laser-diode-pumped and 1018-nm tandem-pumped ytterbium-doped fiber (YDF) amplifiers using 10/130-μm YDFs are calculated. Potential limits caused by fiber fuse are discussed.
- 17 October 2022
- Published by Optica Publishing Group in Photonics Research
- Vol. 10 (11) , 2513-2525
On the initiation of fiber fuse damage in high-power ytterbium-doped fiber lasers
Fiber fuse effect can occur spontaneously and propagate along optical fibers to cause widespread damage; it threatens all applications involving optical fibers. This paper presents two results. First, it establishes that the initiation of fiber fuse (IFF) in silica fibers is caused by virtual-defect-induced absorption. Critical temperatures and critical optical powers for IFF are simulated for the first time using a 3D solid-state heat transfer model with heat source generated by the virtual-defect-induced absorption. In this method, formation energies of the virtual defects can be uniquely determined, which offers critical information on the chemical reasons for fiber fuse. Second, this paper offers a method to evaluate operating temperatures of fiber lasers. General analytical solutions of the operating temperatures along gain fibers are deduced. Results of 976-nm laser-diode-pumped and 1018-nm tandem-pumped ytterbium-doped fiber (YDF) amplifiers using 10/130-μm YDFs are calculated. Potential limits caused by fiber fuse are discussed.
- 15 June 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12285, 34-163
Improved wind power output forecasting method based on combination of grey model and BP neural network
The traditional grey prediction model has the problem of low prediction accuracy in wind power generation prediction. In this paper, an improved Grey prediction model is proposed by smoothing the original data, and a combination prediction model is constructed by combining it with BP neural network. The example shows that the accuracy of the improved optimal combination forecasting model is higher than that of the single forecasting model, and is better than that of the traditional optimal combination forecasting model.
- 15 June 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12285, 34-163
Improved wind power output forecasting method based on combination of grey model and BP neural network
The traditional grey prediction model has the problem of low prediction accuracy in wind power generation prediction. In this paper, an improved Grey prediction model is proposed by smoothing the original data, and a combination prediction model is constructed by combining it with BP neural network. The example shows that the accuracy of the improved optimal combination forecasting model is higher than that of the single forecasting model, and is better than that of the traditional optimal combination forecasting model.
- 14 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (12) , 3907-3915
6.85 kW Ytterbium-Raman Fiber Amplifier Based on Adjustable Raman Threshold Method
To achieve a high spectral purity Raman laser in a wide range of pump power, we propose the adjustable Raman threshold method and experimentally demonstrate a 6.85 kW ytterbium-Raman (Yb-Raman) fiber amplifier in this paper. The Raman threshold is adjusted to coordinate with pump power level via manipulating the Raman proportion from the master oscillator. The spectral purity of Raman laser at 1120 nm reaches 86.0 % at the highest output power and keeps over 65 % throughout. And the 3 dB bandwidth is maintained within 2.5 nm. The system shows potential in further power scaling-up because the four-wave-mixing-induced high-order Raman noise is circumvented by designing wavelengths of the seeders. This work not only reports the highest output power of the Yb-Raman fiber lasers (to the best of our knowledge), but also provides an approach to achieve an agile lasing threshold in the Yb-Raman fiber amplifiers without any structural adjustments. The Yb-Raman fiber amplifiers with high spectral purity over a broad range of power will have promising applications in communications, industry and scientific researches.
- 14 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (12) , 3907-3915
6.85 kW Ytterbium-Raman Fiber Amplifier Based on Adjustable Raman Threshold Method
To achieve a high spectral purity Raman laser in a wide range of pump power, we propose the adjustable Raman threshold method and experimentally demonstrate a 6.85 kW ytterbium-Raman (Yb-Raman) fiber amplifier in this paper. The Raman threshold is adjusted to coordinate with pump power level via manipulating the Raman proportion from the master oscillator. The spectral purity of Raman laser at 1120 nm reaches 86.0 % at the highest output power and keeps over 65 % throughout. And the 3 dB bandwidth is maintained within 2.5 nm. The system shows potential in further power scaling-up because the four-wave-mixing-induced high-order Raman noise is circumvented by designing wavelengths of the seeders. This work not only reports the highest output power of the Yb-Raman fiber lasers (to the best of our knowledge), but also provides an approach to achieve an agile lasing threshold in the Yb-Raman fiber amplifiers without any structural adjustments. The Yb-Raman fiber amplifiers with high spectral purity over a broad range of power will have promising applications in communications, industry and scientific researches.
- 21 December 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (1) , 296-307
Spectral pedestal during the kilowatt-level amplification of a random fiber laser operating near the lasing threshold
The amplification of random fiber lasers (RFLs) attracts much attention due to their unique characteristics such as wavelength flexibility and low coherence. We present that, in the kilowatt-level amplification of RFL operating near its lasing threshold, a broad and flat spectral pedestal can co-exist with the narrow spectral peak of RFL. This phenomenon is different from the case in the amplification of fixed-cavity laser seeds. Time-domain measurements show that the broad and flat spectral pedestal, which extends to long wavelengths, is composed of temporal pulses, while few temporal pulses exist in the narrow spectral peak. We attribute the spectral pedestal to intensity fluctuations from the random seed laser and modulation instability in the amplification stage. Control experiments reveal that the working status of the random seed laser and the effective length of the amplifier can influence the spectral bandwidth. By taking advantage of this phenomenon, we propose a novel approach to achieve a high-power broadband light source through the amplification of RFLs operating near the lasing threshold.
- 21 December 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (1) , 296-307
Spectral pedestal during the kilowatt-level amplification of a random fiber laser operating near the lasing threshold
The amplification of random fiber lasers (RFLs) attracts much attention due to their unique characteristics such as wavelength flexibility and low coherence. We present that, in the kilowatt-level amplification of RFL operating near its lasing threshold, a broad and flat spectral pedestal can co-exist with the narrow spectral peak of RFL. This phenomenon is different from the case in the amplification of fixed-cavity laser seeds. Time-domain measurements show that the broad and flat spectral pedestal, which extends to long wavelengths, is composed of temporal pulses, while few temporal pulses exist in the narrow spectral peak. We attribute the spectral pedestal to intensity fluctuations from the random seed laser and modulation instability in the amplification stage. Control experiments reveal that the working status of the random seed laser and the effective length of the amplifier can influence the spectral bandwidth. By taking advantage of this phenomenon, we propose a novel approach to achieve a high-power broadband light source through the amplification of RFLs operating near the lasing threshold.
- 1 January 2021
- Published by Elsevier in Optics & Laser Technology
- Vol. 133
3 kW narrow linewidth high spectral density continuous wave fiber laser based on fiber Bragg grating
- 1 January 2021
- Published by Elsevier in Optics & Laser Technology
- Vol. 133
3 kW narrow linewidth high spectral density continuous wave fiber laser based on fiber Bragg grating
- 30 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 57 (2) , 1-9
5.1 kW Tandem-Pumped Fiber Amplifier Seeded by Random Fiber Laser With High Suppression of Stimulated Raman Scattering
In this work, high-power tandem-pumped random fiber lasers are investigated in detail. A 6.5 W random fiber laser seed centered at 1070 nm with a half-open cavity structure was built. Boosted by two amplifier stages, the random fiber laser achieved a power of several kilowatts. Stimulated Raman scattering (SRS) mitigation is challenging in tandem-pumped fiber lasers. To suppress SRS, several methods were applied, including avoiding external feedback in the oscillator stage, incorporating a high core/cladding diameter ratio gain fiber, and using a band pass filter (BPF) to mitigate Raman noise. The latter proved to be the most effective method; therefore, SRS mitigation without and with a BPF was investigated at 3.5 kW, leading to suppression ratios rising from 14 to 30 dB. By increasing the pump power continuously to 5.6 kW, we realized a record output power of 5.1 kW, corresponding to an SRS suppression ratio of 27 dB. Owing to the high-brightness 1018 nm fiber lasers serving as the pump sources and the high gain coefficient in the second amplifier stage, the entire system demonstrated high efficiency and stability. At the maximum power level, the total optical-to-optical efficiency reached 89.0%. This work offers an economic and practical technique for realizing high-power and high-efficiency random fiber lasers with effective SRS mitigation, while the experimental results suggest the potential for further power scaling.
- 30 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 57 (2) , 1-9
5.1 kW Tandem-Pumped Fiber Amplifier Seeded by Random Fiber Laser With High Suppression of Stimulated Raman Scattering
In this work, high-power tandem-pumped random fiber lasers are investigated in detail. A 6.5 W random fiber laser seed centered at 1070 nm with a half-open cavity structure was built. Boosted by two amplifier stages, the random fiber laser achieved a power of several kilowatts. Stimulated Raman scattering (SRS) mitigation is challenging in tandem-pumped fiber lasers. To suppress SRS, several methods were applied, including avoiding external feedback in the oscillator stage, incorporating a high core/cladding diameter ratio gain fiber, and using a band pass filter (BPF) to mitigate Raman noise. The latter proved to be the most effective method; therefore, SRS mitigation without and with a BPF was investigated at 3.5 kW, leading to suppression ratios rising from 14 to 30 dB. By increasing the pump power continuously to 5.6 kW, we realized a record output power of 5.1 kW, corresponding to an SRS suppression ratio of 27 dB. Owing to the high-brightness 1018 nm fiber lasers serving as the pump sources and the high gain coefficient in the second amplifier stage, the entire system demonstrated high efficiency and stability. At the maximum power level, the total optical-to-optical efficiency reached 89.0%. This work offers an economic and practical technique for realizing high-power and high-efficiency random fiber lasers with effective SRS mitigation, while the experimental results suggest the potential for further power scaling.
- 3 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (10) , 573-576
An Efficient Non-Invasive Method to Fabricate In-Fiber Microcavities Using a Continuous-Wave Laser
In-fiber microcavities are usually fabricated by inva-sive methods that require costly setups and time-consuming processes. Inspired by the fiber fuse effect, we propose an efficient non-invasive method to fabricate in-fiber microcavities. The setup of the method was economic, using a watt-level continuous-wave laser. Spherical in-fiber microcavities of ~hundred-of-micron sizes could be fabricated and freely integrated in fibers. The fabrication rate was seconds-per-microcavity, being hundreds of times faster than previous methods. The microcavities could have ~1-micron-thin cavity walls and ~104 high quality factors as Fabry-Perot reso-nators. The method offers many unique features for microcavities and can be useful for large-scale fabrication. It can benefit many applications such as sensing and nonlinear frequency generation
- 3 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (10) , 573-576
An Efficient Non-Invasive Method to Fabricate In-Fiber Microcavities Using a Continuous-Wave Laser
In-fiber microcavities are usually fabricated by inva-sive methods that require costly setups and time-consuming processes. Inspired by the fiber fuse effect, we propose an efficient non-invasive method to fabricate in-fiber microcavities. The setup of the method was economic, using a watt-level continuous-wave laser. Spherical in-fiber microcavities of ~hundred-of-micron sizes could be fabricated and freely integrated in fibers. The fabrication rate was seconds-per-microcavity, being hundreds of times faster than previous methods. The microcavities could have ~1-micron-thin cavity walls and ~104 high quality factors as Fabry-Perot reso-nators. The method offers many unique features for microcavities and can be useful for large-scale fabrication. It can benefit many applications such as sensing and nonlinear frequency generation
- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (9) , 518-521
1535–1620 nm Widely Tunable Watt-Level Single-Mode Er:Yb Codoped All-Fiber MOPA
We report a continuous-wave 1535-1620 nm widely tunable single-mode Er:Yb codoped cladding-pumped all-fiber laser source based on the MOPA scheme. The output power ranged from 0.785 W (at 1615 nm) to 2.007 W (at 1565 nm), which is the highest output power from a C+L tunable all-fiber laser source. The 3 dB spectral width was less than 150 pm at all wavelengths. No Yb emission was observed. We proposed a mid-way backward pumping configuration in which the pump light was injected between two gain fibers and propagated backward to broaden the effective wavelength range of the fiber amplifier. Experiments verified the capability of our configuration to improve the suppression ratio of C-band amplified spontaneous emissions from 13 dB to 35 dB when the signal laser was operating at 1620 nm.
- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (9) , 518-521
1535–1620 nm Widely Tunable Watt-Level Single-Mode Er:Yb Codoped All-Fiber MOPA
We report a continuous-wave 1535-1620 nm widely tunable single-mode Er:Yb codoped cladding-pumped all-fiber laser source based on the MOPA scheme. The output power ranged from 0.785 W (at 1615 nm) to 2.007 W (at 1565 nm), which is the highest output power from a C+L tunable all-fiber laser source. The 3 dB spectral width was less than 150 pm at all wavelengths. No Yb emission was observed. We proposed a mid-way backward pumping configuration in which the pump light was injected between two gain fibers and propagated backward to broaden the effective wavelength range of the fiber amplifier. Experiments verified the capability of our configuration to improve the suppression ratio of C-band amplified spontaneous emissions from 13 dB to 35 dB when the signal laser was operating at 1620 nm.
- 20 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (6) , 1461-1467
Tandem-Pumped High-Power Narrow-Linewidth Fiber Laser Tunable From 1060–1090 nm
Tandem pumping is a promising technique for gain-ing higher power from ytterbium-doped fiber (YDF) lasers. How-ever, the characteristics of tandem pumped laser light, especially their variation with the lasing wavelengths, were not thoroughly investigated. We investigated the characteristics with the first 1018-nm tandem-pumped high-power tunable YDF laser. The 1018-nm tandem pumping was not applicable in tunable fiber lasers before because its much-lower absorption requires com-pensation of long YDFs, which enhances destructive nonlinear effects as a barrel effect for tuning wavelengths. Here, the setup used a fiber ring-cavity as seed, which was much more cost-effec-tive than conventional setups, and only 3 stages of amplification, of which the last stage was unidirectional tandem-pumped. By deliberate system design, it gained over 1-kW output powers at wavelengths tuning from 1060 nm to 1090 nm with ~100-pm 3dB-linewidths and 79.4%~85.6% slope efficiencies. Amplified spon-taneous emissions (ASE) and stimulated Brillouin scattering (SBS) caused no limits for further scaling powers. Variations of spectra and beam qualities of the outputs with the tuning wavelengths were detailly revealed in experiment. Drastically varying line-widths at ~1062 and ~1080 nm suggested complex evolution of the nonlinear effects with the pump light. This study offers not only an economic seed setup to high-power narrow-linewidth tunable fiber lasers, but detailed characteristics of laser amplified with 1018-nm pump in YDFs. The knowledge of the characteristics can usefully guide future design of high-performance tandem-pumped fiber lasers.
- 20 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (6) , 1461-1467
Tandem-Pumped High-Power Narrow-Linewidth Fiber Laser Tunable From 1060–1090 nm
Tandem pumping is a promising technique for gain-ing higher power from ytterbium-doped fiber (YDF) lasers. How-ever, the characteristics of tandem pumped laser light, especially their variation with the lasing wavelengths, were not thoroughly investigated. We investigated the characteristics with the first 1018-nm tandem-pumped high-power tunable YDF laser. The 1018-nm tandem pumping was not applicable in tunable fiber lasers before because its much-lower absorption requires com-pensation of long YDFs, which enhances destructive nonlinear effects as a barrel effect for tuning wavelengths. Here, the setup used a fiber ring-cavity as seed, which was much more cost-effec-tive than conventional setups, and only 3 stages of amplification, of which the last stage was unidirectional tandem-pumped. By deliberate system design, it gained over 1-kW output powers at wavelengths tuning from 1060 nm to 1090 nm with ~100-pm 3dB-linewidths and 79.4%~85.6% slope efficiencies. Amplified spon-taneous emissions (ASE) and stimulated Brillouin scattering (SBS) caused no limits for further scaling powers. Variations of spectra and beam qualities of the outputs with the tuning wavelengths were detailly revealed in experiment. Drastically varying line-widths at ~1062 and ~1080 nm suggested complex evolution of the nonlinear effects with the pump light. This study offers not only an economic seed setup to high-power narrow-linewidth tunable fiber lasers, but detailed characteristics of laser amplified with 1018-nm pump in YDFs. The knowledge of the characteristics can usefully guide future design of high-performance tandem-pumped fiber lasers.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
An Efficient 4-kW Level Random Fiber Laser Based on Tandem-Pumping Scheme
In this paper, we presented a monolithic high power random fiber laser with a tandem-pumping scheme. The random fiber laser seed centered at 1064 nm was pumped by a 1018 nm fiber laser and reached an output power of 8.66 W. After the two amplifiers, the seed was amplified to 4020 W and the 3 dB width of laser spectrum was broadened from 0.78 nm to 0.99 nm. To increase the efficiency of the 4 kW laser, a specially designed high absorption coefficient (0.6 dB/m @ 1018nm) 30/250 μm Yb doped fiber and high brightness 1018 nm pump laser were adopted. The optical-to-optical efficiency could reach as high as 88.5%. No obvious mode instability was found during the experiment. Furthermore, with the same amplifier stage, we have also built another 4 kW level fiber laser seeded by an oscillator consisting of a pair of fiber Bragg gratings. The comparison of the experimental results showed that high power laser based on RFL seed would have a better control on spectral broadening.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
An Efficient 4-kW Level Random Fiber Laser Based on Tandem-Pumping Scheme
In this paper, we presented a monolithic high power random fiber laser with a tandem-pumping scheme. The random fiber laser seed centered at 1064 nm was pumped by a 1018 nm fiber laser and reached an output power of 8.66 W. After the two amplifiers, the seed was amplified to 4020 W and the 3 dB width of laser spectrum was broadened from 0.78 nm to 0.99 nm. To increase the efficiency of the 4 kW laser, a specially designed high absorption coefficient (0.6 dB/m @ 1018nm) 30/250 μm Yb doped fiber and high brightness 1018 nm pump laser were adopted. The optical-to-optical efficiency could reach as high as 88.5%. No obvious mode instability was found during the experiment. Furthermore, with the same amplifier stage, we have also built another 4 kW level fiber laser seeded by an oscillator consisting of a pair of fiber Bragg gratings. The comparison of the experimental results showed that high power laser based on RFL seed would have a better control on spectral broadening.