Jiading Tian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jiading Tian has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Qirong Xiao
Tsinghua University
18 shared publications Mali Gong
Tsinghua University
15 shared publications- Zehui Wang
Tsinghua University
14 shared publications - Ping Yan
Tsinghua University
13 shared publications Dan Li
Tsinghua University
11 shared publications- Dan Li
Tsinghua University
8 shared publications
Latest Publications
- 17 October 2022
- Published by Optica Publishing Group in Photonics Research
- Vol. 10 (11) , 2513-2525
On the initiation of fiber fuse damage in high-power ytterbium-doped fiber lasers
Fiber fuse effect can occur spontaneously and propagate along optical fibers to cause widespread damage; it threatens all applications involving optical fibers. This paper presents two results. First, it establishes that the initiation of fiber fuse (IFF) in silica fibers is caused by virtual-defect-induced absorption. Critical temperatures and critical optical powers for IFF are simulated for the first time using a 3D solid-state heat transfer model with heat source generated by the virtual-defect-induced absorption. In this method, formation energies of the virtual defects can be uniquely determined, which offers critical information on the chemical reasons for fiber fuse. Second, this paper offers a method to evaluate operating temperatures of fiber lasers. General analytical solutions of the operating temperatures along gain fibers are deduced. Results of 976-nm laser-diode-pumped and 1018-nm tandem-pumped ytterbium-doped fiber (YDF) amplifiers using 10/130-μm YDFs are calculated. Potential limits caused by fiber fuse are discussed.
- 17 October 2022
- Published by Optica Publishing Group in Photonics Research
- Vol. 10 (11) , 2513-2525
On the initiation of fiber fuse damage in high-power ytterbium-doped fiber lasers
Fiber fuse effect can occur spontaneously and propagate along optical fibers to cause widespread damage; it threatens all applications involving optical fibers. This paper presents two results. First, it establishes that the initiation of fiber fuse (IFF) in silica fibers is caused by virtual-defect-induced absorption. Critical temperatures and critical optical powers for IFF are simulated for the first time using a 3D solid-state heat transfer model with heat source generated by the virtual-defect-induced absorption. In this method, formation energies of the virtual defects can be uniquely determined, which offers critical information on the chemical reasons for fiber fuse. Second, this paper offers a method to evaluate operating temperatures of fiber lasers. General analytical solutions of the operating temperatures along gain fibers are deduced. Results of 976-nm laser-diode-pumped and 1018-nm tandem-pumped ytterbium-doped fiber (YDF) amplifiers using 10/130-μm YDFs are calculated. Potential limits caused by fiber fuse are discussed.
- 7 October 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (21) , 39086-39100
Spatiotemporal analysis of an all-fiber multimode interference-based saturable absorber via a mode-resolved nonlinear Schrodinger equation
This paper presents an approach that combines the generalized multimode nonlinear Schrodinger equation with a transmission model to analyze spatiotemporal characteristics of multimode interference in single mode/large mode area fiber–graded-index multimode fiber–single mode fiber (SMF/LMA-GIMF-SMF) structures for the first time. Approximated self-imaging (ASIM) behavior in GIMF and the study of the latter structure used in spatiotemporal mode-locked fiber lasers are first demonstrated. Simulations show that these structures can work as saturable absorbers enabling high-energy pulse output due to nonlinear intermodal interactions and intensity-dependent multimode interference. Otherwise, underlying ASIM is proven that it can perturb the transmission of SMF/LMA-GIMF-SMF, causing instability of their saturable-absorption characteristics. This paper provides a theoretical guide for many applications, such as beam shaping, mode conversion, and high-energy ultrafast fiber laser.
- 7 October 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (21) , 39086-39100
Spatiotemporal analysis of an all-fiber multimode interference-based saturable absorber via a mode-resolved nonlinear Schrodinger equation
This paper presents an approach that combines the generalized multimode nonlinear Schrodinger equation with a transmission model to analyze spatiotemporal characteristics of multimode interference in single mode/large mode area fiber–graded-index multimode fiber–single mode fiber (SMF/LMA-GIMF-SMF) structures for the first time. Approximated self-imaging (ASIM) behavior in GIMF and the study of the latter structure used in spatiotemporal mode-locked fiber lasers are first demonstrated. Simulations show that these structures can work as saturable absorbers enabling high-energy pulse output due to nonlinear intermodal interactions and intensity-dependent multimode interference. Otherwise, underlying ASIM is proven that it can perturb the transmission of SMF/LMA-GIMF-SMF, causing instability of their saturable-absorption characteristics. This paper provides a theoretical guide for many applications, such as beam shaping, mode conversion, and high-energy ultrafast fiber laser.
- Top Cited PapersOpen Access
- 17 March 2022
- Published by Springer Nature in Nature Communications
- Vol. 13 (1) , 1-8
All-fiber high-speed image detection enabled by deep learning
Ultra-high-speed imaging serves as a foundation for modern science. While in biomedicine, optical-fiber-based endoscopy is often required for in vivo applications, the combination of high speed with the fiber endoscopy, which is vital for exploring transient biomedical phenomena, still confronts some challenges. We propose all-fiber imaging at high speeds, which is achieved based on the transformation of two-dimensional spatial information into one-dimensional temporal pulsed streams by leveraging high intermodal dispersion in a multimode fiber. Neural networks are trained to reconstruct images from the temporal waveforms. It can not only detect content-aware images with high quality, but also detect images of different kinds from the training images with slightly reduced quality. The fiber probe can detect micron-scale objects with a high frame rate (15.4 Mfps) and large frame depth (10,000). This scheme combines high speeds with high mechanical flexibility and integration and may stimulate future research exploring various phenomena in vivo.
- 17 March 2022
- Published by Springer Nature in Nature Communications
- Vol. 13 (1) , 1-8
Top Cited PapersOpen AccessAll-fiber high-speed image detection enabled by deep learning
Ultra-high-speed imaging serves as a foundation for modern science. While in biomedicine, optical-fiber-based endoscopy is often required for in vivo applications, the combination of high speed with the fiber endoscopy, which is vital for exploring transient biomedical phenomena, still confronts some challenges. We propose all-fiber imaging at high speeds, which is achieved based on the transformation of two-dimensional spatial information into one-dimensional temporal pulsed streams by leveraging high intermodal dispersion in a multimode fiber. Neural networks are trained to reconstruct images from the temporal waveforms. It can not only detect content-aware images with high quality, but also detect images of different kinds from the training images with slightly reduced quality. The fiber probe can detect micron-scale objects with a high frame rate (15.4 Mfps) and large frame depth (10,000). This scheme combines high speeds with high mechanical flexibility and integration and may stimulate future research exploring various phenomena in vivo.
- 11 February 2022
- Published by Elsevier in Optics Communications
- Vol. 512
Thermal induced polarization coupling in double-cladding linearly polarized fiber lasers
- 11 February 2022
- Published by Elsevier in Optics Communications
- Vol. 512
Thermal induced polarization coupling in double-cladding linearly polarized fiber lasers
- 21 December 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (1) , 296-307
Spectral pedestal during the kilowatt-level amplification of a random fiber laser operating near the lasing threshold
The amplification of random fiber lasers (RFLs) attracts much attention due to their unique characteristics such as wavelength flexibility and low coherence. We present that, in the kilowatt-level amplification of RFL operating near its lasing threshold, a broad and flat spectral pedestal can co-exist with the narrow spectral peak of RFL. This phenomenon is different from the case in the amplification of fixed-cavity laser seeds. Time-domain measurements show that the broad and flat spectral pedestal, which extends to long wavelengths, is composed of temporal pulses, while few temporal pulses exist in the narrow spectral peak. We attribute the spectral pedestal to intensity fluctuations from the random seed laser and modulation instability in the amplification stage. Control experiments reveal that the working status of the random seed laser and the effective length of the amplifier can influence the spectral bandwidth. By taking advantage of this phenomenon, we propose a novel approach to achieve a high-power broadband light source through the amplification of RFLs operating near the lasing threshold.
- 21 December 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (1) , 296-307
Spectral pedestal during the kilowatt-level amplification of a random fiber laser operating near the lasing threshold
The amplification of random fiber lasers (RFLs) attracts much attention due to their unique characteristics such as wavelength flexibility and low coherence. We present that, in the kilowatt-level amplification of RFL operating near its lasing threshold, a broad and flat spectral pedestal can co-exist with the narrow spectral peak of RFL. This phenomenon is different from the case in the amplification of fixed-cavity laser seeds. Time-domain measurements show that the broad and flat spectral pedestal, which extends to long wavelengths, is composed of temporal pulses, while few temporal pulses exist in the narrow spectral peak. We attribute the spectral pedestal to intensity fluctuations from the random seed laser and modulation instability in the amplification stage. Control experiments reveal that the working status of the random seed laser and the effective length of the amplifier can influence the spectral bandwidth. By taking advantage of this phenomenon, we propose a novel approach to achieve a high-power broadband light source through the amplification of RFLs operating near the lasing threshold.
- Open Access
- 17 June 2021
- Published by Springer Nature in Research Square
All-fiber ultrafast image detection enabled by deep learning
Detection of dynamical scenes at ultrafast speeds serves as a foundation for modern engineering, chemistry, material science and biomedicine, et al. For biomedical applications, in vivo microscopic imaging is often required, which has led to the development of fiber-probe-based endoscopy. However, the combination of ultrafast image acquiring with fiber endoscopy has not yet been achieved, which is vital for exploration of transient biomedical phenomena. Here, we propose a scheme of all-fiber image detection at an ultrafast speed without any free-space optical elements. Image detection is achieved based on the transformation of two-dimensional spatial information into one-dimensional temporal pulsed signal streams by leveraging the high intermodal dispersion in a multimode fiber. Deep learning algorithms are subsequently deployed to reconstruct the images detected by the fiber probe from the temporal waveforms acquired at the other end of the fiber. The fiber probe can directly detect micron-scale objects without any bulk objective, and image detection has been experimentally realized with a high frame rate (15 Mfps), a large frame depth (104) and extremely short shutter time (30 ps) simultaneously. This ultrafast detection scheme, combined with high mechanical flexibility and high level of integration, can stimulate future research on exploring various in-vivo ultrafast phenomena.
- 17 June 2021
- Published by Springer Nature in Research Square
Open AccessAll-fiber ultrafast image detection enabled by deep learning
Detection of dynamical scenes at ultrafast speeds serves as a foundation for modern engineering, chemistry, material science and biomedicine, et al. For biomedical applications, in vivo microscopic imaging is often required, which has led to the development of fiber-probe-based endoscopy. However, the combination of ultrafast image acquiring with fiber endoscopy has not yet been achieved, which is vital for exploration of transient biomedical phenomena. Here, we propose a scheme of all-fiber image detection at an ultrafast speed without any free-space optical elements. Image detection is achieved based on the transformation of two-dimensional spatial information into one-dimensional temporal pulsed signal streams by leveraging the high intermodal dispersion in a multimode fiber. Deep learning algorithms are subsequently deployed to reconstruct the images detected by the fiber probe from the temporal waveforms acquired at the other end of the fiber. The fiber probe can directly detect micron-scale objects without any bulk objective, and image detection has been experimentally realized with a high frame rate (15 Mfps), a large frame depth (104) and extremely short shutter time (30 ps) simultaneously. This ultrafast detection scheme, combined with high mechanical flexibility and high level of integration, can stimulate future research on exploring various in-vivo ultrafast phenomena.
- 30 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 57 (2) , 1-9
5.1 kW Tandem-Pumped Fiber Amplifier Seeded by Random Fiber Laser With High Suppression of Stimulated Raman Scattering
In this work, high-power tandem-pumped random fiber lasers are investigated in detail. A 6.5 W random fiber laser seed centered at 1070 nm with a half-open cavity structure was built. Boosted by two amplifier stages, the random fiber laser achieved a power of several kilowatts. Stimulated Raman scattering (SRS) mitigation is challenging in tandem-pumped fiber lasers. To suppress SRS, several methods were applied, including avoiding external feedback in the oscillator stage, incorporating a high core/cladding diameter ratio gain fiber, and using a band pass filter (BPF) to mitigate Raman noise. The latter proved to be the most effective method; therefore, SRS mitigation without and with a BPF was investigated at 3.5 kW, leading to suppression ratios rising from 14 to 30 dB. By increasing the pump power continuously to 5.6 kW, we realized a record output power of 5.1 kW, corresponding to an SRS suppression ratio of 27 dB. Owing to the high-brightness 1018 nm fiber lasers serving as the pump sources and the high gain coefficient in the second amplifier stage, the entire system demonstrated high efficiency and stability. At the maximum power level, the total optical-to-optical efficiency reached 89.0%. This work offers an economic and practical technique for realizing high-power and high-efficiency random fiber lasers with effective SRS mitigation, while the experimental results suggest the potential for further power scaling.
- 30 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 57 (2) , 1-9
5.1 kW Tandem-Pumped Fiber Amplifier Seeded by Random Fiber Laser With High Suppression of Stimulated Raman Scattering
In this work, high-power tandem-pumped random fiber lasers are investigated in detail. A 6.5 W random fiber laser seed centered at 1070 nm with a half-open cavity structure was built. Boosted by two amplifier stages, the random fiber laser achieved a power of several kilowatts. Stimulated Raman scattering (SRS) mitigation is challenging in tandem-pumped fiber lasers. To suppress SRS, several methods were applied, including avoiding external feedback in the oscillator stage, incorporating a high core/cladding diameter ratio gain fiber, and using a band pass filter (BPF) to mitigate Raman noise. The latter proved to be the most effective method; therefore, SRS mitigation without and with a BPF was investigated at 3.5 kW, leading to suppression ratios rising from 14 to 30 dB. By increasing the pump power continuously to 5.6 kW, we realized a record output power of 5.1 kW, corresponding to an SRS suppression ratio of 27 dB. Owing to the high-brightness 1018 nm fiber lasers serving as the pump sources and the high gain coefficient in the second amplifier stage, the entire system demonstrated high efficiency and stability. At the maximum power level, the total optical-to-optical efficiency reached 89.0%. This work offers an economic and practical technique for realizing high-power and high-efficiency random fiber lasers with effective SRS mitigation, while the experimental results suggest the potential for further power scaling.
- 31 July 2020
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 37 (8) , 2514-2522
Suppressing the amplified spontaneous emission in the high-power 1018-nm monolithic fiber laser by decreasing the feedback from the inner reflections
We showed that decreasing the feedback that comes from the inner reflections of counter-propagating light could suppress the amplified spontaneous emission (ASE) in the output of 1018-nm fiber lasers. With a simulation model to solve the power spectrum of multiple signals, we calculated the values of the feedback required for aimed power scaling. We realized low feedback by modifying the counter-propagating side of the setup, which included a home-made cladding light stripper on a no-core fiber that was angle-cleaved. With that, we demonstrated a 1018-nm monolithic fiber laser producing 506.4 W with 1 .58 - M 2 beam quality, 84.9% optical–optical efficiency, and 148-pm linewidth. The maximum intensity of the ASE noises was > 50 d B lower than that of the 1018-nm signal, which could allow further power scaling with safety and stability.
- 31 July 2020
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 37 (8) , 2514-2522
Suppressing the amplified spontaneous emission in the high-power 1018-nm monolithic fiber laser by decreasing the feedback from the inner reflections
We showed that decreasing the feedback that comes from the inner reflections of counter-propagating light could suppress the amplified spontaneous emission (ASE) in the output of 1018-nm fiber lasers. With a simulation model to solve the power spectrum of multiple signals, we calculated the values of the feedback required for aimed power scaling. We realized low feedback by modifying the counter-propagating side of the setup, which included a home-made cladding light stripper on a no-core fiber that was angle-cleaved. With that, we demonstrated a 1018-nm monolithic fiber laser producing 506.4 W with 1 .58 - M 2 beam quality, 84.9% optical–optical efficiency, and 148-pm linewidth. The maximum intensity of the ASE noises was > 50 d B lower than that of the 1018-nm signal, which could allow further power scaling with safety and stability.
- 3 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (10) , 573-576
An Efficient Non-Invasive Method to Fabricate In-Fiber Microcavities Using a Continuous-Wave Laser
In-fiber microcavities are usually fabricated by inva-sive methods that require costly setups and time-consuming processes. Inspired by the fiber fuse effect, we propose an efficient non-invasive method to fabricate in-fiber microcavities. The setup of the method was economic, using a watt-level continuous-wave laser. Spherical in-fiber microcavities of ~hundred-of-micron sizes could be fabricated and freely integrated in fibers. The fabrication rate was seconds-per-microcavity, being hundreds of times faster than previous methods. The microcavities could have ~1-micron-thin cavity walls and ~104 high quality factors as Fabry-Perot reso-nators. The method offers many unique features for microcavities and can be useful for large-scale fabrication. It can benefit many applications such as sensing and nonlinear frequency generation
- 3 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (10) , 573-576
An Efficient Non-Invasive Method to Fabricate In-Fiber Microcavities Using a Continuous-Wave Laser
In-fiber microcavities are usually fabricated by inva-sive methods that require costly setups and time-consuming processes. Inspired by the fiber fuse effect, we propose an efficient non-invasive method to fabricate in-fiber microcavities. The setup of the method was economic, using a watt-level continuous-wave laser. Spherical in-fiber microcavities of ~hundred-of-micron sizes could be fabricated and freely integrated in fibers. The fabrication rate was seconds-per-microcavity, being hundreds of times faster than previous methods. The microcavities could have ~1-micron-thin cavity walls and ~104 high quality factors as Fabry-Perot reso-nators. The method offers many unique features for microcavities and can be useful for large-scale fabrication. It can benefit many applications such as sensing and nonlinear frequency generation
- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (9) , 518-521
1535–1620 nm Widely Tunable Watt-Level Single-Mode Er:Yb Codoped All-Fiber MOPA
We report a continuous-wave 1535-1620 nm widely tunable single-mode Er:Yb codoped cladding-pumped all-fiber laser source based on the MOPA scheme. The output power ranged from 0.785 W (at 1615 nm) to 2.007 W (at 1565 nm), which is the highest output power from a C+L tunable all-fiber laser source. The 3 dB spectral width was less than 150 pm at all wavelengths. No Yb emission was observed. We proposed a mid-way backward pumping configuration in which the pump light was injected between two gain fibers and propagated backward to broaden the effective wavelength range of the fiber amplifier. Experiments verified the capability of our configuration to improve the suppression ratio of C-band amplified spontaneous emissions from 13 dB to 35 dB when the signal laser was operating at 1620 nm.
- 23 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (9) , 518-521
1535–1620 nm Widely Tunable Watt-Level Single-Mode Er:Yb Codoped All-Fiber MOPA
We report a continuous-wave 1535-1620 nm widely tunable single-mode Er:Yb codoped cladding-pumped all-fiber laser source based on the MOPA scheme. The output power ranged from 0.785 W (at 1615 nm) to 2.007 W (at 1565 nm), which is the highest output power from a C+L tunable all-fiber laser source. The 3 dB spectral width was less than 150 pm at all wavelengths. No Yb emission was observed. We proposed a mid-way backward pumping configuration in which the pump light was injected between two gain fibers and propagated backward to broaden the effective wavelength range of the fiber amplifier. Experiments verified the capability of our configuration to improve the suppression ratio of C-band amplified spontaneous emissions from 13 dB to 35 dB when the signal laser was operating at 1620 nm.