TOToshihiro Ohki

Toshihiro Ohki

*This is an algorithmically generated author record based on publicly available information.

Toshihiro Ohki has a total of 51 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Methodology for determining interface-state density in AlGaN/GaN MIS-HEMT structures using sub-bandgap illumination

    by Maciej Matys, Yoichi Kamada, Atsushi Yamada, Toshihiro Ohki

    In this work, we present a methodology for determining the interface-state density distribution in metal–insulator–semiconductor (MIS) AlGaN/GaN heterostructures using sub-bandgap illumination. First, we discuss the electronic transitions that occur during sub-bandgap illumination of MIS AlGaN/GaN heterostructures. In particular, we show how these transitions can induce a threshold-voltage shift in MIS AlGaN/GaN high electron mobility transistor structures and, consequently, lead to a completely erroneous interpretation of the results. In this context, we experimentally demonstrate that the interface-state density distribution can be significantly overestimated due to, for example, free-hole generation resulting from electronic transitions via interface states at the AlGaN/insulator interface and/or deep levels in the GaN buffer layer. Finally, we provide guidelines for the accurate determination of the interface-state density in MIS AlGaN/GaN heterostructures using sub-bandgap illumination, including detailed measurement and analysis procedures.

  • Open Access

    GaN-based MIS HEMT with SiAlN gate dielectric achieving over 70% PAE and 10 W mm −1 at 8 GHz

    by Yuichi Minoura, Atsushi Yamada, Kenji Saito, Norikazu Nakamura, Toshihiro Ohki

    We achieved a simultaneous record-high power-added efficiency (PAE) of 71.4% and an output power density of 10.4 W mm −1 at 8 GHz in an AlGaN/GaN metal-insulator-semiconductor (MIS) high-electron-mobility transistor (HEMT) on a free-standing GaN substrate, utilizing SiAlN as the gate dielectric. This exceptional performance stems from the high quality of the metal-organic chemical vapor deposited SiAlN gate dielectric and the gate field plate structure employing a SiN/SiAlN stack, enabling the combined realization of high output power and efficiency. These results emphatically demonstrate the significant potential of MIS gate structures for advanced microwave power amplifiers across various applications.

  • Open Access

    A simple method for detection and quantitative estimation of deep levels in a barrier layer of AlGaN/GaN HEMT structures by analysis of light induced threshold voltage shift

    by Maciej Matys, Atsushi Yamada, Yoichi Kamada, Toshihiro Ohki

    The characterization of deep levels in AlGaN/gallium nitride (GaN) heterostructures is one of the most important problems in GaN high electron mobility transistor (HEMT) technology. This work reports on a technique for determination of deep level concentration in AlGaN/GaN HEMT structures. The proposed method is relatively simple, and it is based on the detection of free holes created by optically induced transitions of electrons from the deep levels to the conduction band. The developed method can detect and provide quantitative estimation of deep level traps in a barrier layer of AlGaN/GaN HEMT structures. Furthermore, it provides a framework for analysis of light induced threshold voltage shift, which includes an important experimental criterion of determination whether the holes are generated or not in the AlGaN/GaN HEMT structures by subbandgap illumination. The method was verified by applying it to a study of the deep levels in GaN HEMTs grown on various substrates, i.e., SiC and GaN.


  • Open Access

    Effects of indium within a barrier on the gate leakage current in an InAlGaN/GaN high-electron-mobility transistor

    by Atsushi Yamada, Toshihiro Ohki

    We investigated the impact of In within barriers on the gate leakage current in InAlGaN/GaN high-electron-mobility transistors (HEMTs). The results revealed that the gate leakage current in the (In)AlGaN barriers depends solely on the two-dimensional electron gas density, regardless of the presence of In atoms. Furthermore, the inclusion of In atoms reduces tensile strain within the high-Al-composition barrier, suppressing crack formation. This makes InAlGaN suitable for high-output-power HEMTs with high-Al-content barriers. Moreover, we demonstrate that the terminating dislocations using an AlN spacer and an amorphous AlN cap are an effective method for suppressing the gate leakage current in InAlGaN/GaN HEMTs.


  • Top Cited Papers
    Open Access

    AlGaN/GaN HEMT on a free-standing GaN substrate with record 85.2% power-added efficiency at 2.45 GHz

    by Toshihiro Ohki, Atsushi Yamada, Yuichi Minoura, Yusuke Kumazaki, Kenji Saito, Masaru Sato

    An AlGaN/GaN high-electron-mobility transistor (HEMT) on a free-standing GaN substrate achieved impressive power-added and drain efficiencies of 85.2% and 89.0%, respectively, at 2.45 GHz. We improved the GaN channel quality by reducing the C concentration and eliminated the buffer leakage path by removing the residual Si at the substrate-epitaxial layer interface. These improvements, combined with the reduction in dislocation density and the elimination of the nucleation layer by using a free-standing GaN substrate, contributed to the enhanced efficiency. To the best of our knowledge, the achieved efficiency represents the highest reported for GaN-based discrete HEMTs in this frequency band.


  • 37.1-dBm W-Band Power Amplifier Module Using GaN-Based HEMTs Stabilized With Resistive Back Metal for Broadband Wireless Applications

    by Yasuhiro Nakasha, Yusuke Kumazaki, Shiro Ozaki, Naoya Okamoto, Naoki Hara, Atsushi Yamada, Toshihiro Ohki

    This letter presents a four-way W-band power amplifier (PA) module that packages GaN-based high electron mobility transistor (HEMT) millimeter-wave monolithic integrated circuits (MMICs) designed with coplanar waveguides (CPWs). A resistive-back-metal (RBM) layer was formed on the back side of the MMICs to keep stable in the module even without using substrate vias. The verification of the effect of the RBM layer was performed using CPW-based MMIC test chips. The assembled PA module, where millimeter-wave components, such as a waveguide (WG) combiner/divider and a WG-to-microstrip line transition, were optimized to reduce losses and flatten frequency responses, demonstrated stable and broadband characteristics in a frequency range of 88–100 GHz. A peak output power (POUT) of 37.1 dBm with a power-added efficiency (PAE) of 9.9% was achieved at a frequency of 92 GHz and a bias voltage (VDS) of 15 V. VDS was set to 20 V to enhance the power performance of the PA module, achieving a peak POUT of 38.8 dBm with a PAE of 8.1%. To the best of our knowledge, the PA module exhibited the highest peak POUT value among W-band single PA modules with a bandwidth (BW) of more than 10 GHz.


  • 31 W/mm at 8 GHz in InAlGaN/GaN HEMT With Thermal CVD SiNx Passivation

    by Atsushi Yamada, Yuichi Minoura, Naoko Kurahashi, Yoichi Kamada, Toshihiro Ohki, Masaru Sato, Norikazu Nakamura

    The study reports the findings on a quaternary InAlGaN/GaN high electron mobility transistor (HEMT) employing a thermal chemical vapor deposition (TCVD) silicon nitride (SiN x ) passivation with a record high output power density of 31.0 W/mm in the X-band. We compared the two different SiN x passivation methods, namely, TCVD deposition, and plasma-enhanced CVD (PECVD) deposition, for InAlGaN/GaN HEMTs and investigated the effects on device performance. PECVD SiN x passivation caused a considerable degradation of the two-dimensional electron gas (2DEG) mobility. However, TCVD SiN x could suppress the degradation of 2DEG mobility, resulting in a low sheet resistance of 293 ohm/sq. with a high 2DEG mobility of 2048 cm 2 V -1 s -1 . Furthermore, InAlGaN/GaN HEMT with TCVD SiN x passivation exhibited a high-drain current of 1230 mA/mm even after off-state stress due to the reduced current collapse and low sheet resistance. The off-state breakdown voltage increased from 169 to 227 V on using TCVD SiN x despite an increase in the maximum drain current, resulting in a high voltage of 90 V at radiofrequency. We successfully demonstrated the state-of-the-art high output power density GaN-based HEMTs with an InAlGaN barrier and TCVD SiN x passivation. Our results revealed that TCVD SiN x passivation can facilitate the application of InAlGaN/GaN HEMTs for high-power amplifiers.


  • Open Access

    24.4 W/mm X-Band GaN HEMTs on AlN Substrates With the LPCVD-Grown High-Breakdown-Field SiN x Layer

    by Junji Kotani, Junya Yaita, Kenji Homma, Shirou Ozaki, Atsushi Yamada, Masaru Sato, Toshihiro Ohki, Norikazu Nakamura

    This paper reports on an AlGaN/GaN high-electron-mobility transistor (HEMT) on free-standing AlN substrates with a record-high output power density of 24.4 W/mm at the X-band. A high-drain current operation of 1.4 A/mm was realized by employing high-density 2-dimensional electron gas channel and regrown Ohmic contacts. Furthermore, a high-voltage operation of 110 V was achieved owing to the high-density and high-breakdown SiNx layer grown by low-pressure/high-temperature chemical vapor deposition. Three-stage AlGaN buffer layers improved the electron mobility of 2-dimensional electron gas and allowed us to grow a GaN channel with a low carbon concentration. Furthermore, a regrown n-GaN contact layer was employed to minimize source/drain contact resistances. A high drain current of 1470 mA/mm and high breakdown voltage of 258 V were achieved. Our results demonstrate the potential of GaN HEMTs on the AlN substrate as next-generation high-power radio frequency devices.


  • Low-Resistance and Low-Thermal-Budget Ohmic Contact by Introducing Periodic Microstructures for AlGaN/AlN/GaN HEMTs

    by Yusuke Kumazaki, Shiro Ozaki, Naoya Okamoto, Naoki Hara, Toshihiro Ohki

    In this study, we proposed a low-resistance and low-thermal-budget ohmic contact by introducing periodic microstructures for AlGaN/AlN/GaN high-electron-mobility transistors (HEMTs). Insertion of AlN spacer layers is effective in improving electron mobility but can degrade contact resistance, in general. An ohmic contact with periodic microstructures was fabricated through low-damage patterned recess etching and metallization via low-temperature annealing (600 °C). The optimization of structural parameters of periodic microstructures allowed a low contact resistance of 0.29 $\Omega \cdot $ mm, which is less than half of that of the conventional recessed ohmic contact prepared in this study. A simplified equivalent circuit model reproduced the experimental results and predicted that enhanced metal/channel direct contact areas contributed to the reduction of contact resistance. Pulsed current–voltage measurements revealed that an AlGaN/AlN/GaN HEMT with periodic microstructures showed considerably suppressed current collapse compared with that of a selective-area growth (SAG) ohmic contact, indicating that the introduction of trap states was suppressed in periodic-structured devices owing to low-thermal-budget processes. Under high off-stress conditions, periodic-structured devices showed the highest drain current at knee voltage compared to the devices with a conventional planar-recessed ohmic contact and an SAG ohmic contact. Therefore, ohmic contact with periodic microstructures is one of the best techniques to achieve low contact resistance with low-thermal-budget processes.


  • Deep GaN through-substrate via etching using Cl2/BCl3 inductively coupled plasma

    by Naoya Okamoto, Atsushi Takahashi, Yuichi Minoura, Yusuke Kumazaki, Shiro Ozaki, Toshihiro Ohki, Naoki Hara, Keiji Watanabe

    In this study, the etching characteristics for fabricating deep GaN through-substrate vias at a high etching rate exceeding 1 μm/min using high density Cl2/BCl3 inductively coupled plasma were investigated. The etching rate decreased almost linearly with increasing BCl3 content up to a 25% gas mixture ratio; however, an etching rate of more than 1 μm/min was achieved. The highest GaN/Ni metal mask etching selectivity was obtained at the gas mixture ratio of 10%. However, large pillars were formed in almost all the via holes, which was attributed to the wafer temperature during etching. By optimizing the etching conditions, GaN via holes with depths of 91 μm and diameters of 80 μm without pillars were successfully formed at an etching rate as high as 1.5 μm/min and with an etching selectivity as high as 35. Furthermore, it was clarified that the etch-back of the Ni metal mask produced sidewalls with two different slopes in these via holes.