NPNathaniel T. Pickle

Nathaniel T. Pickle

*This is an algorithmically generated author record based on publicly available information.

Nathaniel T. Pickle has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The impact of a commercial lower extremity exoskeleton on metabolic load, perceived exertion, and physiological response to a challenging military relevant task: A randomized cross-over design pilot study

    by JoEllen M. Sefton, Frances K. Neal, Philip J. Agostinelli, Nicholas C. Bordonie, Phillip E. Whitley, Nathan T. Pickle, Paulien E. Roos

    Purpose: To assess physiological metrics during the use of a commercially available bilateral active ankle exoskeleton during a challenging military-relevant task and if use of the exoskeleton during this task influences: metabolic load, physiological measures or rate of perceived exertion. Methods: Nine healthy volunteers (5M, 4F) completed this randomized cross-over design trial, with a baseline visit and two randomized test sessions (with/without the exoskeleton). Variables included impact on time to exhaustion during walking on a treadmill at varying speeds and gradients (0–15%) at 26.7°C, 50% humidity with a loaded rucksack (30% body weight). The primary outcome measure was change in metabolic cost with/without the exoskeleton (O2 consumption, metabolic equivalents); secondary outcomes were change in heart rate and perceived exertion between conditions. Results: Participants averaged 22.4 ± 4.5 years old, 173.7 ± 7.4 cm tall, weighed 80.9 ± 13.9 kg, and VO2max of 43.8 ± 10.6 mL/kg/min. Total kcals did not differ between conditions (with/without exoskeleton; t = 0.98; p = 0.357). Kcals/min were significantly lower (1.06 kcals/min) with the exoskeleton (t = 3.94; p = 0.004). Average oxygen consumption (VO2) was significantly lower (2.36 mL/kg/min) with the exoskeleton (t = 2.81; p = 0.023), and peak VO2 was 3.33 mL/kg/min lower with the exoskeleton (t = 2.37; p = 0.045). Peak and Average METS were also lower with the exoskeleton by 0.98 (t = 2.61; p = 0.031) and 1.23 (t = 2.39; p = 0.044) respectively. Conclusions: Results suggest a powered ankle exoskeleton may decrease energy consumption during military relevant tasks when conducted in a laboratory environment. There may also be physiological benefits such as reduced core temperate and heart rate. Replication of this work in the field environment is warranted.


  • Generation of Warfighter Avatars from Weapon Training Scene Images for Blast Exposure Simulations

    by Harsha T. Garimella, Nathan Pickle, Garrett Tuer, Josh Hogue, Paulien E. Roos, Raj K. Gupta, Andrzej J. Przekwas

    Military personnel involved in weapon training are subjected to repeated low-level blasts. The prevailing method of estimating blast loads involves wearable blast gauges. However, using wearable sensor data, blast loads to the head or other organs cannot be accurately estimated without knowledge of the service member's body posture. An image/video-augmented complementary experimental-computational platform for conducting safer weapon training was developed. This study describes the protocol for the automated generation of weapon training scenes from video data for blast exposure simulations. The blast scene extracted from the video data at the instant of weapon firing involves the service member body avatars, weapons, ground, and other structures. The computational protocol is used to reconstruct service members' positions and postures using this data. Image or video data extracted from service member body silhouettes are used to generate an anatomical skeleton and the key anthropometric data. These data are used to generate the 3D body surface avatars segmented into individual body parts and geometrically transformed to match extracted service member postures. The final virtual weapon training scene is used for 3D computational simulations of weapon blast wave loading on service members. The weapon training scene generator has been used to construct 3D anatomical avatars of individual service member bodies from images or videos in various orientations and postures. Results of the generation of a training scene from shoulder-mounted assault weapon system and mortar weapon system image data are presented. The Blast Overpressure (BOP) tool uses the virtual weapon training scene for 3D simulations of blast wave loading on the service member avatar bodies. This paper presents 3D computational simulations of blast wave propagation from weapon firing and corresponding blast loads on service members in training.

  • Open Access

    Predictive simulation of human movement in OpenSim using floating-base task space control

    by Nathaniel T. Pickle, Aravind Sundararajan

    Task space control, also known as operational space control, is a useful paradigm for investigating neural control of human movement using predictive simulations. While some efforts have been made to implement task space control in the widely used open-source platform OpenSim, existing implementations do not support floating base kinematics, which is necessary for simulating gait and other types of human movement. Our aim in this work is to fill that gap. In this paper, we describe the theory and implementation of a floating base kinematics task space framework for torque- and muscle-driven simulations in OpenSim. Our framework builds on previous work that was limited to models with a base (i.e., root) segment fixed to ground. In addition, we integrate various algorithms from robotics in order to handle dynamically changing contacts and task prioritization. The framework can be used to generate realistic walking gaits by prescribing a small set of controller gains and gait parameters such as step length, step width and center of mass velocity. Task can be specified as desired positions, rotations, or higher-order feature such as base of support and whole-body angular momentum. We provide several examples to demonstrate how framework is successful in orchestrating a complex hierarchy of tasks that work in concert to perform both balance control and gait generation. The implementation is freely available for roboticists and biomechanists to use with OpenSim. Author summary Recent advances in computational biomechanics have provided researchers with tools capable of predicting human movement. Previous approaches to simulating human movement required experimental data as input and the simulation would replicate the experimental motion. This conventional approach limited the scientific insights to the specific movement recorded in the laboratory. With predictive approaches, researchers can investigate how a person might respond to various factors, such as reduced muscle strength or an assistive device such as a robotic exoskeleton. Existing approaches for generating predictive simulations utilize optimization-based approaches, which can be time-consuming and difficult to troubleshoot. Task space control is an alternative approach which is widely used in robotics. Conceptually, task space control aims to generate a simulation by specifying “tasks”, such as moving a hand or foot to a desired position, and computing the joint angles required to achieve the task. Here we aim to outline the mathematics behind task space control and demonstrate how task space control can be used to generate simulations of movements such as walking.

  • Open Access

    Automated Optimization of Residual Reduction Algorithm Parameters in Opensim

    by Jordan T. Sturdy, Anne K. Silverman, Nathan T. Pickle

    The residual reduction algorithm (RRA) in OpenSim is designed to improve dynamic consistency of kinematics and ground reaction forces in movement simulations of musculoskeletal models. RRA requires the user to select numerous tracking weights for the joint kinematics to reduce residual errors. Selection is often performed manually, which can be time-consuming and is unlikely to yield optimal tracking weights. A multi-heuristic optimization algorithm was used to expedite tracking weight decision making to reduce residual errors. This method produced more rigorous results than manual iterations and although the total computation time was not significantly reduced, this method does not require the user to monitor the algorithm’s progress to find a solution, thereby reducing manual tuning. Supporting documentation and code to implement this optimization is freely provided to assist the community with developing movement simulations.


  • Open Access

    Dynamic neural network approach to targeted balance assessment of individuals with and without neurological disease during non-steady-state locomotion

    by Nathaniel T. Pickle, Staci M. Shearin, Nicholas P. Fey

    Clinical balance assessments often rely on functional tasks as a proxy for balance (e.g., Timed Up and Go). In contrast, analyses of balance in research settings incorporate quantitative biomechanical measurements (e.g., whole-body angular momentum, H) using motion capture techniques. Fully instrumenting patients in the clinic is not feasible, and thus it is desirable to estimate biomechanical quantities related to balance from measurements taken from a subset of the body segments. Machine learning algorithms are well-suited for this type of low- to high-dimensional mapping. Thus, our goal was to develop and test an artificial neural network that to predict segment contributions to whole-body angular momentum from linear acceleration and angular velocity signals (i.e., those typically available to wearable inertial measurement units, IMUs) taken from a sparse set of body segments. Optical motion capture data were collected from five able-bodied individuals and five individuals with Parkinson's disease (PD) walking on a non-steady-state locomotor circuit comprising stairs, ramps and changes of direction. Motion data were used to calculate angular momentum (i.e., “gold standard” output data) and body-segment linear acceleration and angular velocity data from local reference frames at the wrists, ankles and neck (i.e., network input). A dynamic nonlinear autoregressive neural network was trained using the able-bodied data (pooled across subjects). The neural network was tested on data from individuals with PD with noise added to simulate real-world IMU data. Correlation coefficients of the predicted segment contributions to whole-body angular momentum with the gold standard data were 0.989 for able-bodied individuals and 0.987 for individuals with PD. Mean RMS errors were between 2 and 7% peak signal magnitude for all body segments during completion of the locomotor circuits. Our results suggest that estimating segment contributions to angular momentum from mechanical signals (linear acceleration, angular velocity) from a sparse set of body segments is a feasible method for assessing coordination of balance—even using a network trained on able-bodied data to assess individuals with neurological disease. These targeted estimates of segmental momenta could potentially be delivered to clinicians using a sparse sensor set (and likely in real-time) in order to enhance balance rehabilitation of people with PD.


  • Open Access

    Statistical analysis of timeseries data reveals changes in 3D segmental coordination of balance in response to prosthetic ankle power on ramps

    by Nathaniel T. Pickle, Anne K. Silverman, Jason M. Wilken, Nicholas P. Fey

    Active ankle-foot prostheses generate mechanical power during the push-off phase of gait, which can offer advantages over passive prostheses. However, these benefits manifest primarily in joint kinetics (e.g., joint work) and energetics (e.g., metabolic cost) rather than balance (whole-body angular momentum, H), and are typically constrained to push-off. The purpose of this study was to analyze differences between active and passive prostheses and non-amputees in coordination of balance throughout gait on ramps. We used Statistical Parametric Mapping (SPM) to analyze time-series contributions of body segments (arms, legs, trunk) to three-dimensional H on uphill, downhill, and level grades. The trunk and prosthetic-side leg contributions to H at toe-off when using the active prosthesis were more similar to non-amputees compared to using a passive prosthesis. However, using either a passive or active prosthesis was different compared to non-amputees in trunk contributions to sagittal-plane H during mid-stance and transverse-plane H at toe-off. The intact side of the body was unaffected by prosthesis type. In contrast to clinical balance assessments (e.g., single-leg standing, functional reach), our analysis identifies significant changes in the mechanics of segmental coordination of balance during specific portions of the gait cycle, providing valuable biofeedback for targeted gait retraining.


  • Open Access

    A comparison of stability metrics based on inverted pendulum models for assessment of ramp walking

    by Nathaniel T Pickle, Jason M Wilken, Nicholas P Fey, Anne K Silverman

    Maintaining balance on ramps is important for mobility. However, balance is commonly assessed using inverted pendulum-based metrics (e.g., margin of stability), which may not be appropriate for assessment of human walking on non-level surfaces. To investigate this, we analyzed stability on ramps using four different inverted pendulum models: extrapolated center of mass (XCOM), foot placement estimate (FPE), foot placement estimate neglecting angular momentum (FPENoH), and capture point (CAP). We analyzed experimental data from 10 able-bodied individuals walking on a ramp at 0°, ±5°, and ±10°. Contrary to our hypothesis that the magnitude of differences between metrics would be greatest at ±10°, we observed the greatest magnitude of differences between metrics at 0°. In general, the stability metrics were bounded by FPE and CAP at each slope, consistent with prior studies of level walking. Our results also suggest that clinical providers and researchers should be aware that assessments that neglect angular momentum (e.g., margin of stability, XCOM) may underestimate stability in the sagittal-plane in comparison to analyses which incorporate angular momentum (e.g., FPE). Except for FPENoH-CAP (r = 0.82), differences between metrics were only moderately correlated (|r|≤0.65) with violations of leg length assumptions in the underlying inverted pendulum models. The differences in FPENoH relative to FPE and CAP were strongly correlated with body center of mass vertical velocity (max |r| = 0.92), suggesting that model representations of center of mass motion influence stability metrics. However, there was not a clear overall relationship between model inputs and differences in stability metrics. Future sensitivity analyses may provide additional insight into model characteristics that influence stability metrics.


  • Open Access

    The Functional Roles of Muscles, Passive Prostheses, and Powered Prostheses During Sloped Walking in People With a Transtibial Amputation

    by Nathaniel T. Pickle, Alena M. Grabowski, Jana R. Jeffers, Anne K. Silverman

    Sloped walking is challenging for individuals with transtibial amputation (TTA) due to the functional loss of the ankle plantarflexors. Prostheses that actively generate ankle power may help to restore this lost function. The purpose of this study was to use musculoskeletal modeling and simulation to quantify the mechanical power delivered to body segments by passive and powered prostheses and the remaining muscles in the amputated and intact legs during sloped walking. We generated walking simulations from experimental kinematic and kinetic data on slopes of 0, ±3 deg and ±6 deg in eight people with a TTA using powered and passive prostheses and eight nonamputees. Consistent with our hypothesis, the amputated leg hamstrings generated more power to both legs on uphill slopes in comparison with nonamputees, which may have implications for fatigue or overuse injuries. The amputated leg knee extensors delivered less power to the trunk on downhill slopes (effect size (ES) ≥ 1.35, p ≤ 0.02), which may be due to muscle weakness or socket instability. The power delivered to the trunk from the powered and passive prostheses was not significantly different (p > 0.05), However, using the powered prosthesis on uphill slopes reduced the contributions from the amputated leg hamstrings in all segments (ES ≥ 0.46, p ≤ 0.003), suggesting that added ankle power reduces the need for the hamstrings to compensate for lost ankle muscle function. Neither prosthesis replaced gastrocnemius function to absorb power from the trunk and deliver it to the leg on all slopes.


  • Segmental contributions to sagittal-plane whole-body angular momentum when using powered compared to passive ankle-foot prostheses on ramps

    by Nathaniel T. Pickle, Anne K. Silverman, Jason M. Wilken, Nicholas P. Fey

    Understanding the effects of an assistive device on dynamic balance is crucial, particularly for robotic leg prostheses. Analyses of dynamic balance commonly evaluate the range of whole-body angular momentum (H). However, the contributions of individual body segments to overall H throughout gait may yield futher insights, specifically for people with transtibial amputation using powered prostheses. We evaluated segment contributions to H using Statistical Parametric Mapping to assess the effects of prosthesis type (powered vs passive) and ramp angle on segmental coordination. The slope main effect was significant in all segments, the prosthesis main effect was significant in the prosthetic leg (device and residuum) and trunk, and the slope by prosthesis interaction effect was significant in the prosthetic leg and trunk. The magnitude of contributions to sagittal-plane H from the prosthetic leg was larger when using the powered prosthesis. The trunk contributed more positive (backward) H after prosthetic leg toe-off when using the powered prosthesis on inclines, similar to the soleus muscle. However, trunk contributions to H on declines were similar when using a powered and passive prosthesis, suggesting that the powered prosthesis may not replicate soleus function when walking downhill. Our novel assessment method evaluated robotic leg prostheses not only based on local joint mechanics, but also considering whole-body biomechanics.