OVOleg Yu. Vorobiev

Oleg Yu. Vorobiev

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Oleg Yu. Vorobiev has a total of 73 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A wide-range thermodynamically consistent constitutive model for dynamic loading of partially saturated porous media

    by Oleg Vorobiev

    SUMMARY: This paper presents a novel thermodynamically consistent constitutive model for partially saturated porous rocks across a wide range of conditions. The material states generated behind the shock wave from an explosive source can vary significantly, ranging from crushed and melted rock near the source to a poroelastic medium in the far field. In the model, rock strength is determined by the effective pressure, which is calculated using two independent equations of state: one for the solid rock and another for the pore fluid. The model accounts for shock-induced liquefaction resulting from fluid pressure buildup in the pore spaces near the explosive source. Simultaneously, it describes the increase in wave propagation speed due to elastic pore contraction in both dry and partially saturated rocks. This model is applied to investigate how fluid saturation affects the amplitude and shape of the generated waves, as well as the residual stress surrounding the cavity formed by spherical explosions.


  • Airblast observations and near-field modeling of the large surface explosion coupling experiment

    by Oleg Vorobiev, Sean Ford

    Seismoacoustic wave generation for two consecutive surface chemical explosions of the same yield (approximately 1 ton TNT-equivalent) was studied during the Large Surface Explosion Coupling Experiment (LSECE) conducted at Yucca Flat on the Nevada National Security Site (NNSS) site in alluvium geology. We have performed numerical simulations for both chemical explosions to investigate how the non-central source initiation, site topography and soil mechanical properties affect the evolution of the explosion (fireball and cloud), its crater, and variations in the generated blast waves. The results can be used to improve the understanding of surface explosions and their effects and how those effects can be used to infer source information such as explosive yield and emplacement. We find that the non-central detonation of the explosive cube results in non-axisymmetric blast overpressures which persist through the strong and weak shock regimes, in this case out to 200 m and more. The pattern of the secondary shock (i.e., shock created due to slowing explosive products within the expanding fireball) is also affected and its arrival relative to the main shock and may be indicative of explosive type due to its dependence on the explosive products ratio of heats. Small reflections are visible within the overpressure signal that are most probably due to small artifacts in blast path. Importantly, the fireball growth, cavity generation, and cloud formation also depart from spherical and ideal approximations due to ground interactions and material dependence, which shows the importance of realistic geomaterial models for accurate prediction. The asymmetry in peak overpressure is diminished for the second chemical explosion, which was placed in the crater of the first. Numerical modeling shows that the explosive jetting created by the non-central detonation is reduced upon interaction with the crater walls and this has the effect of making the blast generation more axisymmetric.


  • Open Access

    A study of explosive-induced fracture in polymethyl methacrylate (PMMA)

    by S. M. Torres, O. Y. Vorobiev, R. E. Robey, M. J. Hargather

    The fracture response of geologic materials is of interest for applications, including geothermal energy harnessing and containment of underground explosions. To better understand the explosively induced fracture response of geomaterials, polymethyl methacrylate (PMMA) was used as a transparent rock surrogate to allow imaging of internal shock propagation and fracture growth processes. Experiments were conducted using high-speed shadowgraphy and photon Doppler velocimetry (PDV), which were compared to numerical simulations. Experiments measured fractures produced in 304.8mm×304.8mm×304.8mm PMMA cubes with two simultaneously initiated detonators. The cubes were subjected to varying amounts and directions of externally applied uniaxial stresses, including no stress, 2 MPa stress, and 20 MPa stress. The fracture radius as a function of time was extracted from the high-speed videos. Post-test images of the PMMA cubes aided in the determination of three-dimensional effects not directly imaged by the cameras. The surface velocity history and the shock response captured in PDV and the high-speed videos were compared to the simulated explosive-induced shock response. The simulation results indicate that the shock drives the fracture for the first 20 μs corresponding to a fracture radius of approximately 15 mm in the experiments. The gas-driven fracture extent was estimated analytically using an equilibrium stress distribution calculated after the shock wave propagation through the sample. Reduction in the gas pressure due to the leakage of the explosive products through the crack as a function of time was accounted for. The estimated fracture lengths were in agreement with the experimentally observed fracture lengths.


  • On various mechanisms of shear wave generation from underground chemical explosions in hard rocks

    by Oleg Vorobiev

    SUMMARY: Significant shear waves observed during underground explosions can make them look similar to natural earthquakes. In the near field, they can be caused by the source geometry and emplacement conditions, heterogeneous and anisotropic properties of the rock mass, relaxation of a non-uniform in situ stress around the source after the departure of the shock wave as well as by activation of nearby faults. The stress relaxation mechanism is important at depth when the difference in main principal stresses becomes significant. Another mechanism of shear motion generation is due to explosive gas flow from the source cavity into the cracks initiated by the shock wave and joints connected to the cavity. Also, the shock wave from the explosion can cause weakening of the rock either due to permanent damage or shock-induced liquefaction at saturated joints. Numerical modelling of underground chemical explosions in hard rock at various confinement stresses has been conducted to compare various mechanisms of shear wave generation and their seismic characteristics with that of a simple fault rupture process observed during an earthquake.


  • COMPUTER SIMULATION OF HYPERVELOCITY IMPACT AND ASTEROID EXPLOSION

    by A. V. Bushman, A. M. Vickery, V. E. Fortov, B. P. Krukov, I. V. Lomonosov, S. A. Medin, A. L. NI, A. V. Shutov, O. Yu. Vorobiev

    JSTOR is a digital library of academic journals, books, and primary sources.

  • Interface and embedded joint methods for modeling dynamic fracture opening by explosive products

    by Oleg Y. Vorobiev, Randolph Settgast, Joseph P. Morris

    Summary: Two computational approaches are proposed in the paper to model dynamic fracture opening by explosive products. The first method assumes that the fractures may be modeled using flow elements embedded along the mesh lines. This method models crack opening in a straightforward way by splitting the nodes of the computational grid. It can account for crack branching; however, the crack directions are constrained by existing mesh faces, which may lead to mesh dependence. Also, the stress in flow elements is calculated explicitly separate from the surrounding solid elements that can impose additional limits on the time step stability condition for explicit integration. The second approach uses embedded flow elements to model the cracks. Typical thickness of the cracks is much smaller than the element size. Therefore, gas pressure in the cracks is assumed to be in stress equilibrium with the element stress. To achieve this, the crack thickness and the state of the gas is updated simultaneously with the state of the solid element which contains the crack. Therefore, the time step is controlled by the explicit solver applied for the solid and does not depend on the thickness of the crack. The main disadvantage of the second approach is due to the complexity of modeling multiple intersecting cracks, which go through the same element. We discuss the areas of possible applications of these 2 methods and the ways to improve and enhance them for future practical applications.


  • A thermomechanical anisotropic continuum model for geological materials with multiple joint sets

    by O. Yu. Vorobiev, M. B. Rubin

    Summary: Joints in geological materials introduce elastic compliance and weak planes on which sliding can occur. Although these materials can have multiple joint sets, they often have preferred orientations that cause both elastic and inelastic anisotropic response even when the unjointed material is isotropic. Azimuthal variations in radial velocity and polarity of tangential motion have been observed in experimental data for wave propagation caused by an initially spherical source in a geological material with multiple joint sets. This observed tangential ground motion was found to be related to mechanical anisotropy caused by preferred orientations of joints in the rock. This paper describes thermomechanical continuum constitutive equations, which model the effects of multiple persistent joint sets. A number of quasi‐static examples are considered, which show that the proposed model predicts anisotropic effects of sliding on multiple joint sets similar to those exhibited by computationally expensive mesoscale calculations, which model joint sets explicitly.