Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Torunn Kringlen Ervik has a total of 66 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Characterization of occupational exposure to airborne particles and bioaerosols in dental clinics

    by Rubiyat E Islam, Lina Wik, Vibeke E Ansteinsson, Pål Graff, Shan Zienolddiny-Narui, Torunn K Ervik

    Occupational exposure to airborne particles and bioaerosols in dental clinics is a potential hazard to dental health workers. Current studies on airborne particles and bioaerosols in dental clinics are limited and methodologically diverse, leaving gaps in the understanding of airborne particles in real-life dental settings. The aim of the study was to investigate the size, concentration, and composition of particles produced during dental procedures, and determine the exposure levels of dental personnel to respirable particles and bioaerosols in dental clinical environments with different characteristics. The study included two conventional dentist offices and one specialty clinic. The number concentration and size distribution of particles released during different dental procedures were monitored in real-time in dental procedure rooms. Personal samplers were used in parallel to collect the respirable and inhalable particle fractions. Total bacterial and total fungal DNA concentrations were quantified in the inhalable particle fraction by droplet digital polymerase chain reaction. Particle morphology and chemical composition were analyzed using scanning electron microscopy. The highest geometric mean value of the respirable particle mass concentration (0.06 mg/m3) was below the Norwegian occupational exposure limit for respirable dust of 5 mg/m3. Real-time sampling indicated that particle number concentrations were elevated during working hours in two clinics, with peak levels observed in one clinic coinciding with air polishing activities. The results also showed significant variations in bacterial and fungal DNA concentration levels (P < 0.0001). Many collected particles originated from powders used in dental treatments. Despite low respirable particle mass concentrations, increased levels of ultrafine particles during dental procedures highlight potential health risks to dental professionals. These findings also underscore the importance of advanced ventilation and safety measures to mitigate occupational exposure in dental environments.


  • Open Access

    Characterization of dust and crystalline silica exposure during indoor demolition

    by Johanne Ø Halvorsen, Pål Graff, Elin Lovise Folven Gjengedal, Torunn K Ervik

    Exposure to dust and respirable crystalline silica (RCS) is a continuing concern in the construction industry when working with silica-containing materials, such as concrete, brick, or stone. Increased knowledge of the dust characteristics can be used to improve measures to reduce potential exposure. This study aimed to characterize dust collected from indoor demolition in terms of particle size distribution and mineral content, including quartz. Airborne dust was collected with Sioutas cascade impactors at five different construction sites involved in indoor demolition and renovation. Four of the locations had workers demolishing concrete, while at the fifth location brick structures were demolished. An aerodynamic particle sizer (APS) was used to continually monitor the particle number concentrations in the size range 0.54 µm to 17 µm. Material samples of demolished material were collected from each location to determine mineral content. The filters from the Sioutas cascade impactors were weighted to determine dust concentrations in five size fractions ranging from 10 µm down to less than 0.25 µm. Quartz concentrations were quantified with X-ray diffraction using the NIOSH 7500 method and Rietveld refinement was further used to determine other mineral content in the Sioutas impactor samples and material samples. Respirable dust and quartz concentrations were calculated from the Sioutas data. The mass- and number-based particle size distributions measured by the APS were similar for the four locations involved in concrete demolition, whereas the location working with brick had a different distribution. The concentration levels varied widely, and the highest levels were observed at an enclosed location with no natural ventilation where concrete demolition took place. Limited natural or mechanical ventilation led to an accumulation of smaller particles around 1 µm and a lower mass median aerodynamic diameter for RCS, down to 1.2 µm, compared to locations with ventilation. The quartz percentages of the dust collected by Sioutas impactors were found to increase with increasing particle size. The dust contained less quartz than the source material, and an up-concentration of softer minerals like calcite was observed. The knowledge of particle size distributions and concentration levels occurring in the field during indoor demolition is important to ensure effective measures to reduce worker exposure. The results highlight the importance of effective ventilation to reduce the accumulation of airborne particles.


  • Open Access

    Impact of air recirculation and humidification systems on wood dust exposure during woodworking

    by Anne Straumfors, Ine Pedersen, Erika Zardin Brinchmann, Torunn Kringlen Ervik, Anani Afanou, Kristine H Anmarkrud, Monica Eidhammer, Oda A H Foss, Nils Petter Skaugset

    Employees in the woodworking industry, including carpentry workshops, wood product factories, and the wooden house industry, are exposed to wood dust at work. In Norway, this industry is exempt from regulations banning air recirculation, intended to prevent harmful substance buildup in working environments. While wood dust exposure is linked to increased risks of cancer and respiratory diseases, eliminating the exemption could have significant economic consequences for companies reliant on heated air recirculation during winter. A detailed characterization of the exposure is needed to evaluate the health risks associated with recirculated air. Wood dust contains components like resin acids, endotoxins, fungi, bacteria, monoterpenes, and aldehydes, which can irritate the skin, eyes, and respiratory system. Understanding these exposures is crucial for evaluating whether existing occupational exposure limits (OELs) adequately protect workers’ health. This study aimed to assess wood dust and associated exposures in companies with and without air recirculation or humidification. Between 2019 and 2023, full-shift personal aerosol sampling was conducted in 23 companies during winter. Samples were analyzed for wood dust mass, endotoxin, bacteria and fungi, resin acid, monoterpenes, and aldehydes. Log-transformed exposure data were analyzed by mixed models using company types and work-related conditions as fixed effects. Results showed average exposure below OELs but with significant variability. About 25% of measurements exceeded the OEL for inhalable wood dust of 1 mg/m3. Air recirculation had mixed effects; it lowered the monoterpene exposure by 95% (from GM 597 µg/m3 to GM 27 µg/m3) but increased the GM microbial exposure 2 to 5 times across companies. The impact of air recirculation varied across company types. For building element production, it nearly doubled the wood dust exposure from soft woods (from GM 0.15 mg/m3 to GM 0.27 mg/m3), while for door/window manufacturers, exposure was nearly halved compared to those not using air recirculation (from GM 0.44 mg/m3 to GM 0.25 mg/m3). Air humidification lowered the inhalable dust exposure by 59% across the company (from GM 1.36 mg/m3 to 0.56 mg/m3) but led to increases in monoterpene by 90 % (from GM 86 µg/m3 to GM 792 µg/m3) and microbial exposure by up to 64%. Companies manufacturing interior products without a humidification system had resin acid exposure levels that were 10 times higher (GM 3323 ng/m3) compared to those with a humidification system (GM 344 ng/m3). The variability in exposures was mostly influenced by company-specific practices. Evaluation of preventive measures should therefore be tailored to the individual company.

  • Open Access

    European harmonization of asbestos exposure assessment: comparing PCM, SEM, and TEM to derive conversion factors

    by Remy Franken, Peter Tromp, Torunn Kringlen Ervik, James Staff, Keld Alstrup Jensen, Céline Eypert-Blaison, Anders Brostrøm, Annapaola Cannizzaro, Maria Teresa Sanchez Cabo, Maria Rosaria Bruno, et al.

    After the European ban on the use of asbestos, exposure assessment of asbestos became imperative for ensuring compliance with safety standards. However, each European country has their own legislation and requirements, including measurement strategies, analytical techniques such as the microscope used as well as occupational exposure limits (OELs). The recent EU directive (EU) 2023/2668 significantly lowered the OEL for asbestos from 100,000 fibres/m³ 8-h time-weighted average to either 2,000 fibres/m³ when counting fibres between 0.2 and 3 µm in diameter, or 10,000 fibres/m³ when counting fibres thinner than 0.2 µm and dictates a transition from optical to electron microscopy analysis by the end of 2029. This change impacts Member States that rely on phase-contrast microscopy (PCM) to quantify asbestos concentrations, prompting the need for a standardized comparison between different analytical methods. Therefore, our study investigated whether conversion factors could be developed, enabling comparison of results obtained with different analytical techniques. To achieve this, a phased approach was applied, involving a survey of measurement strategies implemented by different countries in Europe, a literature search, and analysis of in-house data to explore differences between analytical techniques. Standardized conversion factors were developed via (i) direct comparison of concentrations from analysis with scanning electron microscopy (SEM), transmission electron microscopy (TEM), and/or PCM, (ii) a multiple linear regression model, and (iii) via log probability plots from raw data on fibre dimensions. Ten institutes from the ‘Partnership for European Research in Occupational Safety and Health’ (PEROSH) asbestos network participated in this study. The results showed that SEM and PCM were the most commonly used analytical techniques, with TEM also being used in 3 countries. OELs and measurement standards/protocols varied across countries, and most employed national derived standards for measurements. Conversion factors overall showed that measurements analysed by TEM resulted in higher fibre concentrations followed by PCM and SEM. Although conversion factors were developed, these were influenced by factors such as material type, applied energy, and local controls, preventing the derivation of a general conversion method.


  • Open Access

    Application of X-ray diffraction with Rietveld refinement to quantify mineral composition including crystalline silica in respirable dust

    by Johanne Østereng Halvorsen, Peter Stacey, Pål Graff, Elin Lovise Folven Gjengedal, Torunn K. Ervik

    This study aimed to test the use of Rietveld refinement on respirable aerosol samples to determine the phase of respirable crystalline silica (RCS) and other minerals. The results from the Rietveld refinement were compared to an external standard method and gravimetrical measurements. Laboratory samples consisting of α-quartz, feldspar, and calcite with variable proportions and total mass loadings were made and analyzed using the NIOSH 7500 Silica, Crystalline, by XRD (filter redeposition) method, followed by Rietveld refinement. Field samples of respirable dust, from construction sites working with concrete, brick, and other materials were included. To correct for amorphous content and unidentified phases, an internal standard was added to the field samples, which were treated like laboratory samples. Rietveld refinement was successfully used for quantification of RCS in laboratory and field samples. The method showed comparable results to the NIOSH 7500 method for quartz and remained linear for laboratory samples up to 20 mg. The lowest quantified amounts of quartz in the laboratory samples were 5 µg. The two methods yielded similar results for RCS in field samples with a total mass of up to 15 mg and a quartz content of 1.8 wt% to 11 wt%. A total sample mass of above 0.5 mg was required for optimal quantification of crystalline phases by Rietveld refinement. The method proved useful in determining RCS and other crystalline components in field samples and corrected for interferences even with a complex matrix and high mass loading.


  • Open Access

    Measurements of dust and respirable crystalline silica during indoor demolition and renovation

    by Johanne Ø Halvorsen, Pål Graff, Elin Lovise Folven Gjengedal, Torunn K Ervik

    Increased focus on renovating and maintaining the existing building stock is an integral part of the circular economy, however this might pose challenges to workers health. The aim of this study was to assess the renovation workers’ exposure to inhalable dust, thoracic dust, respirable dust, and respirable crystalline silica (RCS). Personal aerosol samples were collected as full shift samples from 92 workers to a total of 407 samples. Fourteen locations around Oslo, Norway was visited for multiple days with repeated measurements of the same individual. Particulate matter from 3 aerosol fractions, respirable, thoracic, and inhalable, were analyzed gravimetrically, and the respirable fraction was analyzed for RCS by NIOSH 7500 method for X-ray diffraction (XRD) with low temperature plasma ashing sample preparation. The total measured concentrations of respirable dust (n = 192) had a geometric mean (GM) of 0.88 mg/m3, RCS concentrations (n = 182) had a GM of 0.040 mg/m3, thoracic dust (n = 131) had GM 2.4 mg/m3, and inhalable dust (n = 84) had a GM of 8.5 mg/m3. The maximum measured concentrations were 29 mg/m3, 3.2 mg/m3, 65 mg/m3, and 163 mg/m3, respectively. Workdays involving tasks such as mechanical demolition and clearing out demolished materials led to the highest exposure levels of both dust and RCS. However, other workers at the renovation sites were indirectly exposed to a considerable amount of RCS. This study revealed substantial exposure to both RCS and dust during renovation, and protective measures are warranted to reduce exposure levels in the industry.


  • Open Access

    Characterization of particle exposure during tunnel excavation by tunnel boring machines

    by Torunn K Ervik, Mimmi Leite, Stephan Weinbruch, Karl-Christian Nordby, Dag G Ellingsen, Bente Ulvestad, Kari Dahl, Balazs Berlinger, Nils Petter Skaugset

    Tunnel boring machines (TBMs) are used to excavate tunnels in a manner where the rock is constantly penetrated with rotating cutter heads. Fine particles of the rock minerals are thereby generated. Workers on and in the vicinity of the TBM are exposed to particulate matter (PM) consisting of bedrock minerals including α-quartz. Exposure to respirable α-quartz remains a concern because of the respiratory diseases associated with this exposure. The particle size distribution of PM and α-quartz is of special importance because of its influence on adverse health effects, monitoring and control strategies as well as accurate quantification of α-quartz concentrations. The major aim of our study was therefore to investigate the particle size distribution of airborne PM and α-quartz generated during tunnel excavation using TBMs in an area dominated by gneiss, a metamorphic type of rock. Sioutas cascade impactors were used to collect personal samples on 3 separate days. The impactor fractionates the dust in 5 size fractions, from 10 µm down to below 0.25 µm. The filters were weighted, and the α-quartz concentrations were quantified using X-ray diffraction (XRD) analysis and the NIOSH 7500 method on the 5 size fractions. Other minerals were determined using Rietveld refinement XRD analysis. The size and elemental composition of individual particles were investigated by scanning electron microscopy. The majority of PM mass was collected on the first 3 stages (aerodynamic diameter = 10 to 0.5 µm) of the Sioutas cascade impactor. No observable differences were found for the size distribution of the collected PM and α-quartz for the 3 sampling days nor the various work tasks. However, the α-quartz proportion varied for the 3 sampling days demonstrating a dependence on geology. The collected α-quartz consisted of more particles with sizes below 1 µm than the calibration material, which most likely affected the accuracy of the measured respirable α-quartz concentrations. This potential systematic error is important to keep in mind when analyzing α-quartz from occupational samples. Knowledge of the particle size distribution is also important for control measures, which should target particle sizes that efficiently capture the respirable α-quartz concentration.


  • Open Access

    Measurements of airborne asbestos fibres during refurbishing

    by Torunn Kringlen Ervik, Stine Eriksen Hammer, Nils Petter Skaugset, Pål Graff

    Although the use of asbestos fibres in building materials has been prohibited in Norway since 1985, asbestos-containing materials (ACMs) are still found in many buildings. Lack of knowledge and awareness of these materials may lead to exposure during refurbishing. The aim of this study was to investigate the airborne fibre concentration and classify fibres found during the abatement of various ACMs. The release of fibres during short-term work tasks, such as drilling and sawing, was also investigated. Parallel air samples were collected during asbestos abetment of different building materials and analysed with scanning electron microscope (SEM) and phase-contrast microscope (PCM), respectively. Material samples were analysed with SEM. A real-time fibre monitor was used to measure asbestos during short-term work. The highest fibre concentrations were measured for samples collected during the removal of asbestos insulating boards (1.5–4.5 fibres/cm3 [f/cm3]), and the numbers were relatively similar for SEM and PCM. A large difference in asbestos concentrations was found between SEM and PCM when analysing floor materials, which were probably caused by a high number of gypsum fibres that the PCM operator counted. Thin fibres (3.


  • Open Access

    Quasi-monocrystalline silicon for low-noise end mirrors in cryogenic gravitational-wave detectors

    by Frank M. Kiessling, Peter G. Murray, Maya Kinley-Hanlon, Iryna Buchovska, Torunn K. Ervik, Victoria Graham, Jim Hough, Ross Johnston, Mike Pietsch, Sheila Rowan, et al.

    Mirrors made of silicon have been proposed for use in future cryogenic gravitational-wave detectors, which will be significantly more sensitive than current room-temperature detectors. These mirrors are planned to have diameters of ≈50 cm and a mass of ≈200 kg. While single-crystalline float-zone silicon meets the requirements of low optical absorption and low mechanical loss, the production of this type of material is restricted to sizes much smaller than required. Here we present studies of silicon produced by directional solidification. This material can be grown as quasi-monocrystalline ingots in sizes larger than currently required. We present measurements of a low room-temperature and cryogenic mechanical loss comparable with float-zone silicon. While the optical absorption of our test sample is significantly higher than required, the low mechanical loss motivates research into further absorption reduction in the future. While it is unclear if material pure enough for the transmissive detector input mirrors can be achieved, an absorption level suitable for the highly reflective coated end mirrors seems realistic. Together with the potential to produce samples much larger than ≈50 cm, this material may be of great benefit for realizing silicon-based gravitational-wave detectors.