YWYekan Wang

Yekan Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yekan Wang has a total of 86 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Structural and Chemical Defect Characterization for Selectively Doped GaN

    by Yekan Wang, Kenny Huynh, Michael Liao, Mark Goorsky

  • Dissolution of Mg-enriched defects in implanted GaN and increased p-type dopant activation

    by K. Huynh, Y. Wang, M. E. Liao, J. Tweedie, P. Reddy, M. H. Breckenridge, R. Collazo, Z. Sitar, K. Sierakowski, M. Bockowski, et al.

    Annealing Mg-implanted homoepitaxial GaN at temperatures above 1400 °C eliminates the formation of inversion domains and leads to improved dopant activation efficiency. Extended defects, in the form of inversion domains, contain electrically inactive Mg after post-implantation annealing at temperatures as high as 1300 °C (one GPa N2 overpressure), which results in a low dopant activation efficiency. Triple-axis x-ray data reveal that implant-induced strain is fully relieved after annealing at 1300 °C for 10 min, indicating that strain-inducing point defects formed during implantation have reconfigured and inversion domains are formed. However, annealing at temperatures of 1400–1500 °C (one GPa N2 overpressure) eliminates the presence of the inversion domains. While residual defects, such as dislocation loops, still exist after annealing at and above 1400 °C, chemical analysis at multiple dislocation loops shows no sign of Mg segregation. Meanwhile, an overall decreasing trend in the dislocation loop density is observed after annealing at the higher temperatures and longer times. Additionally, once inversion domains are formed and the samples are cooled to room temperature, they are shown to dissolve with subsequent annealing above 1400 °C. While such defects have been observed before, the important finding that such defects can be dissolved with a short, higher temperature step is key. Earlier work [Breckenridge et al., J. Appl. Phys. Lett. 118, 022101 (2021)] addressing electrical measurements of these types of samples showed that annealing at 1400 °C leads to a dopant activation efficiency that is an order of magnitude higher than that observed at 1300 °C. This work complements earlier work by identifying the inversion domains, which incorporate Mg, and points to the benefits, in terms of defect density and p-type dopant activation, of using higher temperature (>1400 °C) annealing cycles to activate Mg in GaN, even if the Mg-containing inversion domains had been formed during lower temperature annealing.


  • Open Access

    Origins of epitaxial macro-terraces and macro-steps on GaN substrates

    by Michael E. Liao, William L. Olsen, Kenny Huynh, Dorian P. Luccioni, Yekan Wang, XianRong Huang, Michael J. Wojcik, Andrew A. Allerman, Mark S. Goorsky

    Localized lattice distortions in GaN substrates can serve as nucleation sites for epitaxial macro-steps and macro-terraces. These detrimental macro-scale features give rise to optically hazy homoepitaxial GaN surfaces. After nucleating, these macro-features grow laterally along the surface and coalesce, leading to significant coverage of the wafer surface. Dot-core GaN substrates consisting of a periodic array of cores were used as a defect-engineered system, where dislocations are intentionally concentrated at the cores. The high density of threading dislocations at the cores induced localized lattice distortions. These distortions are associated predominantly with lattice tilt on the order of hundreds of arcsec across ∼0.5 mm laterally along the wafer surface. The resulting macro-features that nucleated at these localized distorted sites were made up of macro-terraces with lengths ranging ∼30–∼150 μm and macro-step heights ranging ∼200–∼400 nm. Another source of localized distortion was threading screw dislocations or GaN nanopipes that resulted in spiral growth and hillock formation. Based on x-ray topography and optical microscopy measurements, we speculate that the coalescence of hillocks evolves into macro-terraces and macro-steps. While previous studies focused on the substrate miscut as a means to control macro-feature formation, we show that localized lattice tilt from defects is another important contributor to macro-feature formation.


  • Depth-dependent recovery of thermal conductivity after recrystallization of amorphous silicon

    by Kenny Huynh, Yekan Wang, Michael E. Liao, Thomas Pfeifer, John Tomko, Ethan Scott, Khalid Hattar, Patrick E. Hopkins, Mark S. Goorsky

    The depth-dependent recovery of silicon thermal conductivity was achieved after the recrystallization of silicon that had been partially amorphized due to ion implantation. Transmission electron microscopy revealed nanoscale amorphous pockets throughout a structurally distorted band of crystalline material. The minimum thermal conductivity of as-implanted composite material was 2.46 W m−1 K−1 and was found to be uniform through the partially amorphized region. X-ray diffraction measurements reveal 60% strain recovery of the crystalline regions after annealing at 450 °C for 30 min and almost full strain recovery and complete recrystallization after annealing at 700 °C for 30 min. In addition to strain recovery, the amorphous band thickness reduced from 240 to 180 nm after the 450 °C step with nanoscale recrystallization within the amorphous band. A novel depth-dependent thermal conductivity measurement technique correlated thermal conductivity with the structural changes, where, upon annealing, the low thermal conductivity region decreases with the distorted layer thickness reduction and the transformed material shows bulk-like thermal conductivity. Full recovery of bulk-like thermal conductivity in silicon was achieved after annealing at 700 °C for 30 min. After the 700 °C anneal, extended defects remain at the implant projected range, but not elsewhere in the layer. Previous results showed that high point-defect density led to reduced thermal conductivity, but here, we show that point defects can either reform into the lattice or evolve into extended defects, such as dislocation loops, and these very localized, low-density defects do not have a significant deleterious impact on thermal conductivity in silicon.


  • Open Access

    High figure of merit extreme bandgap Al0.87Ga0.13N-Al0.64Ga0.36N heterostructures over bulk AlN substrates

    by Kamal Hussain, Abdullah Mamun, Richard Floyd, Didarul Alam, Michael E. Liao, Kenny Huynh, Yekan Wang, Mark Goorsky, Mvs Chandrashekhar, Grigory Simin, et al.

    We report on high-quality n-Al0.87Ga0.13N-A0.64Ga0.36N heterostructures over single crystal AlN. For these pseudomorphic heterostructures, high-resolution X-ray and X-ray Topographic analysis was used to establish a threading dislocation density of 7 × 103 cm−2. Using reverse composition graded n+-Al x Ga1-x N contact layers, we obtained linear ohmic contacts with 4.3 Ω mm specific resistance. A critical breakdown field >11 MV cm−1 was also measured. In combination with the channel resistance of 2400 Ω sq−1, these translate to a Baliga’s Figure of Merit of 2.27 GW cm−2. This, to the best of our knowledge is the highest reported value for extreme bandgap AlGaN heterostructures.


  • Investigation of the Reverse Leakage Behavior and Substrate Defects in Vertical GaN Schottky and PIN Diodes

    by Yekan Wang, Michael E Liao, Kenny Huynh, William Olsen, James C Gallagher, Travis J Anderson, Xianrong Huang, Michael J Wojcik, Mark S Goorsky

    In this work, the effects of the substrate defect density and distribution on the reverse leakage behavior of GaN vertical Schottky diodes and p–i–n diodes are investigated. A direct connection between the reverse leakage behavior of GaN based vertical devices and the dislocation density of the underlying material was determined. The difference in the leakage current for devices on different locations of the wafer can be as high as 6 orders of magnitude (for p–i–n diodes) at −200V, for HVPE substrate with inhomogeneous but predictable defect distributions (GaN substrates with dot-core inversion domain features). For comparison, using HVPE substrates with uniform defect distribution (but with no cores), the p–i–n diodes show much more uniform leakage behavior, varying within only an order of magnitude, and that range fell within the much greater range of that for the inhomogeneous substrates. The substrates with inhomogeneous defect distribution proved to be useful to show the direct correlation. The topography measurements confirmed that the wafers with inhomogeneous defect distribution possess periodically patterned core-centers with higher defect density and larger lattice distortions surrounded by other regions, which have very low defect concentrations. Devices located away from the defective core-centers result in a reduction of the reverse bias leakage by over two orders of magnitude at −10 V for Schottky diodes. Similar trends are also observed in the p–i–n diodes; the devices close to the core centers show the highest reverse leakage (>0.01 A cm −2 at −200V). Devices further away from the core-centers (lower dislocation density) show lower reverse leakage current. Moreover, the p–i–n diodes on regions more than 300 μ m away from the core-centers show the best leakage behavior (−7 A cm −2 at −200V) of all the devices, outperforming the devices on the substrates with uniform defect distribution (∼10 −6 A cm −2 at −200V). The results from this study show that the substrate defect density and distribution play important roles in the device leakage current. X-ray topography is extremely effective for studying defect characteristics underneath individual devices. The use of the wafers with inhomogeneous, but predictable defect density clearly demonstrated the importance of low defect densities for high device performance.


  • Structural Characterization of Dot-Core GaN Substrates with Annealing Under Growth-Like Conditions Using Synchrotron Monochromatic X-ray Topography

    by Y. Wang, M. E. Liao, K. Huynh, A. A. Allerman, M. S. Goorsky

    In this work, synchrotron monochromatic X-ray topography was employed to study the structural characteristics of as-received c-plane dot-core GaN substrates and then to investigate the structural evolution with annealing under growth-like conditions at 1050 °C for 10 h. Single exposure X-ray topography images were obtained using the (11 2 4) GaN asymmetric reflection. These images were superimposed to quantify the lattice distortions in regions near the dot-cores and in the regions between these defects. The results show that different dot-core substrates from the same vendor exhibit different defect distribution, lattice distortions around the cores, and different radii of lattice curvature, ranging from 7 m to 25 m. Annealing under growth-like conditions reduces both the global and local lattice distortions. Globally, the radius of curvature across the wafer increased from 17 m to 27 m after annealing. The local radius of curvature across the highly distorted core regions also increased from 0.47 ± 0.04 m to 0.9 ± 0.2 m after annealing. An increase in the radius of curvature is an indication of stress reduction. The lattice tilt around the cores varies from 0.01°−0.02°. The lattice planes around the centers of cores are highly distorted, and the magnitude of the tilt generally decreases radially away from the core center. After annealing, these local distortions decreased as well. A general core model was built based on these experimental results, providing a fundamental structural picture of dot-core regions, which has been lacking in the current literature.


  • Strain Recovery and Defect Characterization in Mg‐Implanted Homoepitaxial GaN on High‐Quality GaN Substrates

    by Yekan Wang, Kenny Huynh, Michael E. Liao, Hsuan-Ming Yu, Tingyu Bai, James Tweedie, Mathew Hayden Breckenridge, Ramon Collazo, Zlatko Sitar, Michal Bockowski, et al.

    The evolution of defects due to high‐pressure annealing of magnesium ion‐implanted epitaxial GaN grown on high‐quality GaN substrates is investigated. Changes in the implant‐induced strain are quantified as a function of annealing temperature and time. After annealing at 1300 °C for 10 min, the implant‐induced strain is fully relieved and accompanied by the presence of extended defects such as basal plane stacking faults and prismatic loops. Approximately one‐third of the original implant‐induced strain remains after annealing at 700 °C, and 5% of the original strain remains at 1000 °C for 100 min. In all cases, nearly all of the recovered strain occurs within first few minutes of annealing. A prominent increase in the asymmetric (104) triple axis X‐ray rocking curve full width at 0.01 maximum (FW0.01M) is observed after annealing at 1300 °C for 10 min. After annealing at 1300 °C for 100 min, a subsequent decrease in FW0.01M is correlated with a reduction of the extended defect density from 4 × 108 to 3 × 107 cm−2, determined through transmission electron microscope (TEM) measurements. Further reduction in the density of the extended defects by optimizing annealing temperature and time is expected to improve the performance of GaN‐based vertical power devices.


  • Diamond Seed Size and the Impact on Chemical Vapor Deposition Diamond Thin Film Properties

    by T. Bai, Y. Wang, T. I. Feygelson, M. J. Tadjer, K. D. Hobart, N. J. Hines, L. Yates, S. Graham, J. Anaya, M. Kuball, et al.

    Diamond seeds were assessed for their role in the heterogeneous nucleation for diamond films deposited on silicon using chemical vapor deposition. Two diamond seed sizes—4 nm and 20 nm—were studied. The study revealed that the larger seed size, even when with a smaller seed density, produces a larger grain size near the interface region, and led to a higher in-plane thermal conductivity as measured by Raman thermography. By fine control of the seed size and density, thermal conductivity near the nucleation region can therefore be improved. This demonstrates that the seeding condition is critical to diamond film growth for thermal applications in electronic devices.


  • Exfoliation of β-Ga2O3Along a Non-Cleavage Plane Using Helium Ion Implantation

    by Michael E. Liao, Yekan Wang, Tingyu Bai, Mark S. Goorsky

    An important step in the successful transfer of controlled thickness, wafer-scale β-Ga2O3 layers is demonstrated through exfoliation via helium ion implantation. He+ ions were implanted into epi-ready (010) β-Ga2O3 substrates at room temperature with an ion energy of 160 keV and a dose of 5 × 1016 cm−2. The implanted substrate was then annealed at 200°C followed by 500°C. The lower temperature step initiated He bubble nucleation while the higher temperature step promoted He bubble growth at the projected range beneath the substrate surface. No surface blistering was observed after the 200°C anneal. After the 500°C anneal step, micron-sized surface blistering covering the entire implanted area was observed, confirming exfoliation of β-Ga2O3 along a non-cleavage plane. Triple-axis X-ray diffraction ω:2θ measurements showed that after annealing at 500°C, the implantation-induced strain was removed. The ω scans showed some peak broadening after the low temperature step and more extensive broadening after the high temperature step; this observation corresponds to an increase in lattice plane tilt due to the formation of He bubbles at the projected range. Prior to annealing, scanning transmission electron microscopy images showed a dark contrast at the projected range due to the implantation of a high concentration of He ions. After the 500°C anneal, large cracks at the projected range were observed. These observations match early reports of silicon blistering which, when combined with established direct wafer bonding practices, is expected to lead to large-scale transfer of controlled thickness β-Ga2O3 layers along non-cleavage-plane orientations.