Muhammad Razlan Zakaria
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Muhammad Razlan Zakaria has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Fatima Javed
Department of Chemistry, Shaheed Benazir Bhutto Women University, Peshawar 25000, Pakistan
1 shared publication - Haslan Fadli Ahmad Marzuki
SIRIM Kulim, Kulim Hi-Tech Park, Kulim 09000, Kedah, Malaysia
1 shared publication - Hazizan Md Akil
School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia (USM), Nibong Tebal, Malaysia
1 shared publication - Mohd Hafiz Zamri
School of Materials and Mineral Resources Engineering, Engineering Campus, University Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang, Malaysia
1 shared publication - Muhammad Helmi Abdul Kudus
School of Mechanical Engineering, Engineering Campus, Universiti Sains Malaysia, Nibong Tebal 14300, Pulau Pinang, Malaysia
1 shared publication - Muhammad Ibrar
Department of Physics, Islamia College Peshawar, Peshawar 25000, Pakistan
1 shared publication
Latest Publications
- Open Access
Structure Property Investigation of Glass-Carbon Prepreg Waste-Polymer Hybrid Composites Degradation in Water Condition
The limited shelf life of carbon prepreg waste (CPW) from component manufacturing restricts its use as a composite reinforcement fibre on its own. However, CPW can be recycled with glass fibre (GF) reinforcement to develop a unique remediate material. Therefore, this study fabricated (1) a glass fibre-carbon prepreg waste reinforced polymer hybrid composite (GF-CPW-PP), (2) a polypropylene composite (PP), (3) a carbon prepreg waste reinforced composite (CPW-PP), and (4) a glass fibre reinforced composite (GF-PP) and reported their degradation and residual tension properties after immersion in water. The polymer hybrid composites were fabricated via extrusion technique with minimum reinforce glass-carbon prepreg waste content of 10 wt%. The immersion test was conducted at room temperature using distilled water. Moisture content and diffusion coefficient (DC) were determined based on water adsorption values recorded at 24-h intervals over a one-week period. The results indicated that GF-PP reinforced composites retained the most moisture post-168 h of immersion. However, hardness and tensile strength were found to decrease with increased water adsorption. Tensile strength was found to be compromised since pores produced during hydrolysis reduced interfacial bonding between glass fibre and prepreg carbon reinforcements and the PP matrix.
Open AccessStructure Property Investigation of Glass-Carbon Prepreg Waste-Polymer Hybrid Composites Degradation in Water Condition
The limited shelf life of carbon prepreg waste (CPW) from component manufacturing restricts its use as a composite reinforcement fibre on its own. However, CPW can be recycled with glass fibre (GF) reinforcement to develop a unique remediate material. Therefore, this study fabricated (1) a glass fibre-carbon prepreg waste reinforced polymer hybrid composite (GF-CPW-PP), (2) a polypropylene composite (PP), (3) a carbon prepreg waste reinforced composite (CPW-PP), and (4) a glass fibre reinforced composite (GF-PP) and reported their degradation and residual tension properties after immersion in water. The polymer hybrid composites were fabricated via extrusion technique with minimum reinforce glass-carbon prepreg waste content of 10 wt%. The immersion test was conducted at room temperature using distilled water. Moisture content and diffusion coefficient (DC) were determined based on water adsorption values recorded at 24-h intervals over a one-week period. The results indicated that GF-PP reinforced composites retained the most moisture post-168 h of immersion. However, hardness and tensile strength were found to decrease with increased water adsorption. Tensile strength was found to be compromised since pores produced during hydrolysis reduced interfacial bonding between glass fibre and prepreg carbon reinforcements and the PP matrix.
- Open Access
Improvement of Fracture Toughness in Epoxy Nanocomposites through Chemical Hybridization of Carbon Nanotubes and Alumina
The current study investigated the effect of adding a carbon nanotube–alumina (CNT–Al2O3) hybrid on the fracture toughness of epoxy nanocomposites. The CNT–Al2O3 hybrid was synthesised by growing CNTs on Al2O3 particles via the chemical vapour deposition method. The CNTs were strongly attached onto the Al2O3 particles, which served to transport and disperse the CNTs homogenously, and to prevent agglomeration in the CNTs. The experimental results demonstrated that the CNT–Al2O3 hybrid-filled epoxy nanocomposites showed improvement in terms of the fracture toughness, as indicated by an increase of up to 26% in the critical stress intensity factor, K1C, compared to neat epoxy.
Open AccessImprovement of Fracture Toughness in Epoxy Nanocomposites through Chemical Hybridization of Carbon Nanotubes and Alumina
The current study investigated the effect of adding a carbon nanotube–alumina (CNT–Al2O3) hybrid on the fracture toughness of epoxy nanocomposites. The CNT–Al2O3 hybrid was synthesised by growing CNTs on Al2O3 particles via the chemical vapour deposition method. The CNTs were strongly attached onto the Al2O3 particles, which served to transport and disperse the CNTs homogenously, and to prevent agglomeration in the CNTs. The experimental results demonstrated that the CNT–Al2O3 hybrid-filled epoxy nanocomposites showed improvement in terms of the fracture toughness, as indicated by an increase of up to 26% in the critical stress intensity factor, K1C, compared to neat epoxy.