Kuang-Jau Fann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kuang-Jau Fann has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
B H Peng
Department of Mechanical Engineering, National Chung Hsing University, 250, Kuokuang Road, Taichung 40227, Taiwan
1 shared publicationC H Chang
Department of Mechanical Engineering, National Chung Hsing University, 250, Kuokuang Road, Taichung 40227, Taiwan
1 shared publication- Chang-Yu Tsai
Syntec Technology Co. Ltd. , No. 25, Yanfa 2nd Road, Hsinchu Science Park
1 shared publication Chen-Yi Lee
National Chung Hsing University Department of Mechanical Engineering 145 Xingda Road, South District
1 shared publication- Chun-Chi Chen
Department of Mechanical Engineering, National Chung Hsing University, Taichung 40227, Taiwan
1 shared publication Chun-Yen Yang
National Chung Hsing University Department of Mechanical Engineering 145 Xingda Road, South District
1 shared publication
Latest Publications
- 21 February 2025
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 147 (6) , 1-18
An Artificial Intelligence Application for In-Process Springback Control of Sheet Metal Bending
Bending is the fastest and most efficient process commonly used in the industry for processing thin metal sheets into three-dimensional shapes by localized deformation using only a single geometrical die. However, suppliers provide metal sheets with variations in dimension and mechanical properties, which causes inconsistencies in the final angle after bending. This requires manual checking and correction of each angle, resulting in inefficiency. The problem can be resolved by considering the variations in the sheets and adjusting the bending stroke accordingly. This study used neural network technology to create a model that predicts the final stroke required based on load measurements during the bending process. The model was implemented and validated using a laboratory press. With a root-mean-square error of less than 0.27 deg, the model demonstrates its feasibility for practical industrial applications within the range of its training data.
- 21 February 2025
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 147 (6) , 1-18
An Artificial Intelligence Application for In-Process Springback Control of Sheet Metal Bending
Bending is the fastest and most efficient process commonly used in the industry for processing thin metal sheets into three-dimensional shapes by localized deformation using only a single geometrical die. However, suppliers provide metal sheets with variations in dimension and mechanical properties, which causes inconsistencies in the final angle after bending. This requires manual checking and correction of each angle, resulting in inefficiency. The problem can be resolved by considering the variations in the sheets and adjusting the bending stroke accordingly. This study used neural network technology to create a model that predicts the final stroke required based on load measurements during the bending process. The model was implemented and validated using a laboratory press. With a root-mean-square error of less than 0.27 deg, the model demonstrates its feasibility for practical industrial applications within the range of its training data.
- 20 August 2023
- Published by Springer Nature
- p. 274-284
On Forming Sheet Metal Parts in Single Curvature with English Wheel
- 20 August 2023
- Published by Springer Nature
- p. 274-284
On Forming Sheet Metal Parts in Single Curvature with English Wheel
- Open Access
- 1 September 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2020 (1) , 012033
Finite element study on spinning process of an aluminium tube
This article aims to have a glimpse into the effect of the spinning tool parameters (focusing on its diameter, attack angle, nose radius, and feed) by applying the explicit code of the commercial finite element analysis software LS-DYNA. The preliminary results show that the greater the axial feed, the greater the loads generated in the axial, the tangential, and the radial directions. At the same time, the larger the axial feed, the more the elements are parallel to the axial direction from the inflection point to the tube opening. Furthermore, using a larger axial feed will also cause the flaring of the tube opening and make the flaring more obvious. In addition, using a larger axial feed will not only cause a greater material accumulation in front of the attack angle, but also a larger material accumulation at the tangential rear of the nose radius. Moreover, the greater the attack angle, the greater the axial load. There is no further significant effect of the corner radius of the spinning tool on the spinning load.
- 1 September 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2020 (1) , 012033
Open AccessFinite element study on spinning process of an aluminium tube
This article aims to have a glimpse into the effect of the spinning tool parameters (focusing on its diameter, attack angle, nose radius, and feed) by applying the explicit code of the commercial finite element analysis software LS-DYNA. The preliminary results show that the greater the axial feed, the greater the loads generated in the axial, the tangential, and the radial directions. At the same time, the larger the axial feed, the more the elements are parallel to the axial direction from the inflection point to the tube opening. Furthermore, using a larger axial feed will also cause the flaring of the tube opening and make the flaring more obvious. In addition, using a larger axial feed will not only cause a greater material accumulation in front of the attack angle, but also a larger material accumulation at the tangential rear of the nose radius. Moreover, the greater the attack angle, the greater the axial load. There is no further significant effect of the corner radius of the spinning tool on the spinning load.
- Open Access
- 1 September 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2020 (1) , 012002
Study on shape memory effect of hot deep-drawn NI-TI shape memory alloy sheet part
This study investigates the properties of Ni-rich Ni-Ti shape memory alloy sheet parts during and after deep drawing process at an elevated temperature, which is under a plane tensile-compressive stress state. According to the results, the sheet metal shows superelasticity and ductility at 500°C, 550°C, and 600°C. In the hot deep drawing process, the working parameters affect the result. The higher the forming temperature and the longer the holding time at the bottom dead center of the punch or the longer the ageing shape memory treatment, the greater the height of the drawn part and the lesser the springback. The results of the subsequent free recovery experiment show that the deep drawn sheet part without ageing treatment still possesses the shape memory effect. It also shows in the further constraint recovery experiment that in a wide temperature span the deep drawn sheet part possesses a different recovery load when reacting to the phase transformation of the shape memory alloy. Furthermore, the higher the forming temperature and the shorter the ageing treatment, the greater the part recovery load.
- 1 September 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2020 (1) , 012002
Open AccessStudy on shape memory effect of hot deep-drawn NI-TI shape memory alloy sheet part
This study investigates the properties of Ni-rich Ni-Ti shape memory alloy sheet parts during and after deep drawing process at an elevated temperature, which is under a plane tensile-compressive stress state. According to the results, the sheet metal shows superelasticity and ductility at 500°C, 550°C, and 600°C. In the hot deep drawing process, the working parameters affect the result. The higher the forming temperature and the longer the holding time at the bottom dead center of the punch or the longer the ageing shape memory treatment, the greater the height of the drawn part and the lesser the springback. The results of the subsequent free recovery experiment show that the deep drawn sheet part without ageing treatment still possesses the shape memory effect. It also shows in the further constraint recovery experiment that in a wide temperature span the deep drawn sheet part possesses a different recovery load when reacting to the phase transformation of the shape memory alloy. Furthermore, the higher the forming temperature and the shorter the ageing treatment, the greater the part recovery load.
- Open Access
- 1 September 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2020 (1) , 012025
Study on pre-acceleration characteristics of servo motor applied on stamping die cushion
In this study, a servo motor controller having only the mutually exclusive switching function between velocity and force control is used to set up a servo mechanical die cushion to explore the technology of force control that can enable the cushion to obtain the pre-acceleration function. Under different torque settings of the servo motor, the final velocity and the travel stroke of the die cushion for a certain time duration have been investigated for each response surface. A design scheme to determine the setting parameters for the pre-acceleration of the die cushion, such as the torque and the time duration, in which its both response surfaces of the velocity and the stroke are used, is thus proposed and verified by examples. The results show that the design scheme is indeed feasible and would be available for corresponding technicians’ reference.
- 1 September 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2020 (1) , 012025
Open AccessStudy on pre-acceleration characteristics of servo motor applied on stamping die cushion
In this study, a servo motor controller having only the mutually exclusive switching function between velocity and force control is used to set up a servo mechanical die cushion to explore the technology of force control that can enable the cushion to obtain the pre-acceleration function. Under different torque settings of the servo motor, the final velocity and the travel stroke of the die cushion for a certain time duration have been investigated for each response surface. A design scheme to determine the setting parameters for the pre-acceleration of the die cushion, such as the torque and the time duration, in which its both response surfaces of the velocity and the stroke are used, is thus proposed and verified by examples. The results show that the design scheme is indeed feasible and would be available for corresponding technicians’ reference.
- 11 July 2021
- Published by Springer Nature
- p. 2619-2629
Localized Contact Pressure of Blankholder for Stamping Irregular Sheet Parts by Configuring the Height of the Supporting Elements
- 11 July 2021
- Published by Springer Nature
- p. 2619-2629
Localized Contact Pressure of Blankholder for Stamping Irregular Sheet Parts by Configuring the Height of the Supporting Elements
- Open Access
- 1 November 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 967 (1) , 012002
Finite Element Study on Pattern of Pins Supporting an Elastic Blankholder Used for Stamping Irregular Shaped Sheet Metal Parts
Working with individual in-process controllable elements to support an elastic blankholder is the state-of-the-art for stamping irregular shaped sheet metal parts without wrinkles and cracks. It is thus needed to carefully determine the position for each expensive device. This study is therefore aimed to appraise a feasible approach with finite element analysis, in that the blankholder is first modelled as a rigid object instead of an elastic one to evaluate the contact pressure of the blankholder to the blank during the forming process. The sites showing a locally relative high contact pressure, which are usually induced by local thickening of material, can be regarded as the locations of the supporting elements to intently form a local high pressure to control the material flow and thus to eliminate the local thickening there. As a result, since the blankholder force can be efficiently delivered from the supporting elements directly to the blankholder as well as to the blank, it is not only applied to the rectangular box-shaped part but also to a fender-like irregular sheet metal part. Furthermore, the initiated contact pressure can be maintained at locations during the whole stamping process. This is also experimentally validated by stamping a sound fender-like irregular sheet metal part with an elastic blankholder supported by elements located accordingly at those sites suggested by this study.
- 1 November 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 967 (1) , 012002
Open AccessFinite Element Study on Pattern of Pins Supporting an Elastic Blankholder Used for Stamping Irregular Shaped Sheet Metal Parts
Working with individual in-process controllable elements to support an elastic blankholder is the state-of-the-art for stamping irregular shaped sheet metal parts without wrinkles and cracks. It is thus needed to carefully determine the position for each expensive device. This study is therefore aimed to appraise a feasible approach with finite element analysis, in that the blankholder is first modelled as a rigid object instead of an elastic one to evaluate the contact pressure of the blankholder to the blank during the forming process. The sites showing a locally relative high contact pressure, which are usually induced by local thickening of material, can be regarded as the locations of the supporting elements to intently form a local high pressure to control the material flow and thus to eliminate the local thickening there. As a result, since the blankholder force can be efficiently delivered from the supporting elements directly to the blankholder as well as to the blank, it is not only applied to the rectangular box-shaped part but also to a fender-like irregular sheet metal part. Furthermore, the initiated contact pressure can be maintained at locations during the whole stamping process. This is also experimentally validated by stamping a sound fender-like irregular sheet metal part with an elastic blankholder supported by elements located accordingly at those sites suggested by this study.
- Open Access
- 8 April 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (4) , 372
Grain Size in Aluminum Alloy 6061 under Hot Ring Compression Test and after T6 Temper
Peripheral coarse grain during and after hot forming is often a major inconvenience for manufacturing aluminum alloy parts. Not only is the strength reduced, but the subsequent surface treatments are also hard to realize. The literature has shown that peripheral coarse grain is very likely induced by the previous process, such as extrusion. To investigate if peripheral coarse grain could be caused solely by hot forming, this study removed the billet surface layers. This eliminates the effect from the previous processes preparing the billets and forms ring specimens for executing ring compression test. The ring compression test can reveal the friction circumstance of the specimen to the die surface and create versatile deformation in the specimens to simulate forging situations, thereby providing multifaceted conditions to develop diverse grain size in specimen, particularly on its surface. The experiments were designed and analyzed under the Taguchi method, with consideration for factors such as working temperature, speed and amount of compression, and lubricant. Under each experiment, no peripheral coarse grains were found in the specimen, which were peeled and compressed, and even the average grain size after compression test is larger than that of the received billet. No peripheral coarse grains were found in the subsequent T6 temper either, which could, however, refine the grains.
- 8 April 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (4) , 372
Open AccessGrain Size in Aluminum Alloy 6061 under Hot Ring Compression Test and after T6 Temper
Peripheral coarse grain during and after hot forming is often a major inconvenience for manufacturing aluminum alloy parts. Not only is the strength reduced, but the subsequent surface treatments are also hard to realize. The literature has shown that peripheral coarse grain is very likely induced by the previous process, such as extrusion. To investigate if peripheral coarse grain could be caused solely by hot forming, this study removed the billet surface layers. This eliminates the effect from the previous processes preparing the billets and forms ring specimens for executing ring compression test. The ring compression test can reveal the friction circumstance of the specimen to the die surface and create versatile deformation in the specimens to simulate forging situations, thereby providing multifaceted conditions to develop diverse grain size in specimen, particularly on its surface. The experiments were designed and analyzed under the Taguchi method, with consideration for factors such as working temperature, speed and amount of compression, and lubricant. Under each experiment, no peripheral coarse grains were found in the specimen, which were peeled and compressed, and even the average grain size after compression test is larger than that of the received billet. No peripheral coarse grains were found in the subsequent T6 temper either, which could, however, refine the grains.