Emmanuelle Daran
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Emmanuelle Daran has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Benjamin Reig
Laboratoire d’Analyse et d’Architecture des Systemes-Centre National de la Recherche Scientifique (LAAS-CNRS), 7 Avenue du Colonel Roche, 31400 Toulouse, France
2 shared publications - Thierry Camps
CNRS, LAAS-MICA, 7 Avenue du Colonel Roche, 31400 Toulouse, France
2 shared publications - Veronique Bardinal
Université de Toulouse, LAAS-CNRS, CNRS, Toulouse, France
2 shared publications - Benjamin Boisnard
CNRS, LAAS, Univ de Toulouse, 7 avenue du colonel Roche, F-31400 Toulouse, France
1 shared publication D.P. Shepherd
ORC, University of Southampton, Highfield, Southampton SO17 1BJ, U.K.
1 shared publicationJean-Baptiste Doucet
CNRS, LAAS, Univ de Toulouse, 7 avenue du colonel Roche, F-31400 Toulouse, France
1 shared publication
Latest Publications
- Open Access
- 16 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 551
Uniform Fabrication of Moems Arrays Using Dry Thick Resist Films
This study aims at focusing a laser beam at the center of a microfluidic channel for optical bio-sensing applications thanks to the collective integration of tunable microlens arrays on VCSELs devices. High aspect-ratio polymer-based MOEMS are successfully fabricated on small-sized samples using thick dry photoresist films. Such dry films are easier to use and less expensive than standard thick SU-8 and can be efficiently stacked on fragile GaAs samples using a soft-thermal-printing technique. By combining double UV exposure and planar metallization, uniform fabrication of MOEMS arrays is enabled and fabricated devices exhibit reproducible electro-thermal behavior.
- 16 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 551
Open AccessUniform Fabrication of Moems Arrays Using Dry Thick Resist Films
This study aims at focusing a laser beam at the center of a microfluidic channel for optical bio-sensing applications thanks to the collective integration of tunable microlens arrays on VCSELs devices. High aspect-ratio polymer-based MOEMS are successfully fabricated on small-sized samples using thick dry photoresist films. Such dry films are easier to use and less expensive than standard thick SU-8 and can be efficiently stacked on fragile GaAs samples using a soft-thermal-printing technique. By combining double UV exposure and planar metallization, uniform fabrication of MOEMS arrays is enabled and fabricated devices exhibit reproducible electro-thermal behavior.
- 12 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 21 (4) , 41-48
Advances in Polymer-Based Optical MEMS Fabrication for VCSEL Beam Shaping
In this paper, we discuss the design, fabrication, and characterization of electrothermally actuated polymer-based microoptical electromechanical microsystems (MOEMS) for active microoptics in vertical cavity surface emitting laser (VCSEL) devices. We describe in particular the principle of a SU8-based MOEMS designed for single-mode VCSEL beam active focusing. The ultimate objective is the realization of parallel compact optical scanners for sensing applications using collective and low-cost technologies. After discussing the advantages of the epoxy resist SU-8 for fabricating an integrated movable lens on active optical devices, we present our latest advances in technology for ensuring precise MOEMS fabrication on small III-V samples and for achieving accurate alignment of lenses on suspended circular membranes. Finally, we present our first results on the beam focusing of multimode VCSELs, which demonstrate the feasibility of our approach and could provide new insights in the MEMS-VCSEL field.
- 12 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 21 (4) , 41-48
Advances in Polymer-Based Optical MEMS Fabrication for VCSEL Beam Shaping
In this paper, we discuss the design, fabrication, and characterization of electrothermally actuated polymer-based microoptical electromechanical microsystems (MOEMS) for active microoptics in vertical cavity surface emitting laser (VCSEL) devices. We describe in particular the principle of a SU8-based MOEMS designed for single-mode VCSEL beam active focusing. The ultimate objective is the realization of parallel compact optical scanners for sensing applications using collective and low-cost technologies. After discussing the advantages of the epoxy resist SU-8 for fabricating an integrated movable lens on active optical devices, we present our latest advances in technology for ensuring precise MOEMS fabrication on small III-V samples and for achieving accurate alignment of lenses on suspended circular membranes. Finally, we present our first results on the beam focusing of multimode VCSELs, which demonstrate the feasibility of our approach and could provide new insights in the MEMS-VCSEL field.
- 1 January 1998
- Published by Optica Publishing Group
- p. CThF7
2.8μm emission of Er-doped CaF2 planar waveguides fabricated by molecular beam epitaxy
The wavelength range near 3μm has many applications in medical processes due to an overlap with the absorption spectrum of water. Emission of the Er3+ ion near 2.8μm, which operates on the transition from 4I11/2 to 4I13/2 is especially promising as it can be pumped by either 800nm GaAlAs or 980nm InGaAlAs diodes, paving the way for a compact device with low electrical energy consumption.
- 1 January 1998
- Published by Optica Publishing Group
- p. CThF7
2.8μm emission of Er-doped CaF2 planar waveguides fabricated by molecular beam epitaxy
The wavelength range near 3μm has many applications in medical processes due to an overlap with the absorption spectrum of water. Emission of the Er3+ ion near 2.8μm, which operates on the transition from 4I11/2 to 4I13/2 is especially promising as it can be pumped by either 800nm GaAlAs or 980nm InGaAlAs diodes, paving the way for a compact device with low electrical energy consumption.