Komal Bapna
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Komal Bapna has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Ankit Kumar
Temperature and Humidity Metrology, CSIR-National Physical Laboratory, Dr K. S. Krishnan Marg, New Delhi, 110012, India
4 shared publicationsParvesh Kumari
Temperature and Humidity Metrology, CSIR-National Physical Laboratory, Dr K. S. Krishnan Marg, New Delhi, 110012, India
4 shared publicationsGaurav Gupta
3 shared publicationsAditya Yadav
Sensor Devices and Metrology, CSIR-National Physical Laboratory, Dr K. S. Krishnan Marg, New Delhi 110012, India
2 shared publications- Dilip Dhondiram Shivagan
CSIR-National Physical Laboratory
2 shared publications Samuel J. Ippolito
Centre for Advanced Materials & Industrial Chemistry, School of Engineering, RMIT University, Melbourne, VIC, 3000, Australia
2 shared publications
Latest Publications
- 1 November 2025
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 14 (11) , 117002
InSb Thin Film as an NIR Photodetector and Self-Powered Non-Contact Infrared Temperature Sensor
This study demonstrates an InSb based detector, uniquely capable of dual functionality operating both as an infrared photodetector and as a temperature sensor within a single device architecture. The InSb/Si 3 N 4 /Si based device architecture exhibits a dual functionality as a near-infrared (NIR) photodetector and a self-powered, non-contact infrared temperature sensor. The photodetection performance was evaluated under 1064 nm NIR LASER illumination, yielding rapid response and recovery times of 39 ms and 41 ms, respectively. At a low operating bias of 2 V, the device demonstrated a high detectivity of 2.05 × 10 8 Jones and a responsivity of 0.23 mA W −1 . The same architecture, with planar Ag contacts, exhibited strong infrared thermal sensitivity when exposed to standard blackbody radiation at temperatures ranging from 800 °C to 1200 °C, with distinct on–off switching characteristics. Notably, temperature sensing was achieved in a self-powered mode at room temperature, attributed to the formation of a built-in depletion region at the metal–semiconductor (Ag–InSb) interface. These results underscore the potential of sputter deposited InSb thin films for integrated, low-power optoelectronic applications. The dual operational capability enhances the versatility for practical applications and distinguishes it from conventional InSb detectors designed for only one mode of operation.
- 1 November 2025
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 14 (11) , 117002
InSb Thin Film as an NIR Photodetector and Self-Powered Non-Contact Infrared Temperature Sensor
This study demonstrates an InSb based detector, uniquely capable of dual functionality operating both as an infrared photodetector and as a temperature sensor within a single device architecture. The InSb/Si 3 N 4 /Si based device architecture exhibits a dual functionality as a near-infrared (NIR) photodetector and a self-powered, non-contact infrared temperature sensor. The photodetection performance was evaluated under 1064 nm NIR LASER illumination, yielding rapid response and recovery times of 39 ms and 41 ms, respectively. At a low operating bias of 2 V, the device demonstrated a high detectivity of 2.05 × 10 8 Jones and a responsivity of 0.23 mA W −1 . The same architecture, with planar Ag contacts, exhibited strong infrared thermal sensitivity when exposed to standard blackbody radiation at temperatures ranging from 800 °C to 1200 °C, with distinct on–off switching characteristics. Notably, temperature sensing was achieved in a self-powered mode at room temperature, attributed to the formation of a built-in depletion region at the metal–semiconductor (Ag–InSb) interface. These results underscore the potential of sputter deposited InSb thin films for integrated, low-power optoelectronic applications. The dual operational capability enhances the versatility for practical applications and distinguishes it from conventional InSb detectors designed for only one mode of operation.
- 27 January 2025
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 27 (6) , 3420-3429
High performance humidity sensor based on a graphene oxide–chitosan composite
An high performance humidity sensor is poposed based on composite of chitosan (CS) and graphene oxide (GO), prepared by simple drop casting method.
- 27 January 2025
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 27 (6) , 3420-3429
High performance humidity sensor based on a graphene oxide–chitosan composite
An high performance humidity sensor is poposed based on composite of chitosan (CS) and graphene oxide (GO), prepared by simple drop casting method.
- 11 July 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (31) , 21186-21196
A high-performance flexible humidity sensor based on a TiO2–MWCNT nanocomposite for human healthcare applications
Present study reveals TiO2–MWCNT nanocomposite-based flexible humidity sensor, with improved humidity sensing characteristics. It is shown that the sensor has capability to detect different breath patterns, apnea-like situations, and skin moisture in a non-invasive manner.
- 11 July 2024
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 26 (31) , 21186-21196
A high-performance flexible humidity sensor based on a TiO2–MWCNT nanocomposite for human healthcare applications
Present study reveals TiO2–MWCNT nanocomposite-based flexible humidity sensor, with improved humidity sensing characteristics. It is shown that the sensor has capability to detect different breath patterns, apnea-like situations, and skin moisture in a non-invasive manner.
- Open Access
- 13 October 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (42) , 39511-39522
Chitosan-Based Highly Sensitive Viable Humidity Sensor for Human Health Monitoring
We report a sustainable resistive-type humidity sensor based on chitosan (CS) film deposited on an interdigitated Ti/Au electrode coated SiO2 substrate using a simple drop cast approach for human health monitoring. The sensor revealed remarkably high sensitivity (5.8 MΩ/%RH), fast response/recovery time (21 s/25 s), low hysteresis (∼9.3%), excellent reversibility, wide detecting range (11-95% RH), and high selectivity toward water vapor. The calculated associated uncertainty at different %RH indicates the excellent repeatability and stable performance of the sensor. The developed sensor is tested for different human breath patterns, and it is found that the sensor can clearly distinguish between the variations in rate and depth of respiration patterns during normal, fast, deep, and nasal breathing and can monitor for apnea-like situations. The sensor is also utilized to perform noncontact skin humidity sensing. Overall, the developed CS film humidity sensor provides a viable approach for the detection of respiratory disorders and human health issues, detected by skin moisture, in a noninvasive manner.
- 13 October 2023
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 8 (42) , 39511-39522
Open AccessChitosan-Based Highly Sensitive Viable Humidity Sensor for Human Health Monitoring
We report a sustainable resistive-type humidity sensor based on chitosan (CS) film deposited on an interdigitated Ti/Au electrode coated SiO2 substrate using a simple drop cast approach for human health monitoring. The sensor revealed remarkably high sensitivity (5.8 MΩ/%RH), fast response/recovery time (21 s/25 s), low hysteresis (∼9.3%), excellent reversibility, wide detecting range (11-95% RH), and high selectivity toward water vapor. The calculated associated uncertainty at different %RH indicates the excellent repeatability and stable performance of the sensor. The developed sensor is tested for different human breath patterns, and it is found that the sensor can clearly distinguish between the variations in rate and depth of respiration patterns during normal, fast, deep, and nasal breathing and can monitor for apnea-like situations. The sensor is also utilized to perform noncontact skin humidity sensing. Overall, the developed CS film humidity sensor provides a viable approach for the detection of respiratory disorders and human health issues, detected by skin moisture, in a noninvasive manner.
- 10 November 2020
- Published by Springer Nature
- p. 307-376
Physico-Mechanical Metrology
This chapter describes the three physico-mechanical metrology streams; temperature and humidity, optical radiation and acoustic and vibration metrology. Among the seven base SI units, temperature and optical radiation encompasses the two SI units while acoustic comprises only derived parameters. Temperature metrology includes realization and dissemination of temperature and humidity parameters, optical radiation metrology includes parameters like illuminance, illuminance responsivity, luminous flux, luminance, colour temperature, colour coordinates and spectral irradiances. Acoustic metrology includes sound pressure, vibration amplitude, sound transmission and absorption coefficients. All the parameters are inter-connected to fulfil the human needs and endeavours and have immense importance in the socio-economic growth of the country. The contribution, insinuation, impact, significance and relevance of these PMPs in different sectors like health, process and manufacturing, lighting industry, building acoustics, SODAR system and noise mapping are described along with established measurement standards and facilities, CMCs, participation in key comparisons, gap analysis and futuristic requirements and suggestions. All these endeavours are carried for the inclusive industrial growth of the nation.
- 10 November 2020
- Published by Springer Nature
- p. 307-376
Physico-Mechanical Metrology
This chapter describes the three physico-mechanical metrology streams; temperature and humidity, optical radiation and acoustic and vibration metrology. Among the seven base SI units, temperature and optical radiation encompasses the two SI units while acoustic comprises only derived parameters. Temperature metrology includes realization and dissemination of temperature and humidity parameters, optical radiation metrology includes parameters like illuminance, illuminance responsivity, luminous flux, luminance, colour temperature, colour coordinates and spectral irradiances. Acoustic metrology includes sound pressure, vibration amplitude, sound transmission and absorption coefficients. All the parameters are inter-connected to fulfil the human needs and endeavours and have immense importance in the socio-economic growth of the country. The contribution, insinuation, impact, significance and relevance of these PMPs in different sectors like health, process and manufacturing, lighting industry, building acoustics, SODAR system and noise mapping are described along with established measurement standards and facilities, CMCs, participation in key comparisons, gap analysis and futuristic requirements and suggestions. All these endeavours are carried for the inclusive industrial growth of the nation.
- 15 March 2019
- Published by IOP Publishing in Journal of Physics: Condensed Matter
- Vol. 31 (20) , 205001
Elucidating the origin of magnetic ordering in ferroelectric BaTiO 3- d thin film via electronic structure modification
With the motive of unraveling the origin of native vacancy induced magnetization in ferroelectric perovskite oxide systems, here we explore the consequences of electronic structure modification in magnetic ordering of oxygen deficient epitaxial BaTiO thin films. Our adapted methodology employs state-of-the-art experimental approaches viz. photo-emission, photo-absorption spectroscopies, magnetometric measurements duly combined with first principles based theoretical methods within the frame work of density functional theory (DFT and DFT+ U ) calculations. Oxygen vacancy (O ) is observed leading partial population of Ti 3 d ( t 2 g ), which induces defect state in electronic structure near the Fermi level and reduces the band gap. The oxygen deficient BaTiO 2.75 film reveals Mott–Hubbard insulator characteristic, in contrast to the band gap insulating nature of the stoichiometric BaTiO 3 . The observed magnetic ordering is attributed to the asymmetric distribution of spin polarized charge density in the vicinity of O site, which originates unequal magnetic moment values at first and second nearest neighboring Ti sites, respectively. Hereby, we present an exclusive method for maneuvering the band gap and on-site electron correlation energy with consequences on magnetic properties of BaTiO system, which can open a gateway for designing novel single phase multiferroic system.
- 15 March 2019
- Published by IOP Publishing in Journal of Physics: Condensed Matter
- Vol. 31 (20) , 205001
Elucidating the origin of magnetic ordering in ferroelectric BaTiO 3- d thin film via electronic structure modification
With the motive of unraveling the origin of native vacancy induced magnetization in ferroelectric perovskite oxide systems, here we explore the consequences of electronic structure modification in magnetic ordering of oxygen deficient epitaxial BaTiO thin films. Our adapted methodology employs state-of-the-art experimental approaches viz. photo-emission, photo-absorption spectroscopies, magnetometric measurements duly combined with first principles based theoretical methods within the frame work of density functional theory (DFT and DFT+ U ) calculations. Oxygen vacancy (O ) is observed leading partial population of Ti 3 d ( t 2 g ), which induces defect state in electronic structure near the Fermi level and reduces the band gap. The oxygen deficient BaTiO 2.75 film reveals Mott–Hubbard insulator characteristic, in contrast to the band gap insulating nature of the stoichiometric BaTiO 3 . The observed magnetic ordering is attributed to the asymmetric distribution of spin polarized charge density in the vicinity of O site, which originates unequal magnetic moment values at first and second nearest neighboring Ti sites, respectively. Hereby, we present an exclusive method for maneuvering the band gap and on-site electron correlation energy with consequences on magnetic properties of BaTiO system, which can open a gateway for designing novel single phase multiferroic system.