Yi-Feng Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yi-Feng Lin has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Jing-Yuan Lin
Department of Electronic and Computer Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
9 shared publications - Hsuan-Yu Yueh
Department of Electronic and Computer Engineering, National Taiwan University of Science and Technology, Taipei 10607, Taiwan
5 shared publications - Pin-Hsien Liu
Department of Electronic and Computer Engineering, National Taiwan University of Science and Technology, Taipei 10607, Taiwan
5 shared publications - Kuan-Hung Chen
Department of Electronic and Computer Engineering, National Taiwan University of Science and Technology, Taipei 10607, Taiwan
2 shared publications Chuan Ting Chen
Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei City, Taiwan
1 shared publicationChuan-Ting Chen
Department of Electronic and Computer Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
1 shared publication
Latest Publications
- Open Access
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 608-617
A Novel Hybrid Cascaded and Stacked Coupled Inductor Boost Converter With Active Clamping Zero-Voltage Switching
The application of a traditional boost converter requires a wide duty cycle for high boost voltage gain. The wide duty cycle has the problem of a high current peak due to a large input current. The Coupled inductor based boost converter achieves a high step-up voltage ratio and reduce the problem of wide duty cycle. However, the basic coupled inductor converters have some disadvantages. Such as high voltage spike on the switch caused by a leakage inductance and the problem of large input current still cannot effectively improve. This paper aims to address these problems. The proposed topology used a coupled inductor to achieve high step-up voltage ratio. The designed voltage stabilizing capacitor loop reduces the current peak value of the main coupling inductor. Active clamping is used to suppress voltage spikes and implement zero-voltage switching (ZVS) of the switch to improve efficiency. This study describes the working principle and time domain analysis of this topology. Detailed design of components and propose the best design process. A prototype converter with an output power of 400 W was constructed. Conducted at a DC input voltage of 40 VDC and a DC output voltage of 400 VDC. Experimental results show that the maximum conversion efficiency is 94.6%.
- 11 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 608-617
Open AccessA Novel Hybrid Cascaded and Stacked Coupled Inductor Boost Converter With Active Clamping Zero-Voltage Switching
The application of a traditional boost converter requires a wide duty cycle for high boost voltage gain. The wide duty cycle has the problem of a high current peak due to a large input current. The Coupled inductor based boost converter achieves a high step-up voltage ratio and reduce the problem of wide duty cycle. However, the basic coupled inductor converters have some disadvantages. Such as high voltage spike on the switch caused by a leakage inductance and the problem of large input current still cannot effectively improve. This paper aims to address these problems. The proposed topology used a coupled inductor to achieve high step-up voltage ratio. The designed voltage stabilizing capacitor loop reduces the current peak value of the main coupling inductor. Active clamping is used to suppress voltage spikes and implement zero-voltage switching (ZVS) of the switch to improve efficiency. This study describes the working principle and time domain analysis of this topology. Detailed design of components and propose the best design process. A prototype converter with an output power of 400 W was constructed. Conducted at a DC input voltage of 40 VDC and a DC output voltage of 400 VDC. Experimental results show that the maximum conversion efficiency is 94.6%.
- Open Access
Dual-Coupled-Inductor-Based High-Step-Up Boost Converter with Active-Clamping and Zero-Voltage Switching
Many applications, such as photovoltaic systems, uninterruptible power supplies, and automobile headlamps, need a high step-up DC–DC converter without isolation. The conventional boost converter has the advantages of simple topology and easy control. However, it has some shortcomings, such as insufficient step-up voltage ratio and poor efficiency when operating at large duty-cycle conditions. One of the popular topologies used to overcome these problems is the coupled-inductor boost converter. It utilizes the turn ratio of the coupled inductor to realize a higher step-up voltage ratio. The drawback is that the leakage inductance of the coupled inductor causes a huge voltage spike when the power switches are turned off. Moreover, because coupled inductors are characterized by their large volume and high profile, a conventional coupled-inductor boost converter is unsuited for photovoltaic systems, such as the solar microinverter. This study proposes a novel high-step-up boost converter to solve these problems. This proposed converter uses dual coupled inductors instead of the conventional coupled-inductor boost converter. The secondary side of the coupled inductor is connected in series to increase the step-up voltage ratio. The proposed converter utilizes active clamping to achieve zero-voltage switching (ZVS) for suppressing voltage spike and improving conversion efficiency. In addition, low-profile designs can be fulfilled easily for solar microinverters. The proposed converter and its control method are introduced. The operation principle, circuit characteristics, and circuit analysis are presented. A prototype converter with 300 W output power 25–40 VDC input voltage and 200 VDC output voltage was tested. All functions, including high step-up voltage ratio, ZVS, and active clamping, were achieved, and the highest efficiency was around at 94.7%.
Open AccessDual-Coupled-Inductor-Based High-Step-Up Boost Converter with Active-Clamping and Zero-Voltage Switching
Many applications, such as photovoltaic systems, uninterruptible power supplies, and automobile headlamps, need a high step-up DC–DC converter without isolation. The conventional boost converter has the advantages of simple topology and easy control. However, it has some shortcomings, such as insufficient step-up voltage ratio and poor efficiency when operating at large duty-cycle conditions. One of the popular topologies used to overcome these problems is the coupled-inductor boost converter. It utilizes the turn ratio of the coupled inductor to realize a higher step-up voltage ratio. The drawback is that the leakage inductance of the coupled inductor causes a huge voltage spike when the power switches are turned off. Moreover, because coupled inductors are characterized by their large volume and high profile, a conventional coupled-inductor boost converter is unsuited for photovoltaic systems, such as the solar microinverter. This study proposes a novel high-step-up boost converter to solve these problems. This proposed converter uses dual coupled inductors instead of the conventional coupled-inductor boost converter. The secondary side of the coupled inductor is connected in series to increase the step-up voltage ratio. The proposed converter utilizes active clamping to achieve zero-voltage switching (ZVS) for suppressing voltage spike and improving conversion efficiency. In addition, low-profile designs can be fulfilled easily for solar microinverters. The proposed converter and its control method are introduced. The operation principle, circuit characteristics, and circuit analysis are presented. A prototype converter with 300 W output power 25–40 VDC input voltage and 200 VDC output voltage was tested. All functions, including high step-up voltage ratio, ZVS, and active clamping, were achieved, and the highest efficiency was around at 94.7%.
- Open Access
- 30 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 57655-57664
Design of Boost-Type Power Factor Correction With Stepped Air-Gap Ferrite Inductor for Peak-Power-Load Condition
This paper presents the designed method and the implementation of stepped air-gap ferrite inductor applied in power factor correction (PFC). Conventionally, the input inductor of the PFC has a designed consideration on the maximum output power; thus, designing the PFC for peak-power-load conditions results in a very large inductor. The proposed designed method improves the load-carrying capability without increasing the volume of the inductor when the PFC is operating in peak-power-load conditions. The stepped air-gap ferrite inductor maintains the inductance in the rated-full-load and sustains the peak-power-load conditions with the lower inductance. Compared with the convectional ferrite inductor, the proposed method can maintain the size and the efficiency of the power supply, and promote the power-carrying ability. The detailed analysis and the design of the proposed method are described. Experimental results are recorded and evaluated by a prototype PFC with an AC input voltage of 110–264 VAC and a DC output voltage of 384 VDC. Finally, the volume of input inductor is kept with 40950 mm2, the efficiency is also same compared with the conventional inductor, and the load-carrying capability of the converter is promoted from the normal rated power of 1 kW to the peak power load of 2 kW.
- 30 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 57655-57664
Open AccessDesign of Boost-Type Power Factor Correction With Stepped Air-Gap Ferrite Inductor for Peak-Power-Load Condition
This paper presents the designed method and the implementation of stepped air-gap ferrite inductor applied in power factor correction (PFC). Conventionally, the input inductor of the PFC has a designed consideration on the maximum output power; thus, designing the PFC for peak-power-load conditions results in a very large inductor. The proposed designed method improves the load-carrying capability without increasing the volume of the inductor when the PFC is operating in peak-power-load conditions. The stepped air-gap ferrite inductor maintains the inductance in the rated-full-load and sustains the peak-power-load conditions with the lower inductance. Compared with the convectional ferrite inductor, the proposed method can maintain the size and the efficiency of the power supply, and promote the power-carrying ability. The detailed analysis and the design of the proposed method are described. Experimental results are recorded and evaluated by a prototype PFC with an AC input voltage of 110–264 VAC and a DC output voltage of 384 VDC. Finally, the volume of input inductor is kept with 40950 mm2, the efficiency is also same compared with the conventional inductor, and the load-carrying capability of the converter is promoted from the normal rated power of 1 kW to the peak power load of 2 kW.
- 20 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 4 (1) , 348-356
Variable-Frequency and Phase-Shift With Synchronous Rectification Advance On-Time Hybrid Control of LLC Resonant Converter for Electric Vehicles Charger
The LLC resonant converter has been widely used in the power supply industry, such as server power, TV power, and adapter, because this converter can realize the zero-voltage switching (ZVS) at the power MOSFETs of the primary side. Thus, the switch losses can be decreased, and the conversion efficiency can also be improved. The electric vehicle (EV) charger has been recently widely used in research and development. However, designing LLC resonant converters for the wide battery voltage range is difficult because this converter is usually utilized in pulse frequency modulation (PFM) to regulate the output voltage. This converter will also be limited on the low operating frequency range for the high conversion efficiency due to the switching frequency. By contrast, the phase-shift modulation (PSM) control for the wide output voltage range has been used at LLC resonant converters. However, the ZVS will be lost due to the lagging leg of the LLC resonant converter when the phase-shift angle is remarkably excessive. The burst-mode control has also been proposed for the converter to regulate the output voltage and maintain high conversion efficiency at light-load conditions. Therefore, this paper utilized the combination of PFM, PSM and burst-mode control for the LLC resonant converter operating at the wide output voltage range for EV charge applications. Furthermore, this paper proposed a synchronous rectification advance on-time control for PFM control, which can help address the ZVS at the lagging leg when the phase-shift angle is excessive. Detailed analysis and design of this control method are also described. The performance evaluation of the proposed LLC resonant converter with hybrid control was finally realized under the following conditions: 3.75 kW, DC input voltage of 400 VDC, DC output voltage of 75–475 VDC and maximum conversion efficiency around 97%.
- 20 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 4 (1) , 348-356
Variable-Frequency and Phase-Shift With Synchronous Rectification Advance On-Time Hybrid Control of LLC Resonant Converter for Electric Vehicles Charger
The LLC resonant converter has been widely used in the power supply industry, such as server power, TV power, and adapter, because this converter can realize the zero-voltage switching (ZVS) at the power MOSFETs of the primary side. Thus, the switch losses can be decreased, and the conversion efficiency can also be improved. The electric vehicle (EV) charger has been recently widely used in research and development. However, designing LLC resonant converters for the wide battery voltage range is difficult because this converter is usually utilized in pulse frequency modulation (PFM) to regulate the output voltage. This converter will also be limited on the low operating frequency range for the high conversion efficiency due to the switching frequency. By contrast, the phase-shift modulation (PSM) control for the wide output voltage range has been used at LLC resonant converters. However, the ZVS will be lost due to the lagging leg of the LLC resonant converter when the phase-shift angle is remarkably excessive. The burst-mode control has also been proposed for the converter to regulate the output voltage and maintain high conversion efficiency at light-load conditions. Therefore, this paper utilized the combination of PFM, PSM and burst-mode control for the LLC resonant converter operating at the wide output voltage range for EV charge applications. Furthermore, this paper proposed a synchronous rectification advance on-time control for PFM control, which can help address the ZVS at the lagging leg when the phase-shift angle is excessive. Detailed analysis and design of this control method are also described. The performance evaluation of the proposed LLC resonant converter with hybrid control was finally realized under the following conditions: 3.75 kW, DC input voltage of 400 VDC, DC output voltage of 75–475 VDC and maximum conversion efficiency around 97%.
- 9 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (5) , 6033-6044
Design and Analysis of LLC Resonant Converter With Valley Switching Control for Light-Load Conditions
The LLC converter has been widely used in the power supply industry for its high conversion efficiency. When the output load is low, the LLC resonant converter will substantially increase the operating frequency, thereby reducing the conversion efficiency and exceeding the limited operating frequency of the specification. Thus, burst-mode control is applied to increase the ability of regulation at light-load conditions. Even so, the switching period of power-switches still occurs at a high switching frequency. Burst-mode control will also result in an extremely low-frequency output voltage ripple. In this study, a valley switching control (VSC) for the LLC resonant converter at light-load conditions is proposed. The VSC control strategy maintains the output voltage by modulating the pulse-width signals of drivers, and achieves valley switching by modulating the switching frequency. Thus, the VSC strategy can reduces the operating frequency compared with the frequency modulation strategy. Compared with burst-mode operations, the proposed VSC effectively reduces the switching loss and has the advantages of the high-frequency output voltage ripple. The VSC increases the efficiency and the power quality of the converter. Detailed analysis and design of the proposed method are described. Experimental results are recorded for a prototype converter with a DC input voltage of 400-VDC, an output voltage of 48-VDC, and an output current of 12.5-A.
- 9 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (5) , 6033-6044
Design and Analysis of LLC Resonant Converter With Valley Switching Control for Light-Load Conditions
The LLC converter has been widely used in the power supply industry for its high conversion efficiency. When the output load is low, the LLC resonant converter will substantially increase the operating frequency, thereby reducing the conversion efficiency and exceeding the limited operating frequency of the specification. Thus, burst-mode control is applied to increase the ability of regulation at light-load conditions. Even so, the switching period of power-switches still occurs at a high switching frequency. Burst-mode control will also result in an extremely low-frequency output voltage ripple. In this study, a valley switching control (VSC) for the LLC resonant converter at light-load conditions is proposed. The VSC control strategy maintains the output voltage by modulating the pulse-width signals of drivers, and achieves valley switching by modulating the switching frequency. Thus, the VSC strategy can reduces the operating frequency compared with the frequency modulation strategy. Compared with burst-mode operations, the proposed VSC effectively reduces the switching loss and has the advantages of the high-frequency output voltage ripple. The VSC increases the efficiency and the power quality of the converter. Detailed analysis and design of the proposed method are described. Experimental results are recorded for a prototype converter with a DC input voltage of 400-VDC, an output voltage of 48-VDC, and an output current of 12.5-A.
- Open Access
Analysis and Design of Three-Phase LLC Resonant Converter with Matrix Transformers
This study presents the topology of a three-phase LLC resonant converter with matrix transformers. The three-phase LLC resonant converter has the advantages of conventional LLC resonant converters, including zero-voltage switching at the primary side, zero-current switching at the secondary side, high-frequency feasibility, and high efficiency. Moreover, it has additional advantages that differ from conventional LLC, including low output capacitor current ripple, natural current sharing in three resonant currents, and a high power level. As a result of the above mentioned characteristics, LLC topology has been used in many electric vehicle charging systems, server power systems, and other high-power applications. However, as the power level becomes higher and higher, the input voltage is usually too high to reduce conduction loss, and the output current also increases. This situation makes transformer design more difficult. The increasing current means more core and copper loss, and the heat dissipation of the transformer becomes more difficult. Matrix transformer technology can improve this problem directly and simply. By utilizing matrix transformers, which are primary series connected and secondary parallel connected, the primary voltage stress and secondary current stress of the transformers can be reduced, and the output current can be distributed. The analysis of the proposed converter in this study includes a circuit operation introduction, a time-domain analysis, calculation of the transfer ratio curve in the frequency domain, and a loss analysis. The theoretical analysis and performance of the proposed converter are verified. A three-phase LLC resonant converter with matrix transformers prototype is built with a high input voltage of 800-VDC and high output current of 200-A. The output voltage is 100-VDC. The waveform and efficiency data will be shown in the experimental results.
Open AccessAnalysis and Design of Three-Phase LLC Resonant Converter with Matrix Transformers
This study presents the topology of a three-phase LLC resonant converter with matrix transformers. The three-phase LLC resonant converter has the advantages of conventional LLC resonant converters, including zero-voltage switching at the primary side, zero-current switching at the secondary side, high-frequency feasibility, and high efficiency. Moreover, it has additional advantages that differ from conventional LLC, including low output capacitor current ripple, natural current sharing in three resonant currents, and a high power level. As a result of the above mentioned characteristics, LLC topology has been used in many electric vehicle charging systems, server power systems, and other high-power applications. However, as the power level becomes higher and higher, the input voltage is usually too high to reduce conduction loss, and the output current also increases. This situation makes transformer design more difficult. The increasing current means more core and copper loss, and the heat dissipation of the transformer becomes more difficult. Matrix transformer technology can improve this problem directly and simply. By utilizing matrix transformers, which are primary series connected and secondary parallel connected, the primary voltage stress and secondary current stress of the transformers can be reduced, and the output current can be distributed. The analysis of the proposed converter in this study includes a circuit operation introduction, a time-domain analysis, calculation of the transfer ratio curve in the frequency domain, and a loss analysis. The theoretical analysis and performance of the proposed converter are verified. A three-phase LLC resonant converter with matrix transformers prototype is built with a high input voltage of 800-VDC and high output current of 200-A. The output voltage is 100-VDC. The waveform and efficiency data will be shown in the experimental results.
- Open Access
Analysis of Three-Phase Wye-Delta Connected LLC
Three-phase wye–delta LLC topology is suitable for voltage step down and high output current, and has been used in the industry for some time, e.g., for server power and EV charger. However, no comprehensive circuit analysis has been performed for three-phase wye–delta LLC. This paper provides complete analysis methods for three-phase wye–delta LLC. The analysis methods include circuit operation, time domain analysis, frequency domain analysis, and state–plane analysis. Circuit operation helps determine the circuit composition and operation sequence. Time domain analysis helps understand the detail operation, equivalent circuit model, and circuit equation. Frequency domain analysis helps obtain the curve of the transfer function and assists in circuit design. State–plane analysis is used for optimal trajectory control (OTC). These analyses not only can calculate the voltage/current stress, but can also help design three-phase wye-delta connected LLC and provide the OTC control reference. In addition, this paper uses PSIM simulation to verify the correctness of analysis. At the end, a 5-kW three-phase wye–delta LLC prototype is realized. The specification of the prototype is a DC input voltage of 380 V and output voltage/current of 48 V/105 A. The peak efficiency is 96.57%.
Open AccessAnalysis of Three-Phase Wye-Delta Connected LLC
Three-phase wye–delta LLC topology is suitable for voltage step down and high output current, and has been used in the industry for some time, e.g., for server power and EV charger. However, no comprehensive circuit analysis has been performed for three-phase wye–delta LLC. This paper provides complete analysis methods for three-phase wye–delta LLC. The analysis methods include circuit operation, time domain analysis, frequency domain analysis, and state–plane analysis. Circuit operation helps determine the circuit composition and operation sequence. Time domain analysis helps understand the detail operation, equivalent circuit model, and circuit equation. Frequency domain analysis helps obtain the curve of the transfer function and assists in circuit design. State–plane analysis is used for optimal trajectory control (OTC). These analyses not only can calculate the voltage/current stress, but can also help design three-phase wye-delta connected LLC and provide the OTC control reference. In addition, this paper uses PSIM simulation to verify the correctness of analysis. At the end, a 5-kW three-phase wye–delta LLC prototype is realized. The specification of the prototype is a DC input voltage of 380 V and output voltage/current of 48 V/105 A. The peak efficiency is 96.57%.
- 4 May 2021
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 44 (4) , 388-398
Interleaved LLC half-bridge series resonant converter with integrated transformer
High efficiency and simple structure are the main reasons for the widespread use of LLC converters. Nowadays, the application of LLC converters is still in development. In general, increasing the power level to use a parallel converter is quite popular. However, this method uses a separate transformer, which will lead to an obvious decrease in power density. Moreover, the separate transformer will also cause current imbalance due to the error of the magnetic material characteristic. Therefore, this study proposes an integrated transformer for a conventional interleaved LLC converter. This proposed structure can effectively increase the power density and decrease the problem of current imbalance. The operating principle of the interleaved LLC converter and an analysis of the integrated transformer are presented. Finally, experimental results are recorded for a prototype converter. The specifications are as follows: DC input voltage is 380 VDC, output voltage is 12 VDC, maximum output current is 50 A, output power is 600 W, and maximum conversion efficiency is approximately 95.5%.
- 4 May 2021
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 44 (4) , 388-398
Interleaved LLC half-bridge series resonant converter with integrated transformer
High efficiency and simple structure are the main reasons for the widespread use of LLC converters. Nowadays, the application of LLC converters is still in development. In general, increasing the power level to use a parallel converter is quite popular. However, this method uses a separate transformer, which will lead to an obvious decrease in power density. Moreover, the separate transformer will also cause current imbalance due to the error of the magnetic material characteristic. Therefore, this study proposes an integrated transformer for a conventional interleaved LLC converter. This proposed structure can effectively increase the power density and decrease the problem of current imbalance. The operating principle of the interleaved LLC converter and an analysis of the integrated transformer are presented. Finally, experimental results are recorded for a prototype converter. The specifications are as follows: DC input voltage is 380 VDC, output voltage is 12 VDC, maximum output current is 50 A, output power is 600 W, and maximum conversion efficiency is approximately 95.5%.
- Open Access
Current Sharing Control of an Interleaved Three-Phase Series-Resonant Converter with Phase Shift Modulation
Recently, three-phase series-resonant converters (SRCs) have been proposed for high power applications. Three-phase SRCs can achieve zero-voltage-switching (ZVS) of the primary power switches and regulate the output voltage by pulse-frequency modulation. The interleaving technique is also a conventional method for DC-DC converters to achieve a high power level, reducing the output voltage ripples due to operating out of phase at the same frequency between the two converters. However, an interleaved three-phase SRC cannot easily synchronize switching instants between the two modules due to the component tolerances of circuits. In the proposed control method, phase shift modulation (PSM) is used to solve the output current imbalance caused by component tolerances. The power switches of the converter can also maintain synchronizing switching instants between the two modules. Therefore, the lower output voltage ripple can be achieved. A detailed analysis and design of this new control method for interleaved three-phase SRCs are described. Finally, prototype converters with a 2.4 kW total output were built and successfully tested to verify the feasibility of the current sharing modulation.
Open AccessCurrent Sharing Control of an Interleaved Three-Phase Series-Resonant Converter with Phase Shift Modulation
Recently, three-phase series-resonant converters (SRCs) have been proposed for high power applications. Three-phase SRCs can achieve zero-voltage-switching (ZVS) of the primary power switches and regulate the output voltage by pulse-frequency modulation. The interleaving technique is also a conventional method for DC-DC converters to achieve a high power level, reducing the output voltage ripples due to operating out of phase at the same frequency between the two converters. However, an interleaved three-phase SRC cannot easily synchronize switching instants between the two modules due to the component tolerances of circuits. In the proposed control method, phase shift modulation (PSM) is used to solve the output current imbalance caused by component tolerances. The power switches of the converter can also maintain synchronizing switching instants between the two modules. Therefore, the lower output voltage ripple can be achieved. A detailed analysis and design of this new control method for interleaved three-phase SRCs are described. Finally, prototype converters with a 2.4 kW total output were built and successfully tested to verify the feasibility of the current sharing modulation.
- Open Access
A Novel Multi-Element Resonant Converter with Self-Driven Synchronous Rectification
This paper proposes a novel multi-element resonant converter with self-driven synchronous rectification (SR). The proposed resonant converter can achieve a zero-voltage-switching (ZVS) operation from light load to full load, meanwhile, the zero-current-switching (ZCS) can achieve rectifiers of a secondary-side. Therefore, the switching losses can be significantly reduced. Compared with an LLC resonant converter, the proposed resonant converter can be effective to decrease the circulating energy through the primary-side of the transformer to output a load and provide a wide voltage gain range for over-current protection as well as decreasing the inrush current under the start-up condition. Moreover, the proposed converter uses a simple current detection scheme to control the synchronous rectification switches. A detailed analysis and design of this novel multi-element resonant converter with self-driven synchronous rectification is described. Finally, a DC input voltage of 380-VDC and an output voltage/current of 12-VDC/54-A for the resonant converter prototype is built to verify the theoretical analysis and performance of the proposed converter.
Open AccessA Novel Multi-Element Resonant Converter with Self-Driven Synchronous Rectification
This paper proposes a novel multi-element resonant converter with self-driven synchronous rectification (SR). The proposed resonant converter can achieve a zero-voltage-switching (ZVS) operation from light load to full load, meanwhile, the zero-current-switching (ZCS) can achieve rectifiers of a secondary-side. Therefore, the switching losses can be significantly reduced. Compared with an LLC resonant converter, the proposed resonant converter can be effective to decrease the circulating energy through the primary-side of the transformer to output a load and provide a wide voltage gain range for over-current protection as well as decreasing the inrush current under the start-up condition. Moreover, the proposed converter uses a simple current detection scheme to control the synchronous rectification switches. A detailed analysis and design of this novel multi-element resonant converter with self-driven synchronous rectification is described. Finally, a DC input voltage of 380-VDC and an output voltage/current of 12-VDC/54-A for the resonant converter prototype is built to verify the theoretical analysis and performance of the proposed converter.