Cihan Özorak
Research Subjects
Cihan Özorak has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Serkan Islak
Kastamonu Univ, Fac Engn & Architecture, Dept Mech Engn, Kastamonu, Turkiye
5 shared publications - Mehmet Akkaş
Department of Mechanical Engineering, Faculty of Engineering and Architecture, Kastamonu University, Kastamonu 37150, Turkey
3 shared publications - Ugur Caligulu
Fırat universitesi
3 shared publications - Husain Rajab Husain Hraam
Department of Mechanical Engineering, Faculty of Engineering, Elmergib University, Al-Khoms, Libya
2 shared publications Kastamonu University
2 shared publicationsAdıyaman University
1 shared publication
Latest Publications
- Open Access
- 31 December 2024
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 12 (4) , 1035-1046
Microstructural, mechanical, and corrosion properties of S355J2 structural steels joined by MIG welding
In this study, the microstructural, mechanical, and corrosion properties of S355J2 structural steels welded by metal inert gas (MIG) welding method were investigated. Single surface and double surface welded structures were formed by MIG welding method using 2 different amperage values (200A, and 260A). The microhardness, tensile strength, corrosion and microstructure properties of the welded specimens were investigated. The structural and mechanical effects of different current values used on the material were analysed. Microstructure investigations show that fine grained structures start to coarsen and grain boundaries start to decrease due to welding heat input in the HAZ region. The highest hardness value was measured in the welded joint at 260A value in single surface welding due to rapid cooling and rapid solidification. Increases in yield strength and tensile strength were determined with increasing welding current and in the double-sided welding procedure. In the potentiodynamic corrosion test carried out in HCl solution, it was determined that the double-sided welded joint at 260A welding amperage and the double-sided welded joint at 260A was the most resistant to corrosion among the samples subjected to corrosion tests.
- 31 December 2024
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 12 (4) , 1035-1046
Open AccessMicrostructural, mechanical, and corrosion properties of S355J2 structural steels joined by MIG welding
In this study, the microstructural, mechanical, and corrosion properties of S355J2 structural steels welded by metal inert gas (MIG) welding method were investigated. Single surface and double surface welded structures were formed by MIG welding method using 2 different amperage values (200A, and 260A). The microhardness, tensile strength, corrosion and microstructure properties of the welded specimens were investigated. The structural and mechanical effects of different current values used on the material were analysed. Microstructure investigations show that fine grained structures start to coarsen and grain boundaries start to decrease due to welding heat input in the HAZ region. The highest hardness value was measured in the welded joint at 260A value in single surface welding due to rapid cooling and rapid solidification. Increases in yield strength and tensile strength were determined with increasing welding current and in the double-sided welding procedure. In the potentiodynamic corrosion test carried out in HCl solution, it was determined that the double-sided welded joint at 260A welding amperage and the double-sided welded joint at 260A was the most resistant to corrosion among the samples subjected to corrosion tests.
- Open Access
- 24 October 2023
- Published by INESEG Yayincilik in European Journal of Technic
- Vol. 13 (2) , 88-93
Production of CuNiSi Composites by Powder Metallurgy Method: Effects of Ti on the Microstructural and Corrosion Properties
In this study, composite samples were produced by supplementing the CuNiSi powder mixture with Ti particles at different weight ratios using the powder metallurgy (PM) method. The prepared CuNiSi and Ti powder mixtures were turned into pellets by cold pressing under 500 MPa pressure. The pelletized samples were subjected to sintering in an atmosphere-controlled oven at 900 ℃ for 2 hours. Scanning electron microscopy (SEM-EDS), SEM-Mapping and corrosion experiments were performed to determine the microstructures of the produced samples. From the microstructure results, it was determined that Ti particles were distributed homogeneously within the structure. As the amount of Ti increased, the resistance of the composite to corrosion increased. In addition to that, as the amount of Ti increased, the resistance of the composite to corrosion decreased.
- 24 October 2023
- Published by INESEG Yayincilik in European Journal of Technic
- Vol. 13 (2) , 88-93
Open AccessProduction of CuNiSi Composites by Powder Metallurgy Method: Effects of Ti on the Microstructural and Corrosion Properties
In this study, composite samples were produced by supplementing the CuNiSi powder mixture with Ti particles at different weight ratios using the powder metallurgy (PM) method. The prepared CuNiSi and Ti powder mixtures were turned into pellets by cold pressing under 500 MPa pressure. The pelletized samples were subjected to sintering in an atmosphere-controlled oven at 900 ℃ for 2 hours. Scanning electron microscopy (SEM-EDS), SEM-Mapping and corrosion experiments were performed to determine the microstructures of the produced samples. From the microstructure results, it was determined that Ti particles were distributed homogeneously within the structure. As the amount of Ti increased, the resistance of the composite to corrosion increased. In addition to that, as the amount of Ti increased, the resistance of the composite to corrosion decreased.
- 25 January 2022
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 48 (4) , 1593-1613
New N,N'-bis(thioamido)thiocarbohydrazones and carbohydrazones: synthesis, structure characterization, antioxidant activity, corrosion inhibitors and DFT studies
- 25 January 2022
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 48 (4) , 1593-1613
New N,N'-bis(thioamido)thiocarbohydrazones and carbohydrazones: synthesis, structure characterization, antioxidant activity, corrosion inhibitors and DFT studies
- 1 January 2019
- Published by MIM Research Group in Research on Engineering Structures and Materials
Microstructure, hardness and biocompatibility properties of ceramic based coatings produced by plasma spray method
Microstructure, hardness and biocompatibility properties of ceramic based coatings produced by plasma spray method
- 1 January 2019
- Published by MIM Research Group in Research on Engineering Structures and Materials
Microstructure, hardness and biocompatibility properties of ceramic based coatings produced by plasma spray method
Microstructure, hardness and biocompatibility properties of ceramic based coatings produced by plasma spray method
- 1 January 2019
- Published by MIM Research Group in Research on Engineering Structures and Materials
Electrical conductivity, microstructure and wear properties of Cu-Mo coatings
Electrical conductivity, microstructure and wear properties of Cu-Mo coatings
- 1 January 2019
- Published by MIM Research Group in Research on Engineering Structures and Materials
Electrical conductivity, microstructure and wear properties of Cu-Mo coatings
Electrical conductivity, microstructure and wear properties of Cu-Mo coatings
- 28 December 2018
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 14 (4) , 465-469
Corrosion and Wear Properties of Cu-TiC Composites Produced by Hot Pressing Technique
Cu-xTiC (x=0, 1, 5, 10 and 15 wt.%) composites were prepared by hot pressing (HP) technique. The microstructure, corrosion and wear features of Cu matrix composites (CMCs) were investigated. The wear surfaces and microstructure of the CMCs were analyzed using SEM-EDS. Phases of samples were identified by means of XRD. Hardness measurements of the composites were made using a microhardness device. Hardness tests showed that the hardness tends to increase with increasing TiC amount. Wear properties of the CMCs were determined using ball-on-disc method. Significant decreases in wear rates were observed in composites reinforced with TiC. The corrosion properties of the composites were characterized by potentiostatic polarization test. Corrosion results showed that the corrosion resistance of the composites decreased with the increase of TiC content in Cu. Among the composites, Cu-1% TiC has the best corrosion resistance.
- 28 December 2018
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 14 (4) , 465-469
Corrosion and Wear Properties of Cu-TiC Composites Produced by Hot Pressing Technique
Cu-xTiC (x=0, 1, 5, 10 and 15 wt.%) composites were prepared by hot pressing (HP) technique. The microstructure, corrosion and wear features of Cu matrix composites (CMCs) were investigated. The wear surfaces and microstructure of the CMCs were analyzed using SEM-EDS. Phases of samples were identified by means of XRD. Hardness measurements of the composites were made using a microhardness device. Hardness tests showed that the hardness tends to increase with increasing TiC amount. Wear properties of the CMCs were determined using ball-on-disc method. Significant decreases in wear rates were observed in composites reinforced with TiC. The corrosion properties of the composites were characterized by potentiostatic polarization test. Corrosion results showed that the corrosion resistance of the composites decreased with the increase of TiC content in Cu. Among the composites, Cu-1% TiC has the best corrosion resistance.
- Open Access
- 1 January 2018
- Published by Hitit University in Hittite Journal of Science and Engineering
Microstructure, corrosion and wear properties of FeCrNiMo based coating produced on AISI 1040 steel by using laser coating technique
This study aims to investigate microstructure, hardness, corrosion and wear properties of FeCrNiMo-based coating produced on AISI 1040 steel by using laser welding method. Microstructure properties and phase formation were examined by SEM-EDS and XRD. The hardness measurement was made by using a microhardness device along a line from the upper surface of the coating to the substrate. The wear tests of both the substrate and coating layer were made with a scratch test device. SEM examinations showed that the coating layer had a dendritic microstructure and was uniformly bonded to the substrate. The coating layer was harder than the substrate. According to wear tests, the friction coefficient of the coating layer was lower compared to the substrate. Substrate and coating layer were immersed in an aqueous solution of NaCl for potentiodynamic measurements. Corrosion results showed that coating of the AISI 1040 steel with FeCrNiMo increased the corrosion resistance. Keywords: Laser coating; Microstructure; Wear; Corrosion DOI: 10.17350/HJSE19030000098 Full Text:
- 1 January 2018
- Published by Hitit University in Hittite Journal of Science and Engineering
Open AccessMicrostructure, corrosion and wear properties of FeCrNiMo based coating produced on AISI 1040 steel by using laser coating technique
This study aims to investigate microstructure, hardness, corrosion and wear properties of FeCrNiMo-based coating produced on AISI 1040 steel by using laser welding method. Microstructure properties and phase formation were examined by SEM-EDS and XRD. The hardness measurement was made by using a microhardness device along a line from the upper surface of the coating to the substrate. The wear tests of both the substrate and coating layer were made with a scratch test device. SEM examinations showed that the coating layer had a dendritic microstructure and was uniformly bonded to the substrate. The coating layer was harder than the substrate. According to wear tests, the friction coefficient of the coating layer was lower compared to the substrate. Substrate and coating layer were immersed in an aqueous solution of NaCl for potentiodynamic measurements. Corrosion results showed that coating of the AISI 1040 steel with FeCrNiMo increased the corrosion resistance. Keywords: Laser coating; Microstructure; Wear; Corrosion DOI: 10.17350/HJSE19030000098 Full Text:
- Open Access
- 1 January 2015
- Published by Pamukkale University in Pamukkale University Journal of Engineering Sciences
- Vol. 21 (8) , 344-347
Microstructure Characterization of WCCo-Mo Based Coatings Produced Using High Velocity Oxygen Fuel
Bu çalışma, yüksek hızlı oksi yakıt (HVOF) ısıl püskürtme yöntemi ile SAE 4140 çeliği üzerinde üretilen WCCo-Mo kompozit kaplamaların mikroyapısal özelliklerini araştırmak için yapılmıştır. Bu amaç için WCCo tozlarına ilave edilen Mo miktarı % ağ. 10, 20, 30 ve 40 olarak değiştirilmiştir. Kaplamalar, faz bileşimi, mikroyapı ve sertlik özellikleri açısından karşılaştırılmıştır. Kaplama tabakalarının faz bileşimi ve mikroyapısı X-ışını difraktogramı (XRD) ve taramalı elektron mikroskobu (SEM) ile incelenmiştir. XRD sonuçları, WCCo-Mo kaplama tabakasının WC, W2C, Co3W3C, Mo2C, MoO2, Mo ve Co fazlardan oluştuğunu göstermiştir. Kaplamaların sertliği Mo artışı ile artmıştır.The present study has been carried out in order to investigate the microstructural properties of WCCo-Mo composite coatings deposited onto a SAE 4140 steel substrate by high velocity oxygen fuel (HVOF) thermal spray. For this purpose, the Mo quantity added to the WCCo was changed as 10, 20, 30 and 40 wt. % percents. The coatings are compared in terms of their phase composition, microstructure and hardness. Phase compound and microstructure of coating layers were examined using X-ray diffractometer (XRD) and scanning electron microscope (SEM). XRD results showed that WCCo-Mo composite coatings were mainly composed of WC, W2C, Co3W3C, Mo2C, MoO2, Mo and Co phases. The average hardness of the coatings increased with increasing Mo content
- 1 January 2015
- Published by Pamukkale University in Pamukkale University Journal of Engineering Sciences
- Vol. 21 (8) , 344-347
Open AccessMicrostructure Characterization of WCCo-Mo Based Coatings Produced Using High Velocity Oxygen Fuel
Bu çalışma, yüksek hızlı oksi yakıt (HVOF) ısıl püskürtme yöntemi ile SAE 4140 çeliği üzerinde üretilen WCCo-Mo kompozit kaplamaların mikroyapısal özelliklerini araştırmak için yapılmıştır. Bu amaç için WCCo tozlarına ilave edilen Mo miktarı % ağ. 10, 20, 30 ve 40 olarak değiştirilmiştir. Kaplamalar, faz bileşimi, mikroyapı ve sertlik özellikleri açısından karşılaştırılmıştır. Kaplama tabakalarının faz bileşimi ve mikroyapısı X-ışını difraktogramı (XRD) ve taramalı elektron mikroskobu (SEM) ile incelenmiştir. XRD sonuçları, WCCo-Mo kaplama tabakasının WC, W2C, Co3W3C, Mo2C, MoO2, Mo ve Co fazlardan oluştuğunu göstermiştir. Kaplamaların sertliği Mo artışı ile artmıştır.The present study has been carried out in order to investigate the microstructural properties of WCCo-Mo composite coatings deposited onto a SAE 4140 steel substrate by high velocity oxygen fuel (HVOF) thermal spray. For this purpose, the Mo quantity added to the WCCo was changed as 10, 20, 30 and 40 wt. % percents. The coatings are compared in terms of their phase composition, microstructure and hardness. Phase compound and microstructure of coating layers were examined using X-ray diffractometer (XRD) and scanning electron microscope (SEM). XRD results showed that WCCo-Mo composite coatings were mainly composed of WC, W2C, Co3W3C, Mo2C, MoO2, Mo and Co phases. The average hardness of the coatings increased with increasing Mo content