MBMark. D. Bird

Mark. D. Bird

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mark. D. Bird has a total of 96 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Control of turn-to-turn contact resistivity in no-insulation REBCO coils

    by Jun Lu, Kwangmin Kim, Iain Dixon, Justin Deterding, Emsley Marks, Brent Jarvis, Denis Markiewicz, Hongyu Bai, Mark Bird

    No-insulation (NI) REBCO magnets with optimized contact resistivity feature short ramp times and low ramp losses while maintaining the advantages of NI coils with high engineering current density and tolerance for defects in the REBCO conductor. Control of the turn-to-turn contact resistivity ( ρ c ) is key to NI technology. ρ c must be sufficiently high to prevent a large transient current, which could result in high mechanical stress during magnet quenches. Meanwhile it must be lower than the quench propagation limit to avoid conductor burn-out during a quench. Therefore, it is critical to control ρ c within a suitable range of values which is usually coil specific. Previously, we discovered that ρ c between two REBCO tapes with a stainless steel interlayer decreases dramatically with contact pressure cycling by up to three orders of magnitude. This drastic change makes it impossible to design a suitable ρ c value for a stainless steel co-wound NI magnet. In this work, we first present methods for mitigating ρ c pressure cycling sensitivity. We found that by adding conductive fillers, such as conductive paste or epoxy, the ρ c load cycling sensitivity is largely mitigated. For dry-wound coils, ρ c load cycling sensitivity is mitigated by coating REBCO tape with a layer of 2–3 µ m of PbSn solder. In addition, ρ c can be controlled by oxidizing the stainless steel co-wind tape by heating stainless steel tapes at different temperatures in air. Using above methods, short sample tests showed that ρ c was controlled to prescribed values of 1000 and 5000 µ Ω-cm 2 and was not sensitive to contact pressure cycling up to 30 000 cycles at 4.2 K. The new ρ c control method was applied to a 6 double-pancake test coil which was tested at 4.2 K. The ρ c in this test coil was comparable with the short sample results. This demonstrated the ability of this new method to control ρ c in large coils. Moreover, we propose a method of measuring coil’s ρ c by the decay time of coil’s inductive voltage.


  • Screening Current-Induced Stress and Strain Analysis Considering a Non-uniform Thickness Profile of REBCO Tapes

    by Yu Suetomi, Shannon Griffin, Hongyu Bai, Mark Bird, Dmytro Abraimov, Adonay Almanza-Enriquez, Noah Gavin, Jun Lu, Iain R. Dixon

    Winding compressibility (WCP) is a significant reduction in the effective radial Young's modulus of REBCO pancake coils compared with the sum of the various macroscopic components, due to microscopic asperities on the tape surface and/or a non-uniform tape profile. For pancakes that are impregnated either not at all or with something soft like paraffin, this has a substantial impact on the screening current induced stress (SCIS) calculation. In this study, we propose a modeling technique called Penalty Function with Gap Offset (PGO) that incorporates non-uniform tape profiles as a gap offset distribution within contact boundaries. We also evaluate the effectiveness of reinforcement options—co-winding (CW), over-banding (OB), and outer ring (OR)— by considering winding compressibility.


  • Some Consequences of Screening Currents in Solenoids Constructed from REBCO Double-Pancakes

    by Peng Xu, Mark D. Bird, Dylan Kolb-Bond, Ernesto Bosque

    It is well known that screening currents are induced in high-temperature superconducting tapes when they are located in a magnetic field that is changing with time. In recent years, the consequences of these screening currents have become better understood in the context of solenoids built from Rare-earth barium copper oxide (REBCO) double pancakes; specifically, the impact that can occur to the magnetic field distribution and the stress distribution. Pursuing this line of research further, a revisit of the 32-T prototype magnet in terms of order of energizing to the quench event has been investigated. A theoretical method and a finite element simulation have also been performed to study the stress/strain distribution, enthalpy margin, and ac losses affecting the quench of the superconducting solenoids. The analytical derivations of the hoop strain presented in this article are based solely on screening currents, excluding the general radial expansion caused by the transport currents.


  • Open Access

    Superconducting magnet technology for the outer coils of resistive-superconducting hybrid magnets

    by Mark D Bird

    The world’s highest-field dc magnets have, for more than 50 years, consisted of a combination of resistive and superconducting (SC) coils that we refer to as a ‘hybrid’. These magnets use SC technology for the outer coils, where the magnetic field is moderate, and resistive-magnet technology for the inner coils, where the field is highest. In such a configuration, higher fields have been attained than was possible with purely SC magnet technology, and lower lifecycle costs are attained than with a purely resistive magnet. The peak field available has been 45 T for over 20 years in Tallahassee, Florida, USA. There is presently a ‘revolution’ underway in hybrid magnet development. A second 45 T hybrid was completed in 2022 in Hefei, China that might be upgraded to 48 T in a few years. The high field lab in Grenoble, France is also testing a hybrid magnet intended to reach 43.5 T but which also might be upgraded to 46 T in a few years. In addition, the lab in Nijmegen, The Netherlands is presently assembling a hybrid magnet intended to operate at 46 T. Papers have been presented and published with conceptual designs of hybrid magnets with fields up to 60 T. Given the developments underway, this is an appropriate time to review the history of such systems, with a particular focus on the larger, more expensive part of the magnets: the SC outsert coils. The demands placed on the SC coils of these magnet systems are unique due to their coupling with resistive coils that are operated at very high stress and wear out regularly, resulting in large field transients and fault forces. The evolution of the technology used for the SC coils of these hybrid systems is presented, evolving from ventilated windings to cable-in-conduit to cryogen-free.


  • Comparison Between Results of Quench Simulation and Tests of a 13 T REBCO Coil in a Strong Background Magnetic Field

    by Andrew V. Gavrilin, Ernesto S. Bosque, William S. Marshall, Kwangmin Kim, Dylan J. Kolb-Bond, Peng Xu, Iain R. Dixon, Yu Suetomi, Mark D. Bird, Hongyu Bai

    In the framework of the 40 T all-superconducting magnet project at the National High Magnetic Field laboratory, improvements have been made in a quench model and the quench code that has been constructed to simulate the behavior of a magnet consisting of an HTS inner coil set with an LTS background field. The quench model, initially developed for the NHMFL 32 T magnet project, incorporates additional details of the REBCO conductor on a localized level. These include nonuniform magnetic field distribution across each conductor turn and deformation of the turns due to screening currents which affects the true field angle applied to the conductor's a-b plane. Detailed measurements of the test coil's conductors have also been made to improve the simulations. These include the slope of the a-b plane using X-ray techniques and IC (B, θ, T) of each conductor length using torque magnetometry. The test coil generating a field up to 13 T is an insulated, two-in-hand REBCO coil with twelve modules. Deliberate quench tests were performed with it in self-field and with a 11.4 T background field. The results and discussion of the comparisons are presented.


  • Axions beyond Gen 2

    by Christian Boutan, Gianpaolo Carosi, Leslie J. Rosenberg, Gray Rybka, K. M. Backes, Chelsea Bartram, Masha Baryakhtar, Mark D. Bird, Caterina Braggio, Dmitry Budker, et al.

    The QCD (Quantum ChromoDynamics) axion emerged as one of the best-motivated dark matter candidates. In 2018, the Axion Dark Matter eXperiment (ADMX), one of the U.S. Department of Energy’s “Gen 2” flagship dark-matter projects, demonstrated first sensitivity to the highly plausible “DFSZ” dark matter axion couplings over a small frequency range. We anticipate this development marks the first step in constructing yet more powerful experiments that can explore large swaths of the axion parameter space at high sensitivity and result in a discovery. But, realizing this requires advances in both our understanding of the theory and experiment design. Between 25 January and 27 January 2021, the “Axions Beyond Gen 2 Workshop” was held, where selected members of the community discussed our broad understanding of the QCD axion and charted a course for future experiments having sensitivity and mass reach well beyond the current “Gen 2” experiments. These proceedings are summaries of the topics presented and discussed.


  • Open Access

    A flexible neutron spectrometer concept with a new ultra-high field steady-state vertical-bore magnet

    by B. L. Winn, C. Broholm, M. D. Bird, B. Haberl, G. E. Granroth, J. Katsaras

    The proposed facility explores materials under ultra-high magnetic fields. By combining the power of high fields to tune materials and of neutron scattering to probe the resulting changes down to the atomic scale, this facility will enable transformative progress in the study of quantum materials and is named for the “TITAN” subset of Greek gods to reflect this transformation. TITAN will offer DC magnetic fields up to at least 20 T. Exploiting the record brightness and bandwidth of the Second Target Station at the Spallation Neutron Source, TITAN will probe atomic-scale responses through high efficiency neutron spectroscopy up to 80 meV energy transfer, high resolution diffraction, and small angle neutron scattering. Focusing neutron optics will maximize flux on accurately positioned samples, while radial collimation and optimized shielding and detection strategies will minimize backgrounds.


  • Screening Current Induced Field Changes During De-Energization With Axial Clamping

    by D. Kolb-Bond, M. D. Bird, T. Painter, Sanath K. Ramakrishna, Arneil Reyes

    The Screening Current Induced Field (SCIF) is useful to determine the gross field contribution of screening currents in a superconducting coil, specifically coils wound with large aspect ratio, single filament high temperature superconductors (HTS) such as Rare Earth Barium Copper Oxide (REBCO). Our numerical model accurately predicted the behavior of the SCIF shape and magnitude during energizing to full field but diverged on de-energization. We suggest that axial clamping and its associated consequences at high field are responsible for the difference in the computed SCIF upon de-energization. Simple methods of approximating this effect and comparisons between numerical and measurement results are presented.


  • Computing Strains Due to Screening Currents in REBCO Magnets

    by Dylan J Kolb-Bond, Edgar Berrospe-Juarez, Mark Bird, Iain R. Dixon, Hubertus W. Weijers, Frederic Trillaud, Victor M. R. Zermeno, Francesco Grilli

    Screening currents have long been known to impact the stress state in tape-wound superconducting coils. In recent years the advent of REBCO tape has led to the development of tape-wound coils by a number of organizations. While several groups have been computing screening currents and ac losses in REBCO tape in a variety of applications for several years, little has been published about the stress due to the screening currents. This problem is challenging due to the need to analyze thousands of REBCO turns which are not bonded together. The T-A formulation of Maxwell's equations employing a homogenization technique enables efficient estimation of the current distribution while structural calculations employing contact elements allow conservative estimation of stresses. Computational results are compared with observed degradation in a test coil. Future coil designs that include the effects of screening current strains are proposed


  • Screening Currents and Hysteresis Losses in the REBCO Insert of the 32 T All-Superconducting Magnet Using T-A Homogenous Model

    by Edgar Berrospe-Juarez, Frederic Trillaud, Victor M. R. Zermeno, Francesco Grilli, Hubertus W. Weijers, Mark D. Bird

    The 32 T all-superconducting magnet of the National High Magnetic Field Laboratory (NHMFL) was successfully tested in December 2017 and it is expected to be soon available for users. This all-superconducting magnet, comprised of a high-temperature superconducting (HTS) insert and a low-temperature superconducting (LTS) outsert, is the first superconducting magnet reaching more than 30 T. One of the challenges facing this new magnet technology is the estimation of the screening currents, and the corresponding hysteresis losses in the two HTS coils. These coils are made of more than 20,000 turns of insulated REBCO conductor connected in series. The modelling of such system represents a significant challenge due to the huge computational load imposed by the size of the system. Up to now, only medium size magnets (made of units of thousands of turns/tapes) have been successfully modelled with methods based on the well-known H formulation of the Maxwell's equations. In the present work, a new model based on the T-A formulation and a homogeneous technique is proposed. This new approach greatly reduces the computational load and allows performing real-time simulations of large-scale HTS magnets on personal computers.