Thi-Hong Tran
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thi-Hong Tran has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Luu Anh Tung
Faculty of Mechanical Engineering, Thai Nguyen University of Technology, 3/2 Street, Tich Luong Ward, Thai Nguyen City 24000, Vietnam
6 shared publications - Vu Ngoc Pi
Thai Nguyen University of Technology, Thai nguyen, Vietnam
6 shared publications - Le Xuan Hung
Thai Nguyen University of Technology
4 shared publications - Le Hong Ky
Vinh Long University of Technology Education
3 shared publications - Quoc-Tuan Nguyen
Academic Affairs, Thai Nguyen University, Tan Thinh ward, Thai Nguyen City 24118, Vietnam
3 shared publications - Tran Ngoc Giang
Thai Nguyen University of Technology
3 shared publications
Latest Publications
- 23 September 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 11417-11447
Geometry-aware multi-output learning for interpretable fused deposition modeling configuration
- 23 September 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 11417-11447
Geometry-aware multi-output learning for interpretable fused deposition modeling configuration
- Open Access
Electrical Discharge Machining with SiC Powder-Mixed Dielectric: An Effective Application in the Machining Process of Hardened 90CrSi Steel
As a successful solution applied to electrical discharge machining (EDM), powder-mixed electrical discharge machining (PMEDM) has been proposed as an upgrade of the EDM process. The optimization of the process parameters of PMEDM is essential and pressing. In this study, Taguchi methods and analysis of variance (ANOVA) were used to find the main parameters affecting surface roughness in the EDM process with SiC powder-mixed-dielectric of hardened 90CrSi steel. The PMEDM parameters selected were the powder concentration, the pulse-on-time, the pulse-off-time, the pulse current, and the server voltage. It was found that SiC powder exhibits positive effects on reducing surface roughness. The roughness obtained with the optimum powder concentration of 4 g/L was reduced by 30.02% compared to that when processed by conventional EDM. Furthermore, the pulse-off-time was found to be the most influential factor that gave an important effect on surface roughness followed by the powder concentration. The EDM condition including a powder concentration of 4 g/L, a pulse-on-time of 6 µs, a pulse-off-time of 21 µs, a pulse current of 8 A, and a server voltage of 4 V resulted in the best surface roughness.
Open AccessElectrical Discharge Machining with SiC Powder-Mixed Dielectric: An Effective Application in the Machining Process of Hardened 90CrSi Steel
As a successful solution applied to electrical discharge machining (EDM), powder-mixed electrical discharge machining (PMEDM) has been proposed as an upgrade of the EDM process. The optimization of the process parameters of PMEDM is essential and pressing. In this study, Taguchi methods and analysis of variance (ANOVA) were used to find the main parameters affecting surface roughness in the EDM process with SiC powder-mixed-dielectric of hardened 90CrSi steel. The PMEDM parameters selected were the powder concentration, the pulse-on-time, the pulse-off-time, the pulse current, and the server voltage. It was found that SiC powder exhibits positive effects on reducing surface roughness. The roughness obtained with the optimum powder concentration of 4 g/L was reduced by 30.02% compared to that when processed by conventional EDM. Furthermore, the pulse-off-time was found to be the most influential factor that gave an important effect on surface roughness followed by the powder concentration. The EDM condition including a powder concentration of 4 g/L, a pulse-on-time of 6 µs, a pulse-off-time of 21 µs, a pulse current of 8 A, and a server voltage of 4 V resulted in the best surface roughness.
- Open Access
- 5 June 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (11) , 3920
Optimizing Replaced Nozzle Diameter of Abrasive Blasting Systems Using Experiment Technique Design
The blasting technique has been broadly utilized to prepare new surfaces for painting, engraving, etc., in industry. In fact, the minimization of the cleaning cost system is essential. However, the knowledge of this technique in terms of optimization has been poor so far. The aim of this study is to find the optimum replaced boron carbide nozzle diameter for the abrasive blasting system. The basis of the study is to find the replaced nozzle diameter to minimize the cost of the blasting system. Seven main parameters are adopted for examining their influences on the response and the optimum replaced nozzle diameter. The design of experiment (DOE) technique is utilized by using Minitab@19. The results reveal that the initial nozzle diameter has the strongest impact on the optimum replaced nozzle diameter. Furthermore, the proposed regression model has been found to be entirely insistent to the experiments. The utilization of this model can provide an effective way to simplify the calculation of the optimum initial nozzle diameter for boron carbide.
- 5 June 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (11) , 3920
Open AccessOptimizing Replaced Nozzle Diameter of Abrasive Blasting Systems Using Experiment Technique Design
The blasting technique has been broadly utilized to prepare new surfaces for painting, engraving, etc., in industry. In fact, the minimization of the cleaning cost system is essential. However, the knowledge of this technique in terms of optimization has been poor so far. The aim of this study is to find the optimum replaced boron carbide nozzle diameter for the abrasive blasting system. The basis of the study is to find the replaced nozzle diameter to minimize the cost of the blasting system. Seven main parameters are adopted for examining their influences on the response and the optimum replaced nozzle diameter. The design of experiment (DOE) technique is utilized by using Minitab@19. The results reveal that the initial nozzle diameter has the strongest impact on the optimum replaced nozzle diameter. Furthermore, the proposed regression model has been found to be entirely insistent to the experiments. The utilization of this model can provide an effective way to simplify the calculation of the optimum initial nozzle diameter for boron carbide.
- Open Access
- 30 March 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (7) , 2365
The Influence of Main Design Parameters on the Overall Cost of a Gearbox
This study is aimed at determining optimum partial gear ratios to minimize the cost of a three-stage helical gearbox. In this work, eleven input parameters were investigated to find their influence on the optimum gear ratios of the second and the third stages ( and ). To reach the goal, a simulation experiment was designed and implemented by a cost optimization program. The results revealed that in addition to the input parameters, their interactions also have important effects in which the total ratio gearbox ratio ( ) and the cost of shaft ( ) have the most impact on and responses, respectively. Moreover, the proposed models of the two responses are highly consistent to the experimental results. The proposed regression equations can be applied to solve optimization cost problems.- 30 March 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (7) , 2365
Open AccessThe Influence of Main Design Parameters on the Overall Cost of a Gearbox
This study is aimed at determining optimum partial gear ratios to minimize the cost of a three-stage helical gearbox. In this work, eleven input parameters were investigated to find their influence on the optimum gear ratios of the second and the third stages ( and ). To reach the goal, a simulation experiment was designed and implemented by a cost optimization program. The results revealed that in addition to the input parameters, their interactions also have important effects in which the total ratio gearbox ratio ( ) and the cost of shaft ( ) have the most impact on and responses, respectively. Moreover, the proposed models of the two responses are highly consistent to the experimental results. The proposed regression equations can be applied to solve optimization cost problems. - Open Access
An Efficient Beam Element Based on Quasi-3D Theory for Static Bending Analysis of Functionally Graded Beams
In this paper, a 2-node beam element is developed based on Quasi-3D beam theory and mixed formulation for static bending of functionally graded (FG) beams. The transverse shear strains and stresses of the proposed beam element are parabolic distributions through the thickness of the beam and the transverse shear stresses on the top and bottom surfaces of the beam vanish. The proposed beam element is free of shear-looking without selective or reduced integration. The material properties of the functionally graded beam are assumed to vary according to the power-law index of the volume fraction of the constituents through the thickness of the beam. The numerical results of this study are compared with published results to illustrate the accuracy and convenience rate of the new beam element. The influence of some parametrics on the bending behavior of FGM beams is investigated.
Open AccessAn Efficient Beam Element Based on Quasi-3D Theory for Static Bending Analysis of Functionally Graded Beams
In this paper, a 2-node beam element is developed based on Quasi-3D beam theory and mixed formulation for static bending of functionally graded (FG) beams. The transverse shear strains and stresses of the proposed beam element are parabolic distributions through the thickness of the beam and the transverse shear stresses on the top and bottom surfaces of the beam vanish. The proposed beam element is free of shear-looking without selective or reduced integration. The material properties of the functionally graded beam are assumed to vary according to the power-law index of the volume fraction of the constituents through the thickness of the beam. The numerical results of this study are compared with published results to illustrate the accuracy and convenience rate of the new beam element. The influence of some parametrics on the bending behavior of FGM beams is investigated.
- Open Access
Optimization of Replaced Grinding Wheel Diameter for Surface Grinding Based on a Cost Analysis
Based on a cost analysis, a method of identifying and predicting optimum replaced grinding wheel diameter (De.op) in a surface grinding operation for 9CrSi steel material was developed in this study. The De.op value was determined by minimizing the cost function. An experimental design was set up, and a computational program was developed to perform the experiment in order to calculate the De.op value. Furthermore, the impact of the grinding process parameters such as the initial grinding wheel diameter, the grinding wheel width, the total dressing depth, the Rockwell hardness of the workpiece, the radial grinding wheel wear per dress, and the wheel life on the De.op value were investigated. Moreover, the impacts of the cost components such as the machine tool hourly rate and the grinding wheel cost on the De.op value were given. Based on that, a mathematical model was proposed to determine the De.op value. The predicted De.op value was also verified by an experiment. The obtained result shows that the difference between the experimental De.op value and the predicted De.op value is within 1.7%, indicating that the mathematical model proposed in the study is reliable.
Open AccessOptimization of Replaced Grinding Wheel Diameter for Surface Grinding Based on a Cost Analysis
Based on a cost analysis, a method of identifying and predicting optimum replaced grinding wheel diameter (De.op) in a surface grinding operation for 9CrSi steel material was developed in this study. The De.op value was determined by minimizing the cost function. An experimental design was set up, and a computational program was developed to perform the experiment in order to calculate the De.op value. Furthermore, the impact of the grinding process parameters such as the initial grinding wheel diameter, the grinding wheel width, the total dressing depth, the Rockwell hardness of the workpiece, the radial grinding wheel wear per dress, and the wheel life on the De.op value were investigated. Moreover, the impacts of the cost components such as the machine tool hourly rate and the grinding wheel cost on the De.op value were given. Based on that, a mathematical model was proposed to determine the De.op value. The predicted De.op value was also verified by an experiment. The obtained result shows that the difference between the experimental De.op value and the predicted De.op value is within 1.7%, indicating that the mathematical model proposed in the study is reliable.
- Open Access
- 31 March 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (7) , 1363
Optimization of Replaced Grinding Wheel Diameter for Minimum Grinding Cost in Internal Grinding
This paper shows an optimization study on calculating the optimum replaced wheel diameter in internal grinding of stainless steel. In this work, the effects of the input factors, including the initial diameter, the grinding wheel width, the ratio between the length and the diameter of the work-pieces, the dressing depth of cut, the wheel life and the radial grinding wheel wear per dress on the optimum replaced grinding wheel diameter were considered. Also, the effects of cost components, including the cost of the grinding machine and the wheel cost were examined. Moreover, to estimate the influences of these parameters on the optimum replaced diameter, a simulation experiment was given and conducted by programming. From the results of the study, a regression equation was proposed to calculate the optimum replaced diameter.
- 31 March 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (7) , 1363
Open AccessOptimization of Replaced Grinding Wheel Diameter for Minimum Grinding Cost in Internal Grinding
This paper shows an optimization study on calculating the optimum replaced wheel diameter in internal grinding of stainless steel. In this work, the effects of the input factors, including the initial diameter, the grinding wheel width, the ratio between the length and the diameter of the work-pieces, the dressing depth of cut, the wheel life and the radial grinding wheel wear per dress on the optimum replaced grinding wheel diameter were considered. Also, the effects of cost components, including the cost of the grinding machine and the wheel cost were examined. Moreover, to estimate the influences of these parameters on the optimum replaced diameter, a simulation experiment was given and conducted by programming. From the results of the study, a regression equation was proposed to calculate the optimum replaced diameter.
- Open Access
- 6 March 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (5) , 957
Optimization of Grinding Parameters for Minimum Grinding Time When Grinding Tablet Punches by CBN Wheel on CNC Milling Machine
Cutting regime parameters play an important role in determining the efficiency of the grinding process and the quality of the ground parts. In this study, the influences of the cutting parameters, including the cutting depth (ae), the feed rate (Fe) and the wheel speed (RPM) on the grinding time when grinding tablet shape punches by a cubic boron nitride (CBN) wheel on a CNC (Computerized Numerical Control) milling machine are investigated. The Taguchi technique based on orthogonal array and analysis of variance (ANOVA) was then applied to design the number of experiments and evaluate the influence of cutting depth, feed rate and wheel speed on the grinding time. The results show that among the three cutting parameters, the most influential parameter on the grinding time is the cutting depth. The second influential parameter on the grinding time is the feed rate. The least influential parameter on grinding time is the wheel speed. In addition, the optimal condition of cutting parameters obtained for grinding tablet shape punches by cubic boron nitride wheels on a CNC milling machine are a cutting depth of 0.03 mm, wheel speed of 5000 rpm and feed rate of 3500 mm/min. This optimum cutting parameters ensure the least grinding time.
- 6 March 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (5) , 957
Open AccessOptimization of Grinding Parameters for Minimum Grinding Time When Grinding Tablet Punches by CBN Wheel on CNC Milling Machine
Cutting regime parameters play an important role in determining the efficiency of the grinding process and the quality of the ground parts. In this study, the influences of the cutting parameters, including the cutting depth (ae), the feed rate (Fe) and the wheel speed (RPM) on the grinding time when grinding tablet shape punches by a cubic boron nitride (CBN) wheel on a CNC (Computerized Numerical Control) milling machine are investigated. The Taguchi technique based on orthogonal array and analysis of variance (ANOVA) was then applied to design the number of experiments and evaluate the influence of cutting depth, feed rate and wheel speed on the grinding time. The results show that among the three cutting parameters, the most influential parameter on the grinding time is the cutting depth. The second influential parameter on the grinding time is the feed rate. The least influential parameter on grinding time is the wheel speed. In addition, the optimal condition of cutting parameters obtained for grinding tablet shape punches by cubic boron nitride wheels on a CNC milling machine are a cutting depth of 0.03 mm, wheel speed of 5000 rpm and feed rate of 3500 mm/min. This optimum cutting parameters ensure the least grinding time.
- Open Access
A New Beam Model for Simulation of the Mechanical Behaviour of Variable Thickness Functionally Graded Material Beams Based on Modified First Order Shear Deformation Theory
There are many beam models to simulate the variable thickness functionally graded material (FGM) beam, each model has advantages and disadvantages in computer aided engineering of the mechanical behavior of this beam. In this work, a new model of beam is presented to study the mechanical static bending, free vibration, and buckling behavior of the variable thickness functionally graded material beams. The formulations are based on modified first order shear deformation theory and interpolating polynomials. This new beam model is free of shear-locking for both thick and thin beams, is easy to apply in computation, and has efficiency in simulating the variable thickness beams. The effects of some parameters, such as the power-law material index, degree of non-uniformity index, and the length-to-height ratio, on the mechanical behavior of the variable thickness FGM beam are considered.
Open AccessA New Beam Model for Simulation of the Mechanical Behaviour of Variable Thickness Functionally Graded Material Beams Based on Modified First Order Shear Deformation Theory
There are many beam models to simulate the variable thickness functionally graded material (FGM) beam, each model has advantages and disadvantages in computer aided engineering of the mechanical behavior of this beam. In this work, a new model of beam is presented to study the mechanical static bending, free vibration, and buckling behavior of the variable thickness functionally graded material beams. The formulations are based on modified first order shear deformation theory and interpolating polynomials. This new beam model is free of shear-locking for both thick and thin beams, is easy to apply in computation, and has efficiency in simulating the variable thickness beams. The effects of some parameters, such as the power-law material index, degree of non-uniformity index, and the length-to-height ratio, on the mechanical behavior of the variable thickness FGM beam are considered.