Michael Sawannia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Michael Sawannia has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Christian Hagenlocher
Institut für Strahlwerkzeuge (IFSW), Universität Stuttgart, Stuttgart, Germany
2 shared publicationsThomas Graf
Institut für Strahlwerkzeuge (IFSW), Universität Stuttgart, Stuttgart, Germany
2 shared publications- Daniel Johannes Förster
Munich University of Applied Sciences HM
1 shared publication - Hans-Albert Eckel
German Aerospace Center (DLR), Institute of Technical Physics, Pfaffenwaldring 38-40, 70569 Stuttgart, Germany
1 shared publication - Jan Pastow
German Aerospace Center (DLR), Institute of Technical Physics, Pfaffenwaldring 38-40, 70569 Stuttgart, Germany
1 shared publication John Powell
Institut für Strahlwerkzeuge (IFSW), Universität Stuttgart, Stuttgart, Germany
1 shared publication
Latest Publications
- Open Access
- 28 November 2025
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 13 (1) , 45-62
Laser Cutting; Experimental Measurement of Fluctuations in Cut Front Temperature and Morphology
Simulations of laser cutting need experimental measurements of the cutting front geometry and its temperature for validation purposes. A combined polarization goniometer and quotient pyrometer was used to measure these values for a cut in 10 mm stainless steel using a framerate of 75 kHz and a spatial resolution of 36 μm. For the first time, synchronized geometric and temperature measurements are given for a laser cutting front. These measurements show that, for 1 μm wavelength laser cutting of stainless steel, one of the main mechanisms of thermal and material flow involves the movement of hot ‘humps’ of liquid down the cutting front. These mobile humps experience an enhanced absorption of laser radiation on their upper surface and a reduced absorbed power density on their lower part, and may even cast a shadow on the cut front immediately below them. In this work, these phenomena resulted in local temperature fluctuations of 800 K, including temperature drops to 200 K below the melting temperature for durations of up to approximately 200 µs.
- 28 November 2025
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 13 (1) , 45-62
Open AccessLaser Cutting; Experimental Measurement of Fluctuations in Cut Front Temperature and Morphology
Simulations of laser cutting need experimental measurements of the cutting front geometry and its temperature for validation purposes. A combined polarization goniometer and quotient pyrometer was used to measure these values for a cut in 10 mm stainless steel using a framerate of 75 kHz and a spatial resolution of 36 μm. For the first time, synchronized geometric and temperature measurements are given for a laser cutting front. These measurements show that, for 1 μm wavelength laser cutting of stainless steel, one of the main mechanisms of thermal and material flow involves the movement of hot ‘humps’ of liquid down the cutting front. These mobile humps experience an enhanced absorption of laser radiation on their upper surface and a reduced absorbed power density on their lower part, and may even cast a shadow on the cut front immediately below them. In this work, these phenomena resulted in local temperature fluctuations of 800 K, including temperature drops to 200 K below the melting temperature for durations of up to approximately 200 µs.
- Open Access
- 5 July 2024
- Published by Springer Nature in Applied Physics B
- Vol. 130 (8)
High-speed single-frame polarimeter for thermal radiation to measure the 3D geometry of hot metal surfaces
The 3D geometry of the interaction zone in laser material processing is of major importance as it defines the absorption of the laser beam and may influence the hydrodynamics of the process. With the aim of measuring this geometry, which typically changes with frequencies in the order of 10 kHz, a single-frame polarimeter with acquisition rates of up to 75 kHz is presented in this work. It simultaneously records four images of the thermal process emission, through four linear polarizers with different orientations. The formulae required for the reconstruction of the 3D geometry from these images are derived and validated on an example of a heated steel sphere. The reconstructed geometry was found to be in good agreement with the examined sphere. An experimental example is also given of the application of this technology to geometry measurement of a highly dynamic laser cutting front at a framerate of 75 kHz.
- 5 July 2024
- Published by Springer Nature in Applied Physics B
- Vol. 130 (8)
Open AccessHigh-speed single-frame polarimeter for thermal radiation to measure the 3D geometry of hot metal surfaces
The 3D geometry of the interaction zone in laser material processing is of major importance as it defines the absorption of the laser beam and may influence the hydrodynamics of the process. With the aim of measuring this geometry, which typically changes with frequencies in the order of 10 kHz, a single-frame polarimeter with acquisition rates of up to 75 kHz is presented in this work. It simultaneously records four images of the thermal process emission, through four linear polarizers with different orientations. The formulae required for the reconstruction of the 3D geometry from these images are derived and validated on an example of a heated steel sphere. The reconstructed geometry was found to be in good agreement with the examined sphere. An experimental example is also given of the application of this technology to geometry measurement of a highly dynamic laser cutting front at a framerate of 75 kHz.
- Open Access
Power Spectral Density Evaluation of Laser Milled Surfaces
Ablating surfaces with a pulsed laser system in milling processes often leads to surface changes depending on the milling depth. Especially if a constant surface roughness and evenness is essential to the process, structural degradation may advance until the process fails. The process investigated is the generation of precise thrust by laser ablation. Here, it is essential to predict or rather control the evolution of the surfaces roughness. Laser ablative milling with a short pulse laser system in vacuum (≈1 Pa) were performed over depths of several 10 µm documenting the evolution of surface roughness and unevenness with a white light interference microscope. Power spectral density analysis of the generated surface data reveals a strong influence of the crystalline structure of the solid. Furthermore, it was possible to demonstrate that this effect could be suppressed for gold.
Open AccessPower Spectral Density Evaluation of Laser Milled Surfaces
Ablating surfaces with a pulsed laser system in milling processes often leads to surface changes depending on the milling depth. Especially if a constant surface roughness and evenness is essential to the process, structural degradation may advance until the process fails. The process investigated is the generation of precise thrust by laser ablation. Here, it is essential to predict or rather control the evolution of the surfaces roughness. Laser ablative milling with a short pulse laser system in vacuum (≈1 Pa) were performed over depths of several 10 µm documenting the evolution of surface roughness and unevenness with a white light interference microscope. Power spectral density analysis of the generated surface data reveals a strong influence of the crystalline structure of the solid. Furthermore, it was possible to demonstrate that this effect could be suppressed for gold.