TWTao Wang

Tao Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Tao Wang has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Oxidation behavior of Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2C-Mx C (M = Ti, Zr, Hf, Nb, Ta) composite ceramic at high temperature

    by Shuai Xu, Tao Wang, Xingang Wang, Lu Wu, Zhongqiang Fang, Fangfang Ge, Xuan Meng, Qing Liao, Jinchun Wei, Bingsheng Li

    Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2C–Mx C composite ceramic was prepared by hot press sintering, with the Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2C high-entropy carbide as the main phase. Secondary phase Mx C (M = Ti, Zr, Hf, Nb, Ta) was found to be distributed relatively uniform in the composite ceramic. The oxidation behavior of the ceramic was examined after exposure to 923 K and 1173 K. Morphology of the surface and cross sections of all oxidation samples were observed. The characteristics of the oxidation behavior of the high-entropy carbide and the secondary phase Mx C were compared and analyzed. The secondary phases (such as Ti-rich carbide or Hf-rich carbide) in the material were seriously oxidized at 923 K and 1173 K, which reflects the superior oxidation performance of the high-entropy carbide. The nano high-entropy oxides with Ti, Zr, Hf, Nb, Ta, and O elements were discovered by oxidation of the composite ceramic. This research will help deepen the understanding of the oxidation mechanism of high-entropy carbide and composite ceramic.


  • Hydrogen isotopic replacement and microstructure evolution in zirconium deuteride implanted by 150 keV protons*

    by Man Zhao, Mingxu Zhang, Tao Wang, Jiangtao Zhao, Pan Dong, Zhen Yang, Tieshan Wang

    Zirconium tritiated (ZrTx) is an alternative target material for Deuteron–Triton (D-T) reaction neutron generator. The isotopic replacement and microstructure evolution induced by hydrogen isotope implantation could significantly affect the performance of the target film. In this work, the zirconium deuteride film deposited on Mo/Si substrate was implanted by 150 keV protons with fluence from 1×1016 to 1×1018 protons/cm2. After implantation, the depth profiles of retained hydrogen (H) and Deuterium (D) in these target films were analyzed by Elastic Recoil Detection Analysis (ERDA), Time of Flight-Secondary Ion Mass Spectrometry (ToF-SIMS). Additionally, the microstructure evolution was also observed by X-Ray Diffraction (XRD) and Scanning Electron Microscope (SEM). The D concentration in the ZrDx film decreases versus the proton implantation fluence. An analytical model is proposed to describe hydrogen isotopic trapping and exchange as functions of incident protons fluence. Additionally, the XRD analysis reveals no new phase was formed after proton implantation. Furthermore, circular flakings are observed on the ZrDx surface from SEM images at fluence up to 1×1018 protons/cm2, and this surface morphology is considered to associate with the hydrogen atoms congregation in Mo/Si boundary.

  • Open Access

    Lattice Defects and Exfoliation Efficiency of 6H-SiC via H2+ Implantation at Elevated Temperature

    by Tao Wang, Zhen Yang, Bingsheng Li, Shuai Xu, Qing Liao, Fangfang Ge, Tongmin Zhang, Jun Li

    Silicon carbide (SiC) is an important material used in semiconductor industries and nuclear power plants. SiC wafer implanted with H ions can be cleaved inside the damaged layer after annealing, in order to facilitate the transfer of a thin SiC slice to a handling wafer. This process is known as “ion-cut” or “Smart-Cut”. It is worth investigating the exfoliation efficiency and residual lattice defects in H-implanted SiC before and after annealing. In the present paper, lattice damage in the 6H-SiC implanted by H2+ to a fluence of 5 × 1016 H2+/cm2 at 450 and 900 °C was investigated by a combination of Raman spectroscopy and transmission electron microscopy. Different levels of damage caused by dynamic annealing were observed by Raman spectroscopy and transmission electron microscopy in the as-implanted sample. Atomic force microscopy and scanning white-light interferometry were used to observe the sample surface morphology. Surface blisters and exfoliations were observed in the sample implanted at 450 °C and then annealed at 1100 °C for 15 min, whereas surface blisters and exfoliation occurred in the sample implanted at 900 °C without further thermal treatment. This finding can be attributed to the increase in the internal pressure of platelets during high temperature implantation. The exfoliation efficiency, location, and roughness after exfoliation were investigated and possible reasons were discussed. This work provides a basis for further understanding and improving the high-efficiency “ion-cut” technology.


  • Open Access

    Diffusion and distribution of deuterium in scandium deuteride thin films under irradiation of deuterium ion beam

    by Tao Wang, Jidong Long, Shiwei Wang, Zhen Yang, Jie Li, Gang Huang, Linwen Zhang, Allen Jian Yang, Xiao Renshaw Wang

    Scandium deuteride (ScDx) thin films, as an alternative target for deuterium-deuterium (D-D) reaction, are a very important candidate for detection and diagnostic applications. Albeit with their superior thermal stability, the ignorance of the stability of ScDx under irradiation of deuterium ion beam hinders the realization of their full potential. In this report, we characterize ScDx thin films with scanning electron microscopy (SEM) and X-ray diffraction (XRD), Rutherford backscattering spectroscopy (RBS) and elastic recoil detection analysis (ERDA). We found with increased implantation of deuterium ions, accumulation and diffusion of deuterium are enhanced. Surprisingly, the concentration of deuterium restored to the value before implantation even at room temperature, revealing a self-healing process which is of great importance for the long-term operation of neutron generator.


  • Electrical shielding box measurement of the negative hydrogen beam from Penning ion gauge ion source

    by T. Wang, Z. Yang, P. Dong, J. D. Long, X. Z. He, X. Wang, K. Z. Zhang, L. W. Zhang

    The cold-cathode Penning ion gauge (PIG) type ion source has been used for generation of negative hydrogen (H−) ions as the internal ion source of a compact cyclotron. A novel method called electrical shielding box dc beam measurement is described in this paper, and the beam intensity was measured under dc extraction inside an electrical shielding box. The results of the trajectory simulation and dc H− beam extraction measurement were presented. The effect of gas flow rate, magnetic field strength, arc current, and extraction voltage were also discussed. In conclusion, the dc H− beam current of about 4 mA from the PIG ion source with the puller voltage of 40 kV and arc current of 1.31 A was extrapolated from the measurement at low extraction dc voltages.