A. Vinoth Jebaraj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
A. Vinoth Jebaraj has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
C R Deepak
National Institute of Ocean Technology, Chennai – 600100, Tamil Nadu, India
1 shared publicationC.R. Deepak
National Institute of Ocean Technology, Chennai, India
1 shared publicationK.M. Aravindan
1 shared publicationK.V.V. Aditya
Department of Mining Engineering, College of Engineering Guindy, Anna University, India
1 shared publicationKumar M.D. Barath
1 shared publicationKumar T. Sampath
1 shared publication
Latest Publications
- Open Access
- 1 January 2021
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 49 (1) , 87-94
Effect of post-fabrication treatments on surface residual stresses of additive manufactured stainless steel 316L
In this work, an investigation was made to analyze the surface residual stresses on additive manufactured stainless steel AISI 316L in as-built and post-treated conditions. Direct metal laser sintering was used to fabricate the metal blocks. X-ray residual stress analysis on the as-fabricated surface revealed the presence of an inhomogeneous and irregular distribution of residual stresses in the as-built condition ranging from - 30 MPa to 111 MPa. It was mainly due to the localized laser heat source that caused variations in stresses at a lattice level. Heat treatment was performed for providing relief to the residual stress from the as-built condition showed significant relief of residual stress, which was lesser than 50% compared to as-built condition. Beneficial compressive residual stress induced by shot peening and lapping resulted in high magnitude compressive stresses on the surface. Also, homogeneous distribution of residual stress was found on the peened and lapped surface layer with an average of - 531 MPa and - 554 MPa, respectively.
- 1 January 2021
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 49 (1) , 87-94
Open AccessEffect of post-fabrication treatments on surface residual stresses of additive manufactured stainless steel 316L
In this work, an investigation was made to analyze the surface residual stresses on additive manufactured stainless steel AISI 316L in as-built and post-treated conditions. Direct metal laser sintering was used to fabricate the metal blocks. X-ray residual stress analysis on the as-fabricated surface revealed the presence of an inhomogeneous and irregular distribution of residual stresses in the as-built condition ranging from - 30 MPa to 111 MPa. It was mainly due to the localized laser heat source that caused variations in stresses at a lattice level. Heat treatment was performed for providing relief to the residual stress from the as-built condition showed significant relief of residual stress, which was lesser than 50% compared to as-built condition. Beneficial compressive residual stress induced by shot peening and lapping resulted in high magnitude compressive stresses on the surface. Also, homogeneous distribution of residual stress was found on the peened and lapped surface layer with an average of - 531 MPa and - 554 MPa, respectively.
- Open Access
- 1 November 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 263 (6) , 062057
Influence of shot peening on surface quality of austenitic and duplex stainless steel
In the present investigation, an attempt has been made to enhance the surface quality of austenitic stainless steel 316L and duplex stainless steel 2205 through shot peening process. The study mainly focuses the surface morphology, microstructural changes, surface roughness and microhardness of the peened layers. Metallography analysis was carried out and compared with the unpeened surface characteristics. As result of peening process, surface recrystallization was achieved on the layers of the peened samples. It was found that shot peening plays significant role in enhancing the surface properties of 316L and 2205. Particularly it has greater influence on the work hardening of austenitic stainless steel than the duplex stainless steel due to its more ductility nature under the investigated shot peening parameters. The findings of the present study will be useful with regard to the enhancement of surface texture achieved through peening.
- 1 November 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 263 (6) , 062057
Open AccessInfluence of shot peening on surface quality of austenitic and duplex stainless steel
In the present investigation, an attempt has been made to enhance the surface quality of austenitic stainless steel 316L and duplex stainless steel 2205 through shot peening process. The study mainly focuses the surface morphology, microstructural changes, surface roughness and microhardness of the peened layers. Metallography analysis was carried out and compared with the unpeened surface characteristics. As result of peening process, surface recrystallization was achieved on the layers of the peened samples. It was found that shot peening plays significant role in enhancing the surface properties of 316L and 2205. Particularly it has greater influence on the work hardening of austenitic stainless steel than the duplex stainless steel due to its more ductility nature under the investigated shot peening parameters. The findings of the present study will be useful with regard to the enhancement of surface texture achieved through peening.
- Top Cited PapersOpen Access
- 1 May 2017
- Published by Elsevier in Journal of Advanced Research
- Vol. 8 (3) , 183-199
Weldability, machinability and surfacing of commercial duplex stainless steel AISI2205 for marine applications – A recent review
- 1 May 2017
- Published by Elsevier in Journal of Advanced Research
- Vol. 8 (3) , 183-199
Top Cited PapersOpen AccessWeldability, machinability and surfacing of commercial duplex stainless steel AISI2205 for marine applications – A recent review