Xin Ding
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xin Ding has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Chenggang Yan
College of Electronic and Information Engineering, Nanjing University of Aeronautics and Astronautics
2 shared publications- Chirn Chye Boon
Nanyang Technological University
2 shared publications - Jianhui Wu
School of Integrated Circuits, Southeast University, Nanjing, China
2 shared publications - Yangtao Dong
VIRTUS, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
2 shared publications - Ao Zhou
CICS, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
1 shared publication Chao Chen
National ASIC research center, Southeast University, Nanjing, 210096 and also with the Jiangsu Key Laboratory of sensor network technology, Nanjing, China
1 shared publication
Latest Publications
- Open Access
- 29 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 137241-137248
A Low-Power Quadrature LO Generator With Mutual Power-Supply Rejection Technique
This paper presents a supply-insensitive low-power quadrature local oscillation (LO) generator based on the current-reused voltage-controlled oscillator (VCO) and divide-by-two frequency divider (FD). By utilizing the mutual power-supply rejection (M-PSR) technique, a voltage regulator is embedded into the FD to provide a supply-insensitive voltage for VCO. Meanwhile, the feedback loop provides a supply-insensitive current and time constant compensation for FD. The M-PSR technique does not require extra voltage headroom, thus the proposed quadrature LO generator can work under the supply of 0.9 V. A prototype of the proposed quadrature LO generator is implemented in a 28-nm CMOS process. Measurement results indicate that the LO generator achieves a phase noise of −110.5 dBc/Hz@1MHz at the carrier of 5.9 GHz and the power consumption is 1.8 mW. This work has a competitive figure of merit in supply sensitivity or in area (FOM ss or FOM a respectively) among the state-of-the-art works.
- 29 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 137241-137248
Open AccessA Low-Power Quadrature LO Generator With Mutual Power-Supply Rejection Technique
This paper presents a supply-insensitive low-power quadrature local oscillation (LO) generator based on the current-reused voltage-controlled oscillator (VCO) and divide-by-two frequency divider (FD). By utilizing the mutual power-supply rejection (M-PSR) technique, a voltage regulator is embedded into the FD to provide a supply-insensitive voltage for VCO. Meanwhile, the feedback loop provides a supply-insensitive current and time constant compensation for FD. The M-PSR technique does not require extra voltage headroom, thus the proposed quadrature LO generator can work under the supply of 0.9 V. A prototype of the proposed quadrature LO generator is implemented in a 28-nm CMOS process. Measurement results indicate that the LO generator achieves a phase noise of −110.5 dBc/Hz@1MHz at the carrier of 5.9 GHz and the power consumption is 1.8 mW. This work has a competitive figure of merit in supply sensitivity or in area (FOM ss or FOM a respectively) among the state-of-the-art works.
- 14 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 29 (7) , 1480-1484
A Bidirectional Nonlinearly Coupled QVCO With Passive Phase Interpolation for Multiphase Signals Generation
This brief presents a bidirectional nonlinearly coupled quadrature voltage-controlled oscillator (BNC-QVCO) incorporating passive phase interpolation for the generation of multiphase signals. In addition, to generate multiphase signals, the proposed bidirectional nonlinearly coupling network improves the phase noise performance of the QVCO by producing approximate-in-phase injection-coupling currents into the LC tank. Moreover, to balance the amplitude of eight-phase signals, an additional passive amplitude division circuit is implemented with capacitor banks for calibration. For verification, a BNC-QVCO incorporating passive phase interpolation is implemented in a 40-nm CMOS technology with a core area of 0.13 mm 2 . The measured multiphase signals achieve a phase noise of -116.57 dBc/Hz at 1-MHz offset from 4.32 GHz. The power consumption without buffers is 10.2 mW under 1-V supply voltage and a 20% frequency tuning range from 4 to 4.8 GHz is achieved with the implemented digitally controlled capacitor banks.
- 14 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 29 (7) , 1480-1484
A Bidirectional Nonlinearly Coupled QVCO With Passive Phase Interpolation for Multiphase Signals Generation
This brief presents a bidirectional nonlinearly coupled quadrature voltage-controlled oscillator (BNC-QVCO) incorporating passive phase interpolation for the generation of multiphase signals. In addition, to generate multiphase signals, the proposed bidirectional nonlinearly coupling network improves the phase noise performance of the QVCO by producing approximate-in-phase injection-coupling currents into the LC tank. Moreover, to balance the amplitude of eight-phase signals, an additional passive amplitude division circuit is implemented with capacitor banks for calibration. For verification, a BNC-QVCO incorporating passive phase interpolation is implemented in a 40-nm CMOS technology with a core area of 0.13 mm 2 . The measured multiphase signals achieve a phase noise of -116.57 dBc/Hz at 1-MHz offset from 4.32 GHz. The power consumption without buffers is 10.2 mW under 1-V supply voltage and a 20% frequency tuning range from 4 to 4.8 GHz is achieved with the implemented digitally controlled capacitor banks.
- 18 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (6) , 1783-1787
Background Calibration for Bit Weights in Pipelined ADCs Using Adaptive Dither Windows
This brief proposes adaptive dither windows to calibrate bit weights in pipelined analog-to-digital converters (ADCs). It exploits the comparator meta-stability nature to construct dither windows, which avoids doubling the number of the comparators. The dither window size as defined by the sub-ADC comparator metastability region is tightly controlled and adapted to process-voltage-temperature (PVT) variations by adjusting the digitally controlled delay lines (DCDLs) against a capacitor-ratio reference. Besides, it cancels the voltage swing increment due to the dither windows, which relieves the design of the residue amplifier and saves the over-range margin of the stage. The proposed calibration technique is demonstrated by using a 12-bit pipelined ADC in a 40 nm CMOS process, and simulation results show that the window size is adjusted adaptively under PVT corners while the voltage swing increment is cancelled. The spurious-free-dynamic-range (SFDR) and the signal-to-noise-and-distortion-ratio (SNDR) are improved from 61.8 dB and 53 dB to 92 dB and 73.6 dB, respectively.
- 18 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 68 (6) , 1783-1787
Background Calibration for Bit Weights in Pipelined ADCs Using Adaptive Dither Windows
This brief proposes adaptive dither windows to calibrate bit weights in pipelined analog-to-digital converters (ADCs). It exploits the comparator meta-stability nature to construct dither windows, which avoids doubling the number of the comparators. The dither window size as defined by the sub-ADC comparator metastability region is tightly controlled and adapted to process-voltage-temperature (PVT) variations by adjusting the digitally controlled delay lines (DCDLs) against a capacitor-ratio reference. Besides, it cancels the voltage swing increment due to the dither windows, which relieves the design of the residue amplifier and saves the over-range margin of the stage. The proposed calibration technique is demonstrated by using a 12-bit pipelined ADC in a 40 nm CMOS process, and simulation results show that the window size is adjusted adaptively under PVT corners while the voltage swing increment is cancelled. The spurious-free-dynamic-range (SFDR) and the signal-to-noise-and-distortion-ratio (SNDR) are improved from 61.8 dB and 53 dB to 92 dB and 73.6 dB, respectively.
- 14 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (12) , 2818-2822
A Low-Spur MASH Delta-Sigma Modulator With an Adaptive Length Extension Technique
This brief presents a novel multistage noise-shaping (MASH) delta-sigma modulator that has low spurs for all input values by the proposed adaptive length extension technique. Based on the feedforward structure, the accumulators in the proposed MASH are fully utilized to realize an adaptive feedforward gain to compensate for the sequence length loss due to input. The proposed MASH can extend the output sequence length to the maximum under any input, thus to reduce spurs. Simulation results show that the quantization noise of the proposed MASH is distributed widely with no noticeable spurs. Synthesized with 180nm CMOS technology, the increase in hardware cost of the proposed MASH is slight.
- 14 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (12) , 2818-2822
A Low-Spur MASH Delta-Sigma Modulator With an Adaptive Length Extension Technique
This brief presents a novel multistage noise-shaping (MASH) delta-sigma modulator that has low spurs for all input values by the proposed adaptive length extension technique. Based on the feedforward structure, the accumulators in the proposed MASH are fully utilized to realize an adaptive feedforward gain to compensate for the sequence length loss due to input. The proposed MASH can extend the output sequence length to the maximum under any input, thus to reduce spurs. Simulation results show that the quantization noise of the proposed MASH is distributed widely with no noticeable spurs. Synthesized with 180nm CMOS technology, the increase in hardware cost of the proposed MASH is slight.
- 15 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 66 (2) , 202-206
A Low-Power 0.6-V Quadrature VCO With a Coupling Current Reuse Technique
A novel quadrature voltage-controlled oscillator (QVCO) featuring low power consumption is proposed in this paper. By utilizing the coupling current reuse technique, the coupling current of one core is shared as a source to bias the quadraturequadraturequadraturequadraturequadraturequadraturequadraturequadraturequadraturequadrature coupling device in the other core. Thus, the coupling current consumption is eliminated. Moreover, the injected tank current is reshaped to reduce noise injection and increase efficiency. The coupling current reuse technique allows the proposed QVCO to achieve at least 50% power consumption decreasing compared to previous LC-QVCOs without sacrifices of phase noise and swing. In addition, the quadrature coupling topology is reused as an oscillation detector for dynamic bias control to further decrease power consumption of oscillation cores. A proto-type of the proposed QVCO is designed and fabricated in a 40nm CMOS process. Measurement results indicate that the QVCO achieves a phase noise of -118.6 dBc/Hz@1MHz at the carrier of 1.575 GHz. The power consumption of the proposed QVCO is only 1.32 mW under the supply voltage of 0.6 V.
- 15 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 66 (2) , 202-206
A Low-Power 0.6-V Quadrature VCO With a Coupling Current Reuse Technique
A novel quadrature voltage-controlled oscillator (QVCO) featuring low power consumption is proposed in this paper. By utilizing the coupling current reuse technique, the coupling current of one core is shared as a source to bias the quadraturequadraturequadraturequadraturequadraturequadraturequadraturequadraturequadraturequadrature coupling device in the other core. Thus, the coupling current consumption is eliminated. Moreover, the injected tank current is reshaped to reduce noise injection and increase efficiency. The coupling current reuse technique allows the proposed QVCO to achieve at least 50% power consumption decreasing compared to previous LC-QVCOs without sacrifices of phase noise and swing. In addition, the quadrature coupling topology is reused as an oscillation detector for dynamic bias control to further decrease power consumption of oscillation cores. A proto-type of the proposed QVCO is designed and fabricated in a 40nm CMOS process. Measurement results indicate that the QVCO achieves a phase noise of -118.6 dBc/Hz@1MHz at the carrier of 1.575 GHz. The power consumption of the proposed QVCO is only 1.32 mW under the supply voltage of 0.6 V.