Yangtao Dong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yangtao Dong has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Chirn Chye Boon
Nanyang Technological University
6 shared publications - Zhe Liu
Centre for Integrated Circuits and Systems, School of Electrical and Electronic Engineering, Nanyang Technological University, Jurong West, Singapore
4 shared publications - Chenyang Li
VIRTUS, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
2 shared publications - Kaituo Yang
VIRTUS, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
2 shared publications - Xin Ding
National ASIC Research Center, Southeast University, Nanjing, China
2 shared publications - Yuan Liang
School of Electronics and Communication Engineering, Guangzhou University, Guangzhou, China
2 shared publications
Latest Publications
- 14 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (8) , 3561-3572
A 0.6 V, 1.74 mW, 2.9 dB NF Inductorless Wideband LNA in 28-nm CMOS Exploiting Noise Cancellation and Current Reuse
This paper proposes an inductorless wideband common-gate (CG)-common-source (CS) noise-cancelling (NC) low-noise amplifier (LNA) with current reuse (CR) for ultra-low voltage (ULV) application. In the conventional NC LNA with CR, to reuse the DC current of the auxiliary amplifier, three transistors are stacked in a single branch, leading to a reduced voltage headroom. Moreover, additional inductor and capacitors are required, resulting in a large silicon area. In the proposed work, the DC current of the auxiliary amplifier can be reused without using any inductor. Meanwhile, only two transistors are stacked in a single branch, making it suitable for ULV application. Fabricated in 28 nm CMOS, this work exhibits a voltage gain of 20 dB with a 3-dB bandwidth of 0.2 to 2.85 GHz, a minimum NF of 2.9 dB at 1.7 GHz and an IIP3 of -12.3 dBm at 1 GHz. It consumes 1.74 mW from a 0.6 V supply and occupies a very compact die area of 0.0048 mm $^{2}$ .
- 14 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (8) , 3561-3572
A 0.6 V, 1.74 mW, 2.9 dB NF Inductorless Wideband LNA in 28-nm CMOS Exploiting Noise Cancellation and Current Reuse
This paper proposes an inductorless wideband common-gate (CG)-common-source (CS) noise-cancelling (NC) low-noise amplifier (LNA) with current reuse (CR) for ultra-low voltage (ULV) application. In the conventional NC LNA with CR, to reuse the DC current of the auxiliary amplifier, three transistors are stacked in a single branch, leading to a reduced voltage headroom. Moreover, additional inductor and capacitors are required, resulting in a large silicon area. In the proposed work, the DC current of the auxiliary amplifier can be reused without using any inductor. Meanwhile, only two transistors are stacked in a single branch, making it suitable for ULV application. Fabricated in 28 nm CMOS, this work exhibits a voltage gain of 20 dB with a 3-dB bandwidth of 0.2 to 2.85 GHz, a minimum NF of 2.9 dB at 1.7 GHz and an IIP3 of -12.3 dBm at 1 GHz. It consumes 1.74 mW from a 0.6 V supply and occupies a very compact die area of 0.0048 mm $^{2}$ .
- 22 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (1) , 138-148
A Dual-Path Subsampling PLL With Ring VCO Phase Noise Suppression
This article presents a 2-GHz dual-path subsampling phase-locked loop (SSPLL) with ring voltage-controlled oscillator (VCO) phase noise suppression (PNS). In addition to the conventional subsampling charge pump (SSCP), a high-pass path from the subsampling phase detector (SSPD) to the low-pass filter (LPF) is implemented in the proposed SSPLL. Due to this dual-path architecture, a new in-band zero and pole are introduced into the open-loop transfer function (zero frequency is smaller than the pole frequency), which extends the open-loop unit-gain bandwidth without sacrificing the phase margin. Consequently, the phase noise contribution of the ring VCO is suppressed while the loop stability is ensured. Meanwhile, the phase noise contribution of the high-pass path is negligible compared to the reference and ring VCO’s contribution. Measurement results show that the SSPLL’s closed-loop bandwidth is extended to around 6 MHz with a reference of 20 MHz and the jitter is reduced by 1.34 $\times$ (from 3.52 to 2.63 ps) with a maximum noise suppression of 6.5 dB at the 1.1-MHz offset. The PNS path consumes 0.16 mW and no delay line or calibration is needed, which results in a relatively high FoM $_{\mathrm{PNC}}$ value of 40.5 dB.
- 22 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (1) , 138-148
A Dual-Path Subsampling PLL With Ring VCO Phase Noise Suppression
This article presents a 2-GHz dual-path subsampling phase-locked loop (SSPLL) with ring voltage-controlled oscillator (VCO) phase noise suppression (PNS). In addition to the conventional subsampling charge pump (SSCP), a high-pass path from the subsampling phase detector (SSPD) to the low-pass filter (LPF) is implemented in the proposed SSPLL. Due to this dual-path architecture, a new in-band zero and pole are introduced into the open-loop transfer function (zero frequency is smaller than the pole frequency), which extends the open-loop unit-gain bandwidth without sacrificing the phase margin. Consequently, the phase noise contribution of the ring VCO is suppressed while the loop stability is ensured. Meanwhile, the phase noise contribution of the high-pass path is negligible compared to the reference and ring VCO’s contribution. Measurement results show that the SSPLL’s closed-loop bandwidth is extended to around 6 MHz with a reference of 20 MHz and the jitter is reduced by 1.34 $\times$ (from 3.52 to 2.63 ps) with a maximum noise suppression of 6.5 dB at the 1.1-MHz offset. The PNS path consumes 0.16 mW and no delay line or calibration is needed, which results in a relatively high FoM $_{\mathrm{PNC}}$ value of 40.5 dB.
- Open Access
- 29 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 137241-137248
A Low-Power Quadrature LO Generator With Mutual Power-Supply Rejection Technique
This paper presents a supply-insensitive low-power quadrature local oscillation (LO) generator based on the current-reused voltage-controlled oscillator (VCO) and divide-by-two frequency divider (FD). By utilizing the mutual power-supply rejection (M-PSR) technique, a voltage regulator is embedded into the FD to provide a supply-insensitive voltage for VCO. Meanwhile, the feedback loop provides a supply-insensitive current and time constant compensation for FD. The M-PSR technique does not require extra voltage headroom, thus the proposed quadrature LO generator can work under the supply of 0.9 V. A prototype of the proposed quadrature LO generator is implemented in a 28-nm CMOS process. Measurement results indicate that the LO generator achieves a phase noise of −110.5 dBc/Hz@1MHz at the carrier of 5.9 GHz and the power consumption is 1.8 mW. This work has a competitive figure of merit in supply sensitivity or in area (FOM ss or FOM a respectively) among the state-of-the-art works.
- 29 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 137241-137248
Open AccessA Low-Power Quadrature LO Generator With Mutual Power-Supply Rejection Technique
This paper presents a supply-insensitive low-power quadrature local oscillation (LO) generator based on the current-reused voltage-controlled oscillator (VCO) and divide-by-two frequency divider (FD). By utilizing the mutual power-supply rejection (M-PSR) technique, a voltage regulator is embedded into the FD to provide a supply-insensitive voltage for VCO. Meanwhile, the feedback loop provides a supply-insensitive current and time constant compensation for FD. The M-PSR technique does not require extra voltage headroom, thus the proposed quadrature LO generator can work under the supply of 0.9 V. A prototype of the proposed quadrature LO generator is implemented in a 28-nm CMOS process. Measurement results indicate that the LO generator achieves a phase noise of −110.5 dBc/Hz@1MHz at the carrier of 5.9 GHz and the power consumption is 1.8 mW. This work has a competitive figure of merit in supply sensitivity or in area (FOM ss or FOM a respectively) among the state-of-the-art works.
- 14 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 29 (7) , 1480-1484
A Bidirectional Nonlinearly Coupled QVCO With Passive Phase Interpolation for Multiphase Signals Generation
This brief presents a bidirectional nonlinearly coupled quadrature voltage-controlled oscillator (BNC-QVCO) incorporating passive phase interpolation for the generation of multiphase signals. In addition, to generate multiphase signals, the proposed bidirectional nonlinearly coupling network improves the phase noise performance of the QVCO by producing approximate-in-phase injection-coupling currents into the LC tank. Moreover, to balance the amplitude of eight-phase signals, an additional passive amplitude division circuit is implemented with capacitor banks for calibration. For verification, a BNC-QVCO incorporating passive phase interpolation is implemented in a 40-nm CMOS technology with a core area of 0.13 mm 2 . The measured multiphase signals achieve a phase noise of -116.57 dBc/Hz at 1-MHz offset from 4.32 GHz. The power consumption without buffers is 10.2 mW under 1-V supply voltage and a 20% frequency tuning range from 4 to 4.8 GHz is achieved with the implemented digitally controlled capacitor banks.
- 14 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 29 (7) , 1480-1484
A Bidirectional Nonlinearly Coupled QVCO With Passive Phase Interpolation for Multiphase Signals Generation
This brief presents a bidirectional nonlinearly coupled quadrature voltage-controlled oscillator (BNC-QVCO) incorporating passive phase interpolation for the generation of multiphase signals. In addition, to generate multiphase signals, the proposed bidirectional nonlinearly coupling network improves the phase noise performance of the QVCO by producing approximate-in-phase injection-coupling currents into the LC tank. Moreover, to balance the amplitude of eight-phase signals, an additional passive amplitude division circuit is implemented with capacitor banks for calibration. For verification, a BNC-QVCO incorporating passive phase interpolation is implemented in a 40-nm CMOS technology with a core area of 0.13 mm 2 . The measured multiphase signals achieve a phase noise of -116.57 dBc/Hz at 1-MHz offset from 4.32 GHz. The power consumption without buffers is 10.2 mW under 1-V supply voltage and a 20% frequency tuning range from 4 to 4.8 GHz is achieved with the implemented digitally controlled capacitor banks.
- 1 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Millimetre-Wave and Terahertz Antennas and Directional Coupler Enabled by Wafer-Level Packaging Platform with Interposer
The recent development of wafer-level, low-cost packaging platforms based on the silicon interposer and direct wafer bonding has paved a new way toward high-performance millimeter-wave to terahertz 2.5/3D heterogeneous integration, enabling high-speed wireless communication and chip-to-chip interconnects. Using this emerging technology, several passive components are studied in this paper toward the terahertz applications. One 240 GHz distributed mushroom antenna is designed using interposers to form multiple resonances unit-cell, achieving 7.16 dBi gain with 76% radiation efficiency. A 300 GHz differential patch antenna is designed, delivering 5.6 dBi gain with 88% radiation efficiency. A 60 GHz directional coupler based on interleaving topology is proposed and simulated, showing a 3.3 dB coupling factor with more than 30 GHz bandwidth. These preliminary results reveal a promising solution by using the wafer-to-wafer packaging platform to build high-performance passive building blocks.
- 1 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Millimetre-Wave and Terahertz Antennas and Directional Coupler Enabled by Wafer-Level Packaging Platform with Interposer
The recent development of wafer-level, low-cost packaging platforms based on the silicon interposer and direct wafer bonding has paved a new way toward high-performance millimeter-wave to terahertz 2.5/3D heterogeneous integration, enabling high-speed wireless communication and chip-to-chip interconnects. Using this emerging technology, several passive components are studied in this paper toward the terahertz applications. One 240 GHz distributed mushroom antenna is designed using interposers to form multiple resonances unit-cell, achieving 7.16 dBi gain with 76% radiation efficiency. A 300 GHz differential patch antenna is designed, delivering 5.6 dBi gain with 88% radiation efficiency. A 60 GHz directional coupler based on interleaving topology is proposed and simulated, showing a 3.3 dB coupling factor with more than 30 GHz bandwidth. These preliminary results reveal a promising solution by using the wafer-to-wafer packaging platform to build high-performance passive building blocks.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (6) , 2809-2821
A Wideband dB-Linear Variable-Gain Amplifier With a Compensated Negative Pseudo-Exponential Generation Technique
This article presents a wideband dB-linear variable-gain amplifier (VGA) with a compensated negative pseudo-exponential generation (C-NPEG) technique for high-speed applications. By shifting the concave and the convex function of an original negative pseudo-exponential generator (NPEG), two additional control signals are produced to manipulate two variable-gain Gilbert-cell-based amplifiers, respectively. Cascading these two stages with another variable gain stage controlled by the original NPEG, the multiplication of three different but mutually compensated control signals is realized. As a result, the dB-linear gain range of the overall VGA is extended, and the gain error is suppressed with the proposed C-NPEG technique. To further improve the VGA's gain while maintaining a wide bandwidth, a fixed-gain stage utilizing five common-source amplifiers with RC-degeneration and active feedback is implemented. Fabricated in 40-nm CMOS technology, the core circuit consumes 24.6-mA current (excluding the output buffer) under a power supply of 1.1 V and occupies an active die area of 0.038 mm 2 . The measured gain of the overall VGA varies from -34 to 17 dB, while the dB-linear gain error over the 51-dB gain range is within ±1 dB. Meanwhile, the -3-dB bandwidth is relatively constant from 7 to 8 GHz under different gain settings.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (6) , 2809-2821
A Wideband dB-Linear Variable-Gain Amplifier With a Compensated Negative Pseudo-Exponential Generation Technique
This article presents a wideband dB-linear variable-gain amplifier (VGA) with a compensated negative pseudo-exponential generation (C-NPEG) technique for high-speed applications. By shifting the concave and the convex function of an original negative pseudo-exponential generator (NPEG), two additional control signals are produced to manipulate two variable-gain Gilbert-cell-based amplifiers, respectively. Cascading these two stages with another variable gain stage controlled by the original NPEG, the multiplication of three different but mutually compensated control signals is realized. As a result, the dB-linear gain range of the overall VGA is extended, and the gain error is suppressed with the proposed C-NPEG technique. To further improve the VGA's gain while maintaining a wide bandwidth, a fixed-gain stage utilizing five common-source amplifiers with RC-degeneration and active feedback is implemented. Fabricated in 40-nm CMOS technology, the core circuit consumes 24.6-mA current (excluding the output buffer) under a power supply of 1.1 V and occupies an active die area of 0.038 mm 2 . The measured gain of the overall VGA varies from -34 to 17 dB, while the dB-linear gain error over the 51-dB gain range is within ±1 dB. Meanwhile, the -3-dB bandwidth is relatively constant from 7 to 8 GHz under different gain settings.