Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Muhammad Syahril Mubarok has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Integration of a bidirectional cell in a quasi-Z-source inverter for CMV reduction and pure sinusoidal wave form

    by Mohammad Imron Dwi Prasetyo, Muhammad Syahril Mubarok, Sofyan Muhammad Ilman, Misbahul Munir, Nur Vidia Laksmi B

    With the increasing global commitment to renewable energy sources like photovoltaics (PV), there is a critical need for high-efficiency and high-power-quality converter topologies. Traditional two-stage PV systems are often complex and introduce significant Common Mode Voltage (CMV), leading to issues like leakage currents, high electromagnetic interference, and safety concerns. This paper proposes the Integration of a Bidirectional Cell within a quasi-Z-Source Inverter (BC-qZSI) to achieve CMV Reduction in a single-stage power conversion setup. The BC acts as an active balancing and filtering element rather than solely a boosting stage, ensuring a continuous current mode and actively suppressing the high-frequency CMV components generated by the shoot-through states. The analytical mathematical expression of the proposed topology is derived to confirm its operation, voltage boost capability, and CMV characteristics. Ideal simulation results, performed using PSIM software, validate the derived expressions and demonstrate the effectiveness of the proposed design. The topology achieves a significant reduction in CMV, lowering its amplitude more than 90% compared to the conventional qZSI. Furthermore, the output waveform quality is excellent, yielding a Total Harmonic Distortion (THDv) of 2 %, which complies with the IEEE Std 519-2014 standard for acceptable waveform quality. These results confirm that the integrated BC-qZSI topology effectively mitigates CMV while maintaining high power quality and a single-stage architecture.

  • Open Access

    ELECTRIC BIKES FOR GREEN MOBILITY IMPROVEMENT IN GILI IYANG, MADURA

    by Yoga Uta Nugraha, Muhammad Syahril Mubarok, Retna Apsari

    This community service program is implemented in an island region that has limited access to electricity and fuel. This program is implemented on Gili Iyang Island, Sumenep, Madura. On the island, the only mode of transportation available is motorbikes and three-wheeled motorbikes due to limited and narrow roads. The price of gasoline reaches two to four times the normal price. Based on these conditions, the issue raised in this community service program is the use of electric bicycles for mobility, with the hope that it can also be a means of supporting the main tourist attraction of the island known as "Oxygen Island". This program is training for the community on how to assemble and maintain electric bicycles. The electric bicycles used in this program are designed with compact and flexible advantages, equipped with lithium batteries with a range of up to 30 km. In addition, there is a pedal assist feature to make it easier to pedal when needed, such as when going uphill or crossing sandy roads. For recharging electric bicycles, a solar shelter is provided, which helps save transportation costs. Training is provided through theoretical and practical materials. Participants can directly implement the theory that has been conveyed when practicing assembling bicycles. Based on the results of the pre and post tests, in general, there was an increase of 17-50% in the knowledge and skills of participants related to the assembly and maintenance of electric bicycles. This is a very strong belief that the Gili Iyang community has been able to use and maintain electric bicycles.


  • Open Access

    Cascaded AC-DC parallel boost-flyback converter for power factor correction

    by Nur Vidia Laksmi B., Muhammad Syahril Mubarok, Moh. Zaenal Effendi, Widi Aribowo, Tian-Hua Liu

    A two-stage power factor correction (PFC) topology achieves a higher power factor quality and lower harmonic distortion than a single-stage converter. This paper introduces a two-stage PFC topology using a parallel boost and flyback converter which is employed as a voltage regulator The main boost converter is used for PFC and the other is the active filter circuit. The filter is implemented to improve the quality of phase-current and eliminate the switching loss. Furthermore, a reaction curve of Ziegler-Nichol’s method determines the controller parameter for cascaded PFC converter circuit. Simulated and experimental results are presented to validate the proposed method. The total harmonic distortion (THD) value decreases significantly from 83.35% become 0.98% in the simulation. In addition, experimental results show that the current response has good performances, including less harmonics, higher power factor, and lower THD value compared to without a PFC circuit. The PF increased from 0.43 become 0.96, the THD value decreased from 49.4% become 16.2%, and contains a small number of harmonics. The proposed controller method has better responses than the conventional one, including small steady-state error, fast rise time and settling time. A microcontroller (MCU), type STM32F407VG, produced by STMicroelectronics is used to execute the proposed control in both converters.

  • Open Access

    UTILIZING 3D MAPPING PHOTOGRAMMETRY AND AIRFEEL WEATHER MONITORING FOR SOLAR AND WIND POWER PLANT DEVELOPMENT PLANNING ON GILI IYANG

    by Prisma Megantoro, Retna Apsari, Nayu Nurrohma Hidayah, Feby Ananta Sari, Alyssa Rania Khadijah, Heru Dwi Cahyono, Waldi Abdilah, Yoga Uta Nugraha, Lilik Jamilatul Awalin, Muhammad Syahril Mubarok

    This article discusses community service activities on Gili Iyang Island, Sumenep, Madura, which focus on implementing appropriate technology in sensing the potential of renewable energy sources. Gili Iyang Island itself is an area that actively encourages the use of renewable energy. In this activity, maintenance and monitoring of data on AirFeel are carried out, including device checks and monitoring data accuracy levels through periodic calibration. Airfeel is used as a weather station to measure the potential of renewable energy, especially wind and solar energy. The potential for wind energy is considered from the speed and direction of the wind, while the potential for solar energy is considered from the level of solar irradiation. These parameters allow Airfeel to determine the optimal location for renewable energy generation based on weather conditions. Additionally, the DJI Phantom 4 Pro RTK drone was used for 3D Mapping Photogrammetry. This technology aids in creating three-dimensional maps that are considered in the planning and development of renewable energy power plants at the location. Implementing these two technologies can contribute to future planning for developing other renewable energy sources in Gili Iyang Island.


  • Open Access

    Predictive controllers for synchronous reluctance motor drive systems

    by Muhammad Syahril Mubarok, Nur Vidia Laksmi B., Tian-Hua Liu

    This paper proposes the design and implementation of predictive controllers for synchronous reluctance motor drive systems to enhance their dynamic responses. The predictive speed and current controllers in this paper are designed in systematic procedures. The predictive speed controller is implemented by using Laguerre function procedure. The Laguerre function is used to simplify the algorithm and to minimize the execution time of the digital signal processor. For predictive current controller, a finite control set method improves the current tracking ability. The measured currents are used to predict the future phase-current based on the motor model. The optimal control inputs of both predictive controllers are determined by using a cost function minimization method. Experimental results show the proposed drive system provides a wide adjustable speed range, from 2 r/min to 1800 r/min. It has better performance than a proportional-integral (PI) controller including fast rise time, which is 0.9 second, small steady state error, which is 0.32 r/min, and small current ripples. A 32-bit floating-point digital signal processor, TMS-320-F-28335 DSP, is employed to implement the control algorithms.


  • Constrained Predictive Controllers for High-Performance Sensorless IPMSM Drive Systems With Full-Range Speed Operations

    by Muhammad Syahril Mubarok, Tian-Hua Liu, Seyed Alireza Davari, Jose Rodriguez

    A constrained predictive speed controller with an input current limit and a constrained predictive current controller (CPCC) with an input voltage limit are proposed for high-performance sensorless interior permanent magnet synchronous motor (IPMSM) drive systems. Recent predictive controllers for sensorless IPMSM drives tend to focus on unconstrained predictive controllers, which do not consider the voltage or current limitations of inverters and may cause responses that are not smooth. The proposed constrained predictive controllers in this article solve these problems by imposing constraints in the performance index for real-time optimization. Simplified numerical solutions that use Hildreth quadratic programming are used to identify active constraints, and then the control inputs are limited within their physical ranges. In addition, a simple external load estimator based on the Lyapunov function is designed to compensate for external load disturbances. Moreover, a current-slope-based rotor position estimation method, which does not require any extra hardware or high-frequency signal generators or occupy any dc-link voltage, is implemented to accurately estimate the rotor position and speed. The proposed method in this article improves the dynamic performance and reduces computational complexity when implemented in sensorless IPMSM drive systems. The proposed methods have quick transient responses, excellent load disturbance responses, good tracking capabilities, and good robustness. The sensorless IPMSM drive system proposed in this article is operated at full-range speeds, from 1 to 3000 r/min. Several simulations and experimental results validate the effectiveness of the proposed constrained predictive controllers.


  • Open Access

    An Adjustable Wide-Range Speed-Control Method for Sensorless IPMSM Drive Systems

    by Muhammad Syahril Mubarok, Tian-Hua Liu

    This paper proposes an adjustable wide-range speed-control method for sensorless IPMSM drive systems from standstill, low-speeds, middle-speeds, and high-speeds in the flux-weakening region. A sensorless method and an online parameter estimation method based on the measurement of current-slope under SVPWM with an extension compensation are proposed. The estimated rotor position, rotor speed, d-q axis inductances, magnetic flux, and torque of the IPMSM are precisely computed by using a current-slope measurement, and then a closed-loop speed control sensorless IPMSM drive system is implemented without requiring any external high-frequency signal injection or a complicated observer. In addition, to achieve a high-performance sensorless IPMSM drive system, the estimated parameters are used for real-time maximum torque per ampere control and flux-weakening control. Finally, the proposed sensorless IPMSM drive system provides a wide operation range from 1 r/min to 3000 r/min with excellent performance in constant-torque regions and flux-weakening regions. A digital signal processor, made by Texas Instrument, type TMS 320F2802, is employed to realize the control algorithm and estimation algorithm. Experimental results show the proposed sensorless IPMSM drive system achieves satisfactory responses, including $\pm \,{\mathrm {2.5}}^{\circ }$ of electrical position estimation errors, good dynamic responses, and good tracking responses.


  • Open Access

    Predictive Controllers for Dual-Voltage Vector Current-Slope Sensorless IPMSM Drives

    by Muhammad Syahril Mubarok, Tian-Hua Liu

    A rotor position estimation method based on a dual-voltage vector modulation technique for an IPMSM drive system is proposed in this paper. This method effectively increases the differences of the current slope in each switching state when compared to a single-voltage vector modulation technique, and it improves the current tracking capability of the current control as well as the accuracy of the rotor position estimation. The duty cycles of the dual-voltage vectors are systematically derived to generate the PWM switching states of the inverter. By measuring the current slope in each PWM switching state, the rotor position is easily estimated. In addition, the pulse width of the voltage vectors is not too narrow and does not require any extension or compensation. A predictive speed controller and a predictive current controller are designed and implemented to improve the dynamic responses of the drive system. All of the control algorithms, including dual-voltage vector modulation, rotor position estimation, and predictive control are realized through a DSP TMS-320F-2808. Experimental results show the proposed method provides an adjustable speed from 1 r/min to 2000 r/min with good performance, including transient responses, external load disturbance rejection, reversing speed, and tracking capability.


  • Open Access

    Predictive Controller Design for a Three-Winding Inductive Power Transfer System

    by Tian-Hua Liu, Muhammad Syahril Mubarok, Zheng-Jun Liu

    Inductive power transfer (IPT) systems have become more and more popular recently. To improve transient responses and load disturbance responses, this paper proposes a predictive controller design for a three-winding inductive power transfer (IPT) system. First, a three-winding IPT is presented. Next, a predictive controller is designed based on augmented variables and a performance index. Finally, a digital signal processor, TMS 320F2808, made by Texas Instrument, is used to execute the predictive control algorithms and to control the switching states of the power devices. An IPT system, with DC 220 V input, DC 130 V output, and a rated power of 2 kW, is implemented. A buck converter is used to provide an adjustable output voltage and output current to charge a battery set. Experimental results show that the proposed predictive controllers of the IPT system have better performance than proportional-integral (PI) controllers, including faster transient responses and better load disturbance responses.