Yoga Uta Nugraha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yoga Uta Nugraha has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Muhammad Nur Yuniarto
Institut Teknologi Sepuluh Nopember Jl, AriefRahmanHakim
3 shared publications - Prisma Megantoro
Universitas Airlangga
3 shared publications - Retna Apsari
Department of Engineering, Faculty of Advanced Technology and Multidiscipline, Universitas Airlangga, Indonesia
3 shared publications - Indra Sidharta
Department of Mechanical Engineering, Institut Teknologi Sepuluh Nopember (ITS), Surabaya, Indonesia
2 shared publications - Lilik Jamilatul Awalin
Universitas Airlangga
2 shared publications - Muhammad Syahril Mubarok
Universitas Airlangga
2 shared publications
Latest Publications
- Open Access
- 1 September 2025
- Published by Universitas Airlangga in Jurnal Layanan Masyarakat (Journal of Public Services)
- Vol. 9 (3) , 329-340
IMPLEMENTATION OF HYBRID PLTS AND ELECTRIC BIKES AS AN EFFORT TOWARD GO GREEN TOURISM ON NGIROBOYO BEACH PACITAN
Ngiroboyo Beach in Pacitan Regency has great potential as a tourist destination because of its natural beauty. In addition to having a distinctive sea panorama and black sand, this beach also has interesting geothermal potential to be developed. The potential of Ngiroboyo Beach, which has not been widely explored, has led to this community service program being carried out to develop geothermal tourism destinations based on renewable energy, with a focus on increasing access to environmentally friendly electricity and improving tourism facilities. The stages of the activity include socialization, training, and mentoring for tourism awareness groups (Pokdarwis) regarding the use of renewable energy through the installation of hybrid PLTS and electric bicycles. The installed hybrid PLTS can produce an electricity capacity of around 400 Watts at peak lighting, as a concrete result of the implementation of this program. The electricity generated through the hybrid PLTS can be used for electricity loads for lights and sound systems to support tourism activities. The training was conducted to strengthen the capacity of the community in managing tourism facilities based on renewable energy. The evaluation results showed a positive response from the participants, who expressed high satisfaction with the implementation of the program. This program is expected to be the first step in promoting the concept of sustainable tourism in Pacitan Regency and supporting sustainable development goals (SDGs), especially in the fields of clean energy and sustainable infrastructure.
- 1 September 2025
- Published by Universitas Airlangga in Jurnal Layanan Masyarakat (Journal of Public Services)
- Vol. 9 (3) , 329-340
Open AccessIMPLEMENTATION OF HYBRID PLTS AND ELECTRIC BIKES AS AN EFFORT TOWARD GO GREEN TOURISM ON NGIROBOYO BEACH PACITAN
Ngiroboyo Beach in Pacitan Regency has great potential as a tourist destination because of its natural beauty. In addition to having a distinctive sea panorama and black sand, this beach also has interesting geothermal potential to be developed. The potential of Ngiroboyo Beach, which has not been widely explored, has led to this community service program being carried out to develop geothermal tourism destinations based on renewable energy, with a focus on increasing access to environmentally friendly electricity and improving tourism facilities. The stages of the activity include socialization, training, and mentoring for tourism awareness groups (Pokdarwis) regarding the use of renewable energy through the installation of hybrid PLTS and electric bicycles. The installed hybrid PLTS can produce an electricity capacity of around 400 Watts at peak lighting, as a concrete result of the implementation of this program. The electricity generated through the hybrid PLTS can be used for electricity loads for lights and sound systems to support tourism activities. The training was conducted to strengthen the capacity of the community in managing tourism facilities based on renewable energy. The evaluation results showed a positive response from the participants, who expressed high satisfaction with the implementation of the program. This program is expected to be the first step in promoting the concept of sustainable tourism in Pacitan Regency and supporting sustainable development goals (SDGs), especially in the fields of clean energy and sustainable infrastructure.
- Open Access
- 17 June 2025
- Published by Universitas Airlangga in Jurnal Layanan Masyarakat (Journal of Public Services)
- Vol. 9 (2) , 215-222
ELECTRIC BIKES FOR GREEN MOBILITY IMPROVEMENT IN GILI IYANG, MADURA
This community service program is implemented in an island region that has limited access to electricity and fuel. This program is implemented on Gili Iyang Island, Sumenep, Madura. On the island, the only mode of transportation available is motorbikes and three-wheeled motorbikes due to limited and narrow roads. The price of gasoline reaches two to four times the normal price. Based on these conditions, the issue raised in this community service program is the use of electric bicycles for mobility, with the hope that it can also be a means of supporting the main tourist attraction of the island known as "Oxygen Island". This program is training for the community on how to assemble and maintain electric bicycles. The electric bicycles used in this program are designed with compact and flexible advantages, equipped with lithium batteries with a range of up to 30 km. In addition, there is a pedal assist feature to make it easier to pedal when needed, such as when going uphill or crossing sandy roads. For recharging electric bicycles, a solar shelter is provided, which helps save transportation costs. Training is provided through theoretical and practical materials. Participants can directly implement the theory that has been conveyed when practicing assembling bicycles. Based on the results of the pre and post tests, in general, there was an increase of 17-50% in the knowledge and skills of participants related to the assembly and maintenance of electric bicycles. This is a very strong belief that the Gili Iyang community has been able to use and maintain electric bicycles.
- 17 June 2025
- Published by Universitas Airlangga in Jurnal Layanan Masyarakat (Journal of Public Services)
- Vol. 9 (2) , 215-222
Open AccessELECTRIC BIKES FOR GREEN MOBILITY IMPROVEMENT IN GILI IYANG, MADURA
This community service program is implemented in an island region that has limited access to electricity and fuel. This program is implemented on Gili Iyang Island, Sumenep, Madura. On the island, the only mode of transportation available is motorbikes and three-wheeled motorbikes due to limited and narrow roads. The price of gasoline reaches two to four times the normal price. Based on these conditions, the issue raised in this community service program is the use of electric bicycles for mobility, with the hope that it can also be a means of supporting the main tourist attraction of the island known as "Oxygen Island". This program is training for the community on how to assemble and maintain electric bicycles. The electric bicycles used in this program are designed with compact and flexible advantages, equipped with lithium batteries with a range of up to 30 km. In addition, there is a pedal assist feature to make it easier to pedal when needed, such as when going uphill or crossing sandy roads. For recharging electric bicycles, a solar shelter is provided, which helps save transportation costs. Training is provided through theoretical and practical materials. Participants can directly implement the theory that has been conveyed when practicing assembling bicycles. Based on the results of the pre and post tests, in general, there was an increase of 17-50% in the knowledge and skills of participants related to the assembly and maintenance of electric bicycles. This is a very strong belief that the Gili Iyang community has been able to use and maintain electric bicycles.
- Open Access
- 8 December 2024
- Published by Universitas Airlangga in Jurnal Layanan Masyarakat (Journal of Public Services)
- Vol. 8 (4) , 476-485
UTILIZING 3D MAPPING PHOTOGRAMMETRY AND AIRFEEL WEATHER MONITORING FOR SOLAR AND WIND POWER PLANT DEVELOPMENT PLANNING ON GILI IYANG
This article discusses community service activities on Gili Iyang Island, Sumenep, Madura, which focus on implementing appropriate technology in sensing the potential of renewable energy sources. Gili Iyang Island itself is an area that actively encourages the use of renewable energy. In this activity, maintenance and monitoring of data on AirFeel are carried out, including device checks and monitoring data accuracy levels through periodic calibration. Airfeel is used as a weather station to measure the potential of renewable energy, especially wind and solar energy. The potential for wind energy is considered from the speed and direction of the wind, while the potential for solar energy is considered from the level of solar irradiation. These parameters allow Airfeel to determine the optimal location for renewable energy generation based on weather conditions. Additionally, the DJI Phantom 4 Pro RTK drone was used for 3D Mapping Photogrammetry. This technology aids in creating three-dimensional maps that are considered in the planning and development of renewable energy power plants at the location. Implementing these two technologies can contribute to future planning for developing other renewable energy sources in Gili Iyang Island.
- 8 December 2024
- Published by Universitas Airlangga in Jurnal Layanan Masyarakat (Journal of Public Services)
- Vol. 8 (4) , 476-485
Open AccessUTILIZING 3D MAPPING PHOTOGRAMMETRY AND AIRFEEL WEATHER MONITORING FOR SOLAR AND WIND POWER PLANT DEVELOPMENT PLANNING ON GILI IYANG
This article discusses community service activities on Gili Iyang Island, Sumenep, Madura, which focus on implementing appropriate technology in sensing the potential of renewable energy sources. Gili Iyang Island itself is an area that actively encourages the use of renewable energy. In this activity, maintenance and monitoring of data on AirFeel are carried out, including device checks and monitoring data accuracy levels through periodic calibration. Airfeel is used as a weather station to measure the potential of renewable energy, especially wind and solar energy. The potential for wind energy is considered from the speed and direction of the wind, while the potential for solar energy is considered from the level of solar irradiation. These parameters allow Airfeel to determine the optimal location for renewable energy generation based on weather conditions. Additionally, the DJI Phantom 4 Pro RTK drone was used for 3D Mapping Photogrammetry. This technology aids in creating three-dimensional maps that are considered in the planning and development of renewable energy power plants at the location. Implementing these two technologies can contribute to future planning for developing other renewable energy sources in Gili Iyang Island.
- Open Access
- 1 December 2022
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 13 (4) , 2313-2323
Experimental and simulation approach of cooling system in 3-phase inverter using extended surface
Overheating is a failure mode that significantly affects the reliability of electronic devices. All electronic devices, including a 3-phase inverter driving a traction motor, produce heat dissipation. Heat dissipation needs to be controlled with cooling to prevent overheating. Overheating can be avoided by increasing cooling or reducing heat dissipation. Heat dissipation in the 3-phase inverter is caused by the internal resistance of the metal–oxide–semiconductor field-effect transistor (MOSFET), switching loss, and other factors. Cooling for the 3-phase inverter can use water coolant or air coolant. The cooling system is based on the amount of heat dissipation produced. Cooling of a 3-phase inverter can use air coolant with the addition of an extended surface area in the heat sink. The heat sink uses aluminum material, often called pin fin. There are kinds of aluminum available in the market. We calculated heat generation based on the MOSFET's internal resistance, switching loss, and other factors. We validated the simulation results experimentally using a thermal camera. Thus, we could find an optimal number, dimensions, and aluminum type of fin for the cooling system in the 3-phase inverter.
- 1 December 2022
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 13 (4) , 2313-2323
Open AccessExperimental and simulation approach of cooling system in 3-phase inverter using extended surface
Overheating is a failure mode that significantly affects the reliability of electronic devices. All electronic devices, including a 3-phase inverter driving a traction motor, produce heat dissipation. Heat dissipation needs to be controlled with cooling to prevent overheating. Overheating can be avoided by increasing cooling or reducing heat dissipation. Heat dissipation in the 3-phase inverter is caused by the internal resistance of the metal–oxide–semiconductor field-effect transistor (MOSFET), switching loss, and other factors. Cooling for the 3-phase inverter can use water coolant or air coolant. The cooling system is based on the amount of heat dissipation produced. Cooling of a 3-phase inverter can use air coolant with the addition of an extended surface area in the heat sink. The heat sink uses aluminum material, often called pin fin. There are kinds of aluminum available in the market. We calculated heat generation based on the MOSFET's internal resistance, switching loss, and other factors. We validated the simulation results experimentally using a thermal camera. Thus, we could find an optimal number, dimensions, and aluminum type of fin for the cooling system in the 3-phase inverter.
- Open Access
- 20 June 2022
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 13 (6) , 107
On the Development and Experimental Validation of a Novel and Intuitive Interior Permanent Magnet Synchronous Motor Controller for Electric Vehicle Application
This paper discusses the process of developing a novel and robust algorithm for an interior permanent magnet synchronous motor controller. This is necessary for the simplification of the setting of control parameters and maintaining the proper operation of the motor. A 3D torque lookup table was used in which two inputs were considered, i.e., accelerator movements and the motor rotational speed. These two inputs allowed the lookup table to generate a specified torque at any motor rotation, which was then fed-forward to the field-oriented control and space vector pulse width modulation algorithm. Modeling, simulation, and experimental tests were performed to design and validate the proposed controller. The experimental validation shows that the proposed controller worked as intended. This was indicated by its ability to control the motor to obtain a 7% higher torque output than in the simulation in the constant torque region. In the field-weakening region, the controller could make the motor reach a maximum speed of 5500 RPM. There was only an 8% difference compared to the simulation (6500 RPM). In terms of maximum power generated, the controller was able to match the simulation output with only a 5% difference.
- 20 June 2022
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 13 (6) , 107
Open AccessOn the Development and Experimental Validation of a Novel and Intuitive Interior Permanent Magnet Synchronous Motor Controller for Electric Vehicle Application
This paper discusses the process of developing a novel and robust algorithm for an interior permanent magnet synchronous motor controller. This is necessary for the simplification of the setting of control parameters and maintaining the proper operation of the motor. A 3D torque lookup table was used in which two inputs were considered, i.e., accelerator movements and the motor rotational speed. These two inputs allowed the lookup table to generate a specified torque at any motor rotation, which was then fed-forward to the field-oriented control and space vector pulse width modulation algorithm. Modeling, simulation, and experimental tests were performed to design and validate the proposed controller. The experimental validation shows that the proposed controller worked as intended. This was indicated by its ability to control the motor to obtain a 7% higher torque output than in the simulation in the constant torque region. In the field-weakening region, the controller could make the motor reach a maximum speed of 5500 RPM. There was only an 8% difference compared to the simulation (6500 RPM). In terms of maximum power generated, the controller was able to match the simulation output with only a 5% difference.
- Open Access
- 2 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 48510-48522
Modeling, Simulation, and Validation of An Electric Scooter Energy Consumption Model: A Case Study of Indonesian Electric Scooter
Indonesia has the third-largest motorcycle population in the world. These motorcycles have been known as a source of air pollution. Therefore, shifting the motorcycle to electric-driven based technology is inevitable. However, it is quite challenging as the residents prefer higher performance (in terms of power and speed) of the electric model which is unavailable in the market. Unfortunately, the demand for higher performance models creates other problems, such as the requirement for a bigger battery. This is because there is a range of anxiety phenomena in-vehicle usage. However, the capability to accurately estimate the electric motorcycle’s range does not exist. Therefore, this paper focuses on how to develop an electric scooter model to simulate its performances, especially its range estimation. The modeling approach was the use of an electric scooter longitudinal model developed in MATLAB/Simulink environment. Based on the dimensions and targeted performance, the developed model was simulated to determine its power and energy requirements. It is then validated using an experimental test on a dynamometer and on-road conditions. Based on the experimental data analysis, it can be concluded the developed model is valid and can be used as a basis for the next development of any electric motorcycle.
- 2 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 48510-48522
Open AccessModeling, Simulation, and Validation of An Electric Scooter Energy Consumption Model: A Case Study of Indonesian Electric Scooter
Indonesia has the third-largest motorcycle population in the world. These motorcycles have been known as a source of air pollution. Therefore, shifting the motorcycle to electric-driven based technology is inevitable. However, it is quite challenging as the residents prefer higher performance (in terms of power and speed) of the electric model which is unavailable in the market. Unfortunately, the demand for higher performance models creates other problems, such as the requirement for a bigger battery. This is because there is a range of anxiety phenomena in-vehicle usage. However, the capability to accurately estimate the electric motorcycle’s range does not exist. Therefore, this paper focuses on how to develop an electric scooter model to simulate its performances, especially its range estimation. The modeling approach was the use of an electric scooter longitudinal model developed in MATLAB/Simulink environment. Based on the dimensions and targeted performance, the developed model was simulated to determine its power and energy requirements. It is then validated using an experimental test on a dynamometer and on-road conditions. Based on the experimental data analysis, it can be concluded the developed model is valid and can be used as a basis for the next development of any electric motorcycle.
- 4 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electrification Magazine
- Vol. 10 (1) , 65-74
Indonesian Electric Motorcycle Development: Lessons from innovation-based concept implementation on the design and production of the first Indonesian electric motorcycle
The R&D lead time of a motorcycle from scratch takes roughly five to seven years. This time frame needs to be significantly reduced to develop and produce an electric motorcycle in less than a year. The purpose of this article is to report the designing, testing, and mass production of GESITS, the first electric motorcycle developed in Indonesia. This was a significant development in Indonesian industries because motorcycles before GESISTS were developed by their principal engineers in Japan, India, or China. Due to the short time available for R&D, traditional methods employed by existing automotive industries were not applicable. They operated following the requirements from their motorcycle parent companies, which had gigantic markets, capabilities, and finance. Furthermore, the electric motorcycle industry was not yet ready because the R&D model seemed to be a push rather than pull market production employed by the existing industries. Therefore, a novel methodology and approaches for R&D and production are required. In terms of technology, business model, and company, this motorcycle was novel, meaning it was logical to implement the innovation-based approach to research, develop, and produce the GESITS. Lean start-up methodology governs the R&D process and was used to develop GESITS and its business model in less than two years. Subsequently, GESITS has been mass produced and sold in Indonesia and abroad with sales significantly increasing annually. Therefore, this article shows the successful implementation of the innovation-based concept in new industries—electrical motorcycles.
- 4 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electrification Magazine
- Vol. 10 (1) , 65-74
Indonesian Electric Motorcycle Development: Lessons from innovation-based concept implementation on the design and production of the first Indonesian electric motorcycle
The R&D lead time of a motorcycle from scratch takes roughly five to seven years. This time frame needs to be significantly reduced to develop and produce an electric motorcycle in less than a year. The purpose of this article is to report the designing, testing, and mass production of GESITS, the first electric motorcycle developed in Indonesia. This was a significant development in Indonesian industries because motorcycles before GESISTS were developed by their principal engineers in Japan, India, or China. Due to the short time available for R&D, traditional methods employed by existing automotive industries were not applicable. They operated following the requirements from their motorcycle parent companies, which had gigantic markets, capabilities, and finance. Furthermore, the electric motorcycle industry was not yet ready because the R&D model seemed to be a push rather than pull market production employed by the existing industries. Therefore, a novel methodology and approaches for R&D and production are required. In terms of technology, business model, and company, this motorcycle was novel, meaning it was logical to implement the innovation-based approach to research, develop, and produce the GESITS. Lean start-up methodology governs the R&D process and was used to develop GESITS and its business model in less than two years. Subsequently, GESITS has been mass produced and sold in Indonesia and abroad with sales significantly increasing annually. Therefore, this article shows the successful implementation of the innovation-based concept in new industries—electrical motorcycles.