Piotr Sokolski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Piotr Sokolski has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Justyna Sokolska
Department of Fundamentals of Machine Design and Mechatronic Systems, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, ul. I. Lukasiewicza 5, 50-371 Wroclaw, Poland
3 shared publications Marek Sokolski
Wroclaw University of Science and Technology
2 shared publications- Tadeusz Smolnicki
Wroclaw University of Science and Technology
2 shared publications Justyna Sokolska
Wroclaw University of Science and Technology
1 shared publication- Robert Czabanowski
Faculty of Mechanical Engineering, Wrocław University of Science and Technology, Wybrzeże Wyspiańskiego 27, 50-370 Wrocław, Poland
1 shared publication
Latest Publications
- Open Access
- 5 July 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (13) , 7568
Effect of Grain Size and Incidence Angle on Erosive Wear of Polyurea Coating
This study investigated the erosive wear of a polyurea coating with a hardness of 95 ShA and a thickness of 3 mm applied to a 3 mm thick plate made of S235 steel. The process of erosive wear was carried out using a stream of compressed air containing abrasive grains of aluminum oxide (Al2O3). The erosive wear was studied using different incidence angles (45°, 60° and 90°) and erosive grain sizes. Thus, the effects of the incidence angle and erosive grain size on the erosive wear of the polyurea coating were analyzed. Erosive wear was determined as linear wear: the depth of the wear trace was measured using an optical profilometer. This study showed a non-linear correlation between erosive wear, incidence angle and erosive particle size. In addition, a qualitative study of the surface of the coating after a wear test was carried out using a scanning electron microscope, which made it possible to describe the mechanisms of erosive wear of the polyurea coating.
- 5 July 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (13) , 7568
Open AccessEffect of Grain Size and Incidence Angle on Erosive Wear of Polyurea Coating
This study investigated the erosive wear of a polyurea coating with a hardness of 95 ShA and a thickness of 3 mm applied to a 3 mm thick plate made of S235 steel. The process of erosive wear was carried out using a stream of compressed air containing abrasive grains of aluminum oxide (Al2O3). The erosive wear was studied using different incidence angles (45°, 60° and 90°) and erosive grain sizes. Thus, the effects of the incidence angle and erosive grain size on the erosive wear of the polyurea coating were analyzed. Erosive wear was determined as linear wear: the depth of the wear trace was measured using an optical profilometer. This study showed a non-linear correlation between erosive wear, incidence angle and erosive particle size. In addition, a qualitative study of the surface of the coating after a wear test was carried out using a scanning electron microscope, which made it possible to describe the mechanisms of erosive wear of the polyurea coating.
- Open Access
- 28 June 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (13) , 7299
Load-Carrying Capacity Tests on Innovative Friction-Bolted Joints and Prototype Bolted Interconnection Nodes
This study deals with innovative friction-bolted joints. The innovative bolted joints were designed for load-bearing structures of light cranes with spans up to 18 m and lifting capacities up to 160 kN, or similar load-bearing structures. The practical suitability of these connectors for use in the screw connection nodes of headframes with girders in light overhead cranes was confirmed by the positive results of experimental verification and experimental testing on physical models of these nodes. Specific elements were created and used in these joints, and several models were examined. The analyzed friction-bolted joints were found to have an increased load capacity when compared with typical assemblies. If using screws of higher strength grades, shortening the preparation of those joints is possible.
- 28 June 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (13) , 7299
Open AccessLoad-Carrying Capacity Tests on Innovative Friction-Bolted Joints and Prototype Bolted Interconnection Nodes
This study deals with innovative friction-bolted joints. The innovative bolted joints were designed for load-bearing structures of light cranes with spans up to 18 m and lifting capacities up to 160 kN, or similar load-bearing structures. The practical suitability of these connectors for use in the screw connection nodes of headframes with girders in light overhead cranes was confirmed by the positive results of experimental verification and experimental testing on physical models of these nodes. Specific elements were created and used in these joints, and several models were examined. The analyzed friction-bolted joints were found to have an increased load capacity when compared with typical assemblies. If using screws of higher strength grades, shortening the preparation of those joints is possible.
- Open Access
Suitability of Selected Diagnostic Factors for Assessing the Technical Condition of the Working Systems of Bucket Elevators
This article proposes a method for diagnosing the main systems of bucket elevators in order to ensure their reliable operation. This method employs diagnostic indices of vibration velocity and vibration acceleration, which were deemed useful based on tests performed on four bucket elevators operating in a research laboratory and in a power plant. This article also analyzes other indicators, such as the coefficient of variation, skewness, kurtosis, crest factor, and quantile peak factor, and demonstrates the usefulness of kurtosis for diagnostic evaluation. Additionally, it proposes using the quantile peak factor as an alternative to the crest factor. This study estimates the statistical distributions of diagnostic signals and presents the results in the form of histograms. This is followed by the detection of outliers in all measurement series. Based on the results of the performed tests and their analysis, recommendations are made for diagnosing bucket elevators.
Open AccessSuitability of Selected Diagnostic Factors for Assessing the Technical Condition of the Working Systems of Bucket Elevators
This article proposes a method for diagnosing the main systems of bucket elevators in order to ensure their reliable operation. This method employs diagnostic indices of vibration velocity and vibration acceleration, which were deemed useful based on tests performed on four bucket elevators operating in a research laboratory and in a power plant. This article also analyzes other indicators, such as the coefficient of variation, skewness, kurtosis, crest factor, and quantile peak factor, and demonstrates the usefulness of kurtosis for diagnostic evaluation. Additionally, it proposes using the quantile peak factor as an alternative to the crest factor. This study estimates the statistical distributions of diagnostic signals and presents the results in the form of histograms. This is followed by the detection of outliers in all measurement series. Based on the results of the performed tests and their analysis, recommendations are made for diagnosing bucket elevators.
- Open Access
Assessment of Suitability for Long-Term Operation of a Bucket Elevator: A Case Study
Bucket elevators generally operate on a 24/7 basis, and for this reason, one of the main requirements is their high reliability. This reliability can be ensured, among other things, by assessing the technical condition of drive assemblies and working assemblies and taking appropriate measures. Carrying out diagnostic measurements enables periodical monitoring of those mechanisms. Vibroacoustic methods are usually employed in operating conditions to measure vibration velocity and acceleration at specific points, and are used as diagnostic signals. This paper presents the results of tests of the intensity of vibrations generated in the drive unit of a large industrial bucket elevator. The analysis of the results in the time domain and frequency domain served as the basis for evaluating the suitability of the drive, and thus the elevator, for long-term operation.
Open AccessAssessment of Suitability for Long-Term Operation of a Bucket Elevator: A Case Study
Bucket elevators generally operate on a 24/7 basis, and for this reason, one of the main requirements is their high reliability. This reliability can be ensured, among other things, by assessing the technical condition of drive assemblies and working assemblies and taking appropriate measures. Carrying out diagnostic measurements enables periodical monitoring of those mechanisms. Vibroacoustic methods are usually employed in operating conditions to measure vibration velocity and acceleration at specific points, and are used as diagnostic signals. This paper presents the results of tests of the intensity of vibrations generated in the drive unit of a large industrial bucket elevator. The analysis of the results in the time domain and frequency domain served as the basis for evaluating the suitability of the drive, and thus the elevator, for long-term operation.
- 29 November 2023
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 26 (1)
Strength analysis of welded joints in support structures of heavy machinery subjected to changeable loading conditions
The durability of bearing units of large machines depends mainly on the condition of their welded joints. With this in mind, we developed numerical models of the analyzed bearing units, for which we performed FEM simulations of the stresses in welded joints in several basic load cases. In each of the respective variants the technical condition of the bearing nodes was different and it corresponded to the severity of the degradation processes. Different positions of the superstructure in relation to the undercarriage were also taken into account. The simulations used the hot-spot method dedicated to FEM analyses of complex welded structures. We discovered that the loads have a significant influence on the values and distribution of von Mises principal stresses and their axial components. Based on the carried out analyses, we identified the most unfavorable load cases that generate the highest stresses in the welded joints of the assessed nodes. We also demonstrated that the applied method effectively assesses the stresses of welded joints subjected to variable working loads.
- 29 November 2023
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 26 (1)
Strength analysis of welded joints in support structures of heavy machinery subjected to changeable loading conditions
The durability of bearing units of large machines depends mainly on the condition of their welded joints. With this in mind, we developed numerical models of the analyzed bearing units, for which we performed FEM simulations of the stresses in welded joints in several basic load cases. In each of the respective variants the technical condition of the bearing nodes was different and it corresponded to the severity of the degradation processes. Different positions of the superstructure in relation to the undercarriage were also taken into account. The simulations used the hot-spot method dedicated to FEM analyses of complex welded structures. We discovered that the loads have a significant influence on the values and distribution of von Mises principal stresses and their axial components. Based on the carried out analyses, we identified the most unfavorable load cases that generate the highest stresses in the welded joints of the assessed nodes. We also demonstrated that the applied method effectively assesses the stresses of welded joints subjected to variable working loads.
- 1 March 2022
- Published by Silesian University of Technology in Transport Problems
- Vol. 17 (1) , 187-200
ASSESSMENT OF THE ACOUSTIC MICROCLIMATE AND RATING OF NOISE HAZARDS IN THE INNER TRANSPORT SYSTEM OF A BUCKET WHEEL EXCAVATOR: A CASE STUDY
- 1 March 2022
- Published by Silesian University of Technology in Transport Problems
- Vol. 17 (1) , 187-200
ASSESSMENT OF THE ACOUSTIC MICROCLIMATE AND RATING OF NOISE HAZARDS IN THE INNER TRANSPORT SYSTEM OF A BUCKET WHEEL EXCAVATOR: A CASE STUDY
- Open Access
A Method of Comparative Evaluation of the Drive Units of Two Bucket Elevators—A Case Study
Bucket elevators are applied in many industries for bulk material handling. One of the main requirements for these devices is their high operational reliability. This applies in particular to power units that must operate continuously without failure. This article presents a comparative assessment of the drive units of two bucket elevators. The vibration intensity of their bearing units was used as the basis for the comparison. The evaluation was carried out using three independent methods based on the vibration velocity analysis: in the time domain, in the frequency domain and using the probabilistic approach.
Open AccessA Method of Comparative Evaluation of the Drive Units of Two Bucket Elevators—A Case Study
Bucket elevators are applied in many industries for bulk material handling. One of the main requirements for these devices is their high operational reliability. This applies in particular to power units that must operate continuously without failure. This article presents a comparative assessment of the drive units of two bucket elevators. The vibration intensity of their bearing units was used as the basis for the comparison. The evaluation was carried out using three independent methods based on the vibration velocity analysis: in the time domain, in the frequency domain and using the probabilistic approach.
- Open Access
A Method for Monitoring the Technical Condition of Large-Scale Bearing Nodes in the Bodies of Machines Operating for Extended Periods of Time
Failure of systems applied in machines comprising rolling and slewing bearings usually causes downtime of the entire heavy machine. The problem of failures can be aggravated by extremely difficult operating conditions, such as significant loads or a harsh environment. The entire issue inspired us to develop a method of monitoring the condition of such units. A study was carried out for six different large-scale excavators which examined strain distributions in the tested subassemblies. In order to estimate the technical condition of wheeled bogies, we used the phenomenon of strain propagation caused by the concentrated force acting in the ring girder web. Flamant theory was utilized to describe this phenomenon. Measurements were performed using strain gauges and the obtained results were compared with the FEM model. To determine whether bearing joints were in a good or bad condition, a coefficient of variation and an impulse factor were introduced as diagnostic indicators. It turned out that by evaluating these indicators, it was possible to distinguish between these two conditions. The method was successfully validated on machines that are in operation.
Open AccessA Method for Monitoring the Technical Condition of Large-Scale Bearing Nodes in the Bodies of Machines Operating for Extended Periods of Time
Failure of systems applied in machines comprising rolling and slewing bearings usually causes downtime of the entire heavy machine. The problem of failures can be aggravated by extremely difficult operating conditions, such as significant loads or a harsh environment. The entire issue inspired us to develop a method of monitoring the condition of such units. A study was carried out for six different large-scale excavators which examined strain distributions in the tested subassemblies. In order to estimate the technical condition of wheeled bogies, we used the phenomenon of strain propagation caused by the concentrated force acting in the ring girder web. Flamant theory was utilized to describe this phenomenon. Measurements were performed using strain gauges and the obtained results were compared with the FEM model. To determine whether bearing joints were in a good or bad condition, a coefficient of variation and an impulse factor were introduced as diagnostic indicators. It turned out that by evaluating these indicators, it was possible to distinguish between these two conditions. The method was successfully validated on machines that are in operation.
- 13 October 2019
- Published by Springer Nature
- p. 93-114
Problems of Noise Hazards in Long-Term Operated Basic Machinery for Open-Pit Mining
- 13 October 2019
- Published by Springer Nature
- p. 93-114
Problems of Noise Hazards in Long-Term Operated Basic Machinery for Open-Pit Mining
- 10 March 2019
- Published by Springer Nature in Lecture Notes in Mechanical Engineering
- p. 696-704
Problems of Strength Estimation of the Vulnerable Zones in the Tools of Hydraulic Hammers for Mining
- 10 March 2019
- Published by Springer Nature in Lecture Notes in Mechanical Engineering
- p. 696-704
Problems of Strength Estimation of the Vulnerable Zones in the Tools of Hydraulic Hammers for Mining