Ram Chandra Adhikari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ram Chandra Adhikari has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- David Howe Wood
University of Calgary, Canada
9 shared publications M. Pahlevani
3 shared publicationsD.H. Wood
2 shared publications- Dawood Shekari Beyragh
Department of Electrical and Computer Engineering, University of Calgary, Calgary, AB T2N 1N4, Canada
2 shared publications - Majid Pahlevani
Power Laboratory, Electrical and Computer Engineering Department, Queen’s University, Kingston, ON K7L 3N6, Canada
2 shared publications - Jerson Rogério Pinheiro Vaz
Universidade Federal do Pará, Brasil
1 shared publication
Latest Publications
- 19 February 2021
- Published by ASME International in Journal of Electronic Packaging
- Vol. 143 (3)
Design, Fabrication, and Testing of a Novel Design for Flexible Light-Emitting Diode Signage Modules
This paper presents a new design architecture for mechanically flexible light-emitting diode (LED) signage modules for applications in digital advertising on curved surfaces. The new design comprises an array of commonly used rigid printed circuit boards (PCBs) but of smaller size with some spacing between them, which is encapsulated by a flexible substrate or potting material, instead of a large single rigid PCB in the entire LED module as in the case of conventional LED signage modules. Commonly used through-hole type red-green-blue (RGB) LEDs are considered. To demonstrate the design, manufacturing, and mechanical flexibility of the design, a prototype LED signage module with a typical industry standard size of 304 mm × 304 mm × 10 mm was designed and fabricated. Experimental testing and finite element simulations were conducted to analyze mechanical flexibility and internal stresses in the module. The results demonstrate that the new design provides flexible LED modules, without altering the conventional LED control system. It is shown that maximum stress occurs in the spacing between the PCBs and is small even for large module deflection. As the curvature of module deflection was decreased, the maximum stress increased, indicating an important design parameter for the module deflection. The proposed design architecture will enable both indoor and outdoor digital advertising using billboards on a wide range of curved surfaces.
- 19 February 2021
- Published by ASME International in Journal of Electronic Packaging
- Vol. 143 (3)
Design, Fabrication, and Testing of a Novel Design for Flexible Light-Emitting Diode Signage Modules
This paper presents a new design architecture for mechanically flexible light-emitting diode (LED) signage modules for applications in digital advertising on curved surfaces. The new design comprises an array of commonly used rigid printed circuit boards (PCBs) but of smaller size with some spacing between them, which is encapsulated by a flexible substrate or potting material, instead of a large single rigid PCB in the entire LED module as in the case of conventional LED signage modules. Commonly used through-hole type red-green-blue (RGB) LEDs are considered. To demonstrate the design, manufacturing, and mechanical flexibility of the design, a prototype LED signage module with a typical industry standard size of 304 mm × 304 mm × 10 mm was designed and fabricated. Experimental testing and finite element simulations were conducted to analyze mechanical flexibility and internal stresses in the module. The results demonstrate that the new design provides flexible LED modules, without altering the conventional LED control system. It is shown that maximum stress occurs in the spacing between the PCBs and is small even for large module deflection. As the curvature of module deflection was decreased, the maximum stress increased, indicating an important design parameter for the module deflection. The proposed design architecture will enable both indoor and outdoor digital advertising using billboards on a wide range of curved surfaces.
- Open Access
A Numerical and Experimental Study of a Novel Heat Sink Design for Natural Convection Cooling of LED Grow Lights
Light-emitting diode (LED) grow lights are increasingly used in large-scale indoor farming to provide controlled light intensity and spectrum to maximize photosynthesis at various growth stages of plants. As well as converting electricity into light, the LED chips generate heat, so the boards must be properly cooled to maintain the high efficiency and reliability of the LED chips. Currently, LED grow lights are cooled by forced convection air cooling, the fans of which are often the points of failure and also consumers of a significant amount of power. Natural convection cooling is promising as it does not require any moving parts, but one major design challenge is to improve its relatively low heat transfer rate. This paper presents a novel heat sink design for natural convection cooling of LED grow lights. The new design consists of a large rectangular fin array with openings in the base transverse to the fins to increase air flow, and hence the heat transfer. Numerical simulations and experimental testing of a prototype LED grow light with the new heat sink showed that openings achieved their intended purpose. It was found that the new heat sink can transfer the necessary heat flux within the safe operating temperature range of LED chips, which is adequate for cooling LED grow lights.
Open AccessA Numerical and Experimental Study of a Novel Heat Sink Design for Natural Convection Cooling of LED Grow Lights
Light-emitting diode (LED) grow lights are increasingly used in large-scale indoor farming to provide controlled light intensity and spectrum to maximize photosynthesis at various growth stages of plants. As well as converting electricity into light, the LED chips generate heat, so the boards must be properly cooled to maintain the high efficiency and reliability of the LED chips. Currently, LED grow lights are cooled by forced convection air cooling, the fans of which are often the points of failure and also consumers of a significant amount of power. Natural convection cooling is promising as it does not require any moving parts, but one major design challenge is to improve its relatively low heat transfer rate. This paper presents a novel heat sink design for natural convection cooling of LED grow lights. The new design consists of a large rectangular fin array with openings in the base transverse to the fins to increase air flow, and hence the heat transfer. Numerical simulations and experimental testing of a prototype LED grow light with the new heat sink showed that openings achieved their intended purpose. It was found that the new heat sink can transfer the necessary heat flux within the safe operating temperature range of LED chips, which is adequate for cooling LED grow lights.
- 1 June 2020
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 17
Optimizing rectangular fins for natural convection cooling using CFD
- 1 June 2020
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 17
Optimizing rectangular fins for natural convection cooling using CFD
- 30 December 2018
- Published by Springer Nature
- p. 80-92
Nozzle Entry Effects and Cavitation Inception in Crossflow Hydroturbines
- 30 December 2018
- Published by Springer Nature
- p. 80-92
Nozzle Entry Effects and Cavitation Inception in Crossflow Hydroturbines
- Open Access
Computational Analysis of a Double-Nozzle Crossflow Hydroturbine
The crossflow turbines commonly used in small hydropower systems have a single nozzle. We are unaware of any studies of double-nozzle crossflow turbines which could have twice the power output of the single-nozzle design by doubling the flow through the same runner, with a high maximum efficiency. We present a computational analysis of a double-nozzle crossflow turbine, to determine the turbine efficiency and fundamental flow patterns. This work was based on a single-nozzle crossflow turbine with a maximum efficiency of 88%,
Open AccessComputational Analysis of a Double-Nozzle Crossflow Hydroturbine
The crossflow turbines commonly used in small hydropower systems have a single nozzle. We are unaware of any studies of double-nozzle crossflow turbines which could have twice the power output of the single-nozzle design by doubling the flow through the same runner, with a high maximum efficiency. We present a computational analysis of a double-nozzle crossflow turbine, to determine the turbine efficiency and fundamental flow patterns. This work was based on a single-nozzle crossflow turbine with a maximum efficiency of 88%,
- 1 August 2018
- Published by Elsevier in Energy for Sustainable Development
- Vol. 45, 38-45
Computational analysis of part-load flow control for crossflow hydro-turbines
- 1 August 2018
- Published by Elsevier in Energy for Sustainable Development
- Vol. 45, 38-45
Computational analysis of part-load flow control for crossflow hydro-turbines
- Open Access
The Design of High Efficiency Crossflow Hydro Turbines: A Review and Extension
Efficiency is a critical consideration in the design of hydro turbines. The crossflow turbine is the cheapest and easiest hydro turbine to manufacture and so is commonly used in remote power systems for developing countries. A longstanding problem for practical crossflow turbines is their lower maximum efficiency compared to their more advanced counterparts, such as Pelton and Francis turbines. This paper reviews the experimental and computational studies relevant to the design of high efficiency crossflow turbines. We concentrate on the studies that have contributed to designs with efficiencies in the range of 88–90%. Many recent studies have been conducted on turbines of low maximum efficiency, which we believe is due to misunderstanding of design principles for achieving high efficiencies. We synthesize the key results of experimental and computational fluid dynamics studies to highlight the key fundamental design principles for achieving efficiencies of about 90%, as well as future research and development areas to further improve the maximum efficiency. The main finding of this review is that the total conversion of head into kinetic energy in the nozzle and the matching of nozzle and runner designs are the two main design requirements for the design of high efficiency turbines.
Open AccessThe Design of High Efficiency Crossflow Hydro Turbines: A Review and Extension
Efficiency is a critical consideration in the design of hydro turbines. The crossflow turbine is the cheapest and easiest hydro turbine to manufacture and so is commonly used in remote power systems for developing countries. A longstanding problem for practical crossflow turbines is their lower maximum efficiency compared to their more advanced counterparts, such as Pelton and Francis turbines. This paper reviews the experimental and computational studies relevant to the design of high efficiency crossflow turbines. We concentrate on the studies that have contributed to designs with efficiencies in the range of 88–90%. Many recent studies have been conducted on turbines of low maximum efficiency, which we believe is due to misunderstanding of design principles for achieving high efficiencies. We synthesize the key results of experimental and computational fluid dynamics studies to highlight the key fundamental design principles for achieving efficiencies of about 90%, as well as future research and development areas to further improve the maximum efficiency. The main finding of this review is that the total conversion of head into kinetic energy in the nozzle and the matching of nozzle and runner designs are the two main design requirements for the design of high efficiency turbines.
- 1 December 2017
- Published by Elsevier in Energy for Sustainable Development
- Vol. 41, 139-148
A new nozzle design methodology for high efficiency crossflow hydro turbines
- 1 December 2017
- Published by Elsevier in Energy for Sustainable Development
- Vol. 41, 139-148
A new nozzle design methodology for high efficiency crossflow hydro turbines