Louis-Michel Collin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Louis-Michel Collin has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Luc Guy Frechette
Université de Sherbrooke
3 shared publications - Jérôme Barrau
Universitat de Lleida, Lleida, Spain
2 shared publications - Montse Vilarrubí
Dynamic Systems Applied to Solar Energy Research Group, University of Lleida, Lleida, Spain
2 shared publications Perceval Coudrain
2 shared publications- Abdelkader Souifi
Laboratoire des Technologies de la Microlectronique, Laboratoire Ampre, National Institute of Applied Sciences, Villeurbanne cedex, France
1 shared publication Amrid Amnache
1 shared publication
Latest Publications
- 17 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 29 (5) , 769-775
Fabrication and Demonstration of a Self-Adaptive Microvalve Array for Distributed Liquid Cooling in Microelectronic Interposers
We demonstrated the implementation and self-adaptive behavior of an array of thermostatic microvalves that locally control the water-cooling flow to prevent hot spots in microelectronics while minimizing the pumping power. This strategy enables the compact integration of multiple chips on an interposer without constraints of overheating or thermal cross talk. The performance of microfluidic cell array with self-adaptive valve is assessed experimentally, and compared to other conventional microchannel cooling device showing high efficiency and temperature uniformity. This paper presents the first MEMS implementation and experimental demonstration of this concept, which is part of the STREAMS European project. [2020-0198]
- 17 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 29 (5) , 769-775
Fabrication and Demonstration of a Self-Adaptive Microvalve Array for Distributed Liquid Cooling in Microelectronic Interposers
We demonstrated the implementation and self-adaptive behavior of an array of thermostatic microvalves that locally control the water-cooling flow to prevent hot spots in microelectronics while minimizing the pumping power. This strategy enables the compact integration of multiple chips on an interposer without constraints of overheating or thermal cross talk. The performance of microfluidic cell array with self-adaptive valve is assessed experimentally, and compared to other conventional microchannel cooling device showing high efficiency and temperature uniformity. This paper presents the first MEMS implementation and experimental demonstration of this concept, which is part of the STREAMS European project. [2020-0198]
- 1 November 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 144, 71-80
Numerical parametric study of a hotspot-targeted microfluidic cooling array for microelectronics
- 1 November 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 144, 71-80
Numerical parametric study of a hotspot-targeted microfluidic cooling array for microelectronics
- 8 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 9 (3) , 434-445
Add-On Microchannels for Hotspot Thermal Management of Microelectronic Chips in Compact Applications
This work demonstrates an experimental microchannel solution to cool microelectronic chips with hot spots, using an integrated, yet non-intrusive technique. In microelectronics, approaches such as die thinning induce acute stress on cooling because it increases the hot spot phenomena and reduces chip bulk thickness that could be used for microchannels. In compact devices, heat must be removed using limited pumping power and cooling space. Microchannels etched in the backside of the chip, usually considered as an efficient cooling solution, are impracticable on highly thinned chips. This work experimentally investigates the cooling performance of a non-invasive and hot spot aware microchannel die that is in direct fluidic contact with the backside of the microelectronic chip. It also proposes a confinement-wise metric. A thermal resistance of 2.8 °C/W is achieved at a heat flux of 812 W/cm2 per heat source, for a total dissipated power of 20 W and a maximum allowed temperature rise of 55 °C. Such performance is obtained with only 19.2 kPa of pressure drop and 9.4 ml/min of flow rate, corresponding to a hydraulic power of only 3 mW and a coefficient of performance of 6 500. In addition, the complete chip stack, including the thinned chip, measures only 660 μm high. Therefore, backside cooling appears to be a promising compact and low consumption solution for compact electronic applications having confined hot spots.
- 8 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 9 (3) , 434-445
Add-On Microchannels for Hotspot Thermal Management of Microelectronic Chips in Compact Applications
This work demonstrates an experimental microchannel solution to cool microelectronic chips with hot spots, using an integrated, yet non-intrusive technique. In microelectronics, approaches such as die thinning induce acute stress on cooling because it increases the hot spot phenomena and reduces chip bulk thickness that could be used for microchannels. In compact devices, heat must be removed using limited pumping power and cooling space. Microchannels etched in the backside of the chip, usually considered as an efficient cooling solution, are impracticable on highly thinned chips. This work experimentally investigates the cooling performance of a non-invasive and hot spot aware microchannel die that is in direct fluidic contact with the backside of the microelectronic chip. It also proposes a confinement-wise metric. A thermal resistance of 2.8 °C/W is achieved at a heat flux of 812 W/cm2 per heat source, for a total dissipated power of 20 W and a maximum allowed temperature rise of 55 °C. Such performance is obtained with only 19.2 kPa of pressure drop and 9.4 ml/min of flow rate, corresponding to a hydraulic power of only 3 mW and a coefficient of performance of 6 500. In addition, the complete chip stack, including the thinned chip, measures only 660 μm high. Therefore, backside cooling appears to be a promising compact and low consumption solution for compact electronic applications having confined hot spots.