MRMark J. Raine

Mark J. Raine

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mark J. Raine has a total of 55 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    European Nb3Sn and Nb–Ti strand verification for ITER: processing, measurements and statistical analysis

    by M J Raine, T Boutboul, P Readman, D P Hampshire

    We present a large quantity ( ∼ 13000 ) of verification measurements (critical current (I c), n-value, hysteresis loss (Q), residual resistivity ratio (RRR), twist-pitch, diameter, plating thickness and copper-non-copper ratio) and statistical analysis of internal tin and bronze route (BR) Nb3Sn and Nb–Ti strands used in the ITER tokamak magnet system. The Durham laboratory partnered the relevant manufacturer and each independently processed-and-measured one of two short adjacent strands taken from the ends of thousands of piece-lengths, typically several kilometres long. Processing included heat-treatment of the Nb3Sn, which is an irreversible process (i.e. destructive of as-supplied strands). Here we show that when repeat processing-and-measurement of the same piece of Nb3Sn strand is not possible, although the similarity between adjacent strands is not known a priori, processing-and-measuring adjacent strands provides a proxy for single lab (with repeat) measurements or round-robin measurements (without processing). Processing-and-measuring adjacent strands provides limits for the errors introduced by laboratories and for the variability of the piece-lengths, rather than the specific values that round-robin measurements provide. This is because it is not possible to distinguish whether unidentified sources of error come from the differences between adjacent strands or from unidentified laboratory errors, such as from gas impurities during heat-treatment or strand handling. We categorise different types of processing-and-measurement: one type includes I c of BR Nb3Sn where the maximum lab errors are similar to the well-known estimated lab errors that are found using, for example, the commercially specified accuracy of the instruments. Furthermore, the possibility of unidentified sources of random lab error is excluded, and both piece-length variability and lab errors are specified—similar to round-robin measurements. In another type (e.g. RRR or Q of internal tin Nb3Sn), larger than expected variances are measured and unidentified sources of error operate. Categorising the different types of processing-and-measurement helps identify routes to improvement.


  • International Round-Robin Test of Critical Current of Superconducting Cable Sample

    by T. Matsushita, M. Kiuchi, T. Masuda, S. Mukoyama, K. Funaki, J. Cho, J. Lu, M. J. Raine, L. Quéval, F. Trillaud, et al.

    Ten institutes from six countries participated in an international round-robin test to evaluate the critical current of a superconducting power cable made of Bi-2223 tapes. The cable design featured a two-layer inner core conductor and a single-layer outer shield conductor. The shield layer measured approximately 40 mm in diameter, and the cable length was 2.0 m. To eliminate the influence of resistive voltage drops from current transfer, voltage taps for measurement were positioned at a sufficient distance from the current terminals. The critical current was determined using the resistive method with the electric field criterion of 1.0 ${\rm{\mu V}}/\text{cm}$ . In addition, the $n$ -value, an optional parameter reflecting the current–voltage ( $I$ – $V$ ) characteristics, was extracted from the $I$ – $V$ curve within an electric field range of 0.1–1.0 ${\rm{\mu V}}/\text{cm}$ . A detailed uncertainty analysis was conducted for both the critical current and the $n$ -value. Finally, this article discusses the potential for standardization of the employed resistive measurement method.


  • Resistivity Measurements of the Strain, Temperature and Angular Dependence of the Upper Critical Field of REBCO Tapes up to 8 T

    by E. G. Gillard, M. J. Raine, D. P. Hampshire

    The design and operation of a miniature strain-board for measuring the resistivity of high temperature superconducting tapes as a function of uniaxial strain ( $\epsilon$ ) are described. It was used inside a Physical Property Measurement System (PPMS) that provides access to high fields, variable temperature, and a rotator that can vary the angle of the sample with respect to the field. Resistivity measurements made using the strain-board over the strain range 0% to $-1.1$ % in-field are presented for a REBCO (REBa $_{2}$ Cu $_{3}$ O $_{7}$ , RE: Rare-earth element) tape from SuperPower with artificial pinning centres (APC). Values of the upper critical field ( $B_{c2}$ ) were extracted from the resistivity data. We found that although the temperature and angular dependence of B $_{c2}$ were similar to that found in previous studies using ac susceptibility measurements (i.e. the temperature index, $n = 1.2$ , the anisotropy constant, $\gamma = 1.4$ and the interlayer spacing $s = 12$ Å), the upper critical field we found was almost strain independent and therefore quite different. We explain these results by considering the bimodal behaviour of REBCO under strain that is found in single crystal data, and the large parallel shunt the strain-board provided in the measurements. In our resistivity measurements, $B_{c2}$ is determined by a small percolative supercurrent that preferentially flows through material with the highest critical parameters. Conversely, resistivity measurements at high currents, or ac susceptibility measurements, characterise the material with average or low critical parameters from the broad distribution of critical parameters produced in REBCO tapes under strain.


  • HTS Cable International Round Robin: 4.4 kA Critical Current Measurements

    by R. G. Hutson, M. J. Raine, M. Kiuchi, T. Matsushita, D. P. Hampshire

    The critical current of the core and shield of a 2.1 m long, 40 mm diameter Bi-2223 HTS coaxial cable was measured as part of an International Round Robin organised by Japan involving several international laboratories. In Durham, we found using a 100 $\upmu$ Vm $^{-1}$ criterion and an 8 minute trace time that I $_{c}$ of the core and shield were 4386 A and 4143 A and the n -values were 19.6 and 14.4 respectively. 8 minute trace times were found to be a practical approximation of steady state conditions, with critical current values 0.5 % and 1.2 % larger than values obtained using 2 minute trace times, and n -values not significantly different to 2 minute trace values. Two minute trace time data were compared with equivalent data from other participating labs and excellent agreement was found: I $_{c}$ was 0.6 % and 1.5 % larger for the core and shield respectively. The E -field range has a significant effect on the n -value measurements, which varied between groups. Good agreement between the participants for the shield was found for electric fields below 100 $\upmu$ Vm $^{-1}$ , although larger n -values were found at higher electric fields at Durham and some other laboratories. The polarity of the current and the proximity of the return power cable were demonstrated to have negligible effect ( $< $ 0.1 % ) on the I $_{c}$ measurements. Removing conductive and ferromagnetic materials that were part of Durham's experimental set-up increased I $_{c}$ by $< $ 1 % . An intrinsic trace time dependency was found for I $_{c}$ for trace times of less than 8 minutes that we attribute to the time required for fluxons to equilibrate with the underlying pinning landscape in a changing net magnetic field.


  • Open Access

    Successful production of Solution Blow Spun YBCO+Ag complex ceramics

    by A. L. Pessoa, M. J. Raine, D. P. Hampshire, D. K. Namburi, J. H. Durrell, R. Zadorosny

    YBCO fabrics composed of nanowires, produced by solution blow spinning (SBS) are so brittle that the Lorentz force produced by induced currents can be strong enough to damage them. On the other hand, it is known that silver addition improves the mechanical and flux pinning properties of ceramic superconductors. Thus, in this work, we show how we successfully obtained a polymeric precursor solution containing YBCO$+$Ag salts, which can be spun by the SBS route to produce ceramic samples. Yttrium, barium, copper, and silver metal acetates, and polyvinylpyrrolidone (PVP) (in a ratio of 5:1wt [PVP:acetates]) were dissolved in a solution with 61.5 wt\% of methanol, 12 wt\% of propionic acid, and 26.5 wt\% of ammonium hydroxide, together with 6 wt\% of PVP in solution. Three different amounts of silver (10 wt\%, 20 wt\%, and 30 wt\%) were used in YBa$_2$Cu$_3$O$_{7-x}$. The TGA characterizations revealed a lowering of crystallization and partial melting temperatures by about \SI{30}{\celsius}. SEM images show that after burning out the polymer, a fabric composed of nanowires of diameters up to \SI{380}{\nano \metre} is produced. However, after the sintering process at \SI{925}{\celsius} for \SI{1}{\hour}, the nanowires shrink into a porous-like sample.

  • Round Robin Test of Residual Resistance Ratio of Nb3Sn Composite Superconductors

    by Teruo Matsushita, Edmund Soji Otabe, Dong Ho Kim, Taejong Hwang, Huixian Gao, Fang Liu, Huajun Liu, Lance Cooley, Daniele Turrioni, Mark J. Raine, et al.

    Round robin test of residual resistance ratio (RRR) was performed for Nb3Sn composite superconductors prepared by internal tin method by six institutes with the international standard test method described in IEC 61788-4. It was found that uncertainty was mainly resulted from determination of the cryogenic resistance from the intersection of two straight lines drawn to fit the voltage vs. temperature curve around the resistive transition. The measurement clarified that RRR can be measured with expanded uncertainty not larger than 5% with the coverage factor 2 by using this test method.


  • Superconducting Properties of Titanium Alloys (Ti-64 and Ti-6242) for Critical Current Barrels

    by Francis J. Ridgeon, Mark J. Raine, D. P. Halliday, M'HAmed Lakrimi, Adrian Thomas, Damian P. Hampshire

    We have measured the superconducting properties of the titanium alloy Ti-6Al-4V (Ti-64) as supplied and following two of the heat treatment schedules used for the Nb3Sn strands in the ITER tokamak. The Ti-64 alloy is the standard choice in the superconducting community for the barrels used to make critical current (I C ) measurements in high magnetic fields at cryogenic temperatures. Ti-64, which has a two-phase alpha + beta microstructure and contains vanadium (n.b. T C (V) ~ 5.4 K), is superconducting at 4.2 K in fields up to 3 T. We have also measured Ti-6Al-2Sn-4Zr-2Mo-0.2Si (Ti-6242), which is in the near alpha phase and contains tin (n.b. T C (Sn) ~ 3.7 K). The critical temperature of Ti-6242 is 2.38 K, which is lower than the 5.12 K of Ti-64. Hence Ti-6242 is a better choice of barrel material for I C measurements required at 4.2 K in low fields up to 3 T, because it remains in the normal state.


  • Modeling and Comparison of In-Field Critical Current Density Anisotropy in High-Temperature Superconducting (HTS) Coated Conductors

    by Di Hu, Mark D. Ainslie, Mark J. Raine, Damian P. Hampshire, Jin Zou

    The development of high-temperature superconducting (HTS) wires is now at a stage where long lengths of high quality are commercially available, and of these, (Re)BCO coated conductors show the most promise for practical applications. One of the most crucial aspects of coil and device modeling is providing accurate data for the anisotropy of the critical current density J c (B, θ) of the superconductor. In this paper, the in-field critical current density characteristics J c (B, θ) of two commercial HTS coated conductor samples are experimentally measured, and based on these data, an engineering formula is introduced to represent this electromagnetic behavior as the input data for numerical modeling. However, due to the complex nature of this behavior and the large number of variables involved, the computational speed of the model can be extremely slow. Therefore, a two-variable direct interpolation method is introduced, which completely avoids any complex data fitting for J c (B, θ) and expresses the anisotropic behavior in the model directly and accurately with a significant improvement in computational speed. The two techniques are validated and compared using numerical models based on the H-formulation by calculating the self-field and in-field dc critical currents and the ac loss for a single coated conductor.


  • European Nb3Sn Superconducting Strand Production and Characterization for ITER TF Coil Conductor

    by T. Boutboul, V. Abaecherli, G. Berger, D. Hampshire, J. Parrell, M. Raine, P. Readman, B. Sailer, K. Schlenga, M. Thoener, et al.

    The European Union contributes around 20% of the cable-in-conduit conductor lengths needed for the ITER toroidal field (TF) magnet coils. For that purpose, 97 tons of Nb 3 Sn superconducting strand have been fabricated over five years, the production being completed in 2014. This superconducting strand has been manufactured by two companies, namely, Bruker EAS (Germany) and OST (USA), through the bronze route and the internal tin diffusion, respectively. This paper reports the outcomes of this strand mass production and of the strand characterization as performed by the suppliers and cross-checked on a regular basis by Durham University.