JLJianchao Li

Jianchao Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jianchao Li has a total of 5 co-authors. Here are the top co-authors by number of shared publications:

  • Ping Chen

    School of Mechanical Engineering University of Science and Technology Beijing Beijing China

    3 shared publications
  • Yuan Wang

    School of Mechanical Engineering University of Science and Technology Beijing Beijing China

    2 shared publications
  • Lifang Zheng

    School of Mechanical Engineering, University of Science and Technology Beijing, Beijing 100083, China

    1 shared publication
  • Weicheng Chu

    School of Mechanical Engineering University of Science and Technology Beijing Beijing China

    1 shared publication
  • Xiao‐Hua Sha

    School of Engineering and Technology China University of Geosciences (Beijing) Beijing 100083 China

    1 shared publication

Latest Publications

  • Synergetic effect of fly ash cenospheres and multi‐walled carbon nanotubes on mechanical and tribological properties of epoxy resin coatings

    by Ping Chen, Yuan Wang, Jianchao Li, Weicheng Chu

    The multiform wear of friction pair components is the main cause of marine equipment failure and epoxy resin (EP) coatings have been widely used in this field. Fly ash cenospheres (FACs) and multi‐walled carbon nanotubes (MWCNTs) were used to reinforce the tribological properties of EP coatings. The synergetic effects of FACs and MWCNTs on the mechanical and tribological properties of EP coatings were studied. Experimental results show that the tensile and flexural properties of FACs‐MWCNTs/EP composites are significantly reinforced. The tribological performance of EP composite coatings under seawater conditions is improved by the synergetic effect of FACs and MWCNTs, especially, the 10 wt.% FACs‐1 wt.% MWCNTs/EP coatings behave the most excellent tribological properties. It indicates that FACs can increase the hardness of EP coatings and provide a smoother surface for the water film formation, which decreases the friction coefficient and wear volume. MWCNTs can increase the elasticity modulus of EP, and act as a rope to prevent EP matrix and FACs from being desquamated.


  • Tribological and corrosion performance of epoxy resin composite coatings reinforced with graphene oxide and fly ash cenospheres

    by Jianchao Li, Ping Chen, Yuan Wang

    In this work, a novel graphene oxide (GO)‐fly ash cenospheres (FACs) hybrid fillers was introduced to improve the wear and corrosive resistance of epoxy resin (ER) composite coatings. The tribological behavior and the corrosion performance of three kinds of coatings (pure ER, GO/ER and GO‐FACs/ER coatings) were studied and the reinforced mechanisms of coatings filled by different fillers were analyzed. The friction coefficient and wear rate of the ER coatings were decreased with the addition of GO‐FACs hybrids. The scanning electron microscope images showed that the dispersibility and compatibility of GO‐FACs hybrids were effectively improved compared with that of GO sheet. The water contact angle examination indicated that the hydrophobicity of the GO‐FACs/ER coatings increased. The electrochemical impedance spectroscopy (EIS) results demonstrated that the GO‐FACs/ER coatings have better anticorrosion performance compared with the pure ER coatings and the GO/ER coatings. The hydrophobic surface and the well dispersed fillers constitute the dual barrier to resist the corrosion medium.


  • Microstructural and mechanical characteristics of graphene oxide‐fly ash cenosphere hybrid reinforced epoxy resin composites

    by Jian‐Chao Li, Li‐Fang Zheng, Xiao‐Hua Sha, Ping Chen

    An experimental investigation into the influence of incorporation of graphene oxide (GO) and fly ash cenospheres (FACs) on the mechanical properties of epoxy resin (EP) composites. Two fillers were studied: GO‐FAC hybrid and single GO. The GO‐FAC hybrid was synthesized using a solution blending method, and characterized by FTIR, XRD, and scanning electron microscope (SEM). The modified EP composite specimens were prepared by adding different contents of GO and GO‐FAC hybrid. The investigation showed that the FACs were successfully carried on the GO layer. The experimental data indicated that the addition of GO‐FAC hybrid effectively improved the tensile property and the wear resistance of the EP composites, superior to the addition of single GO samples. The best tensile properties and lowest wear rate of EP composites were obtained when the hybrid content was 0.5 wt %. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 47173.