Junhu Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Junhu Yang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Xiaohui Wang
School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China
3 shared publications - Baodui Chai
School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China
2 shared publications - Bingxiao Jiang
School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou, China
2 shared publications Xiaobang Bai
School of Energy and Power Engineering, , Lanzhou, China
2 shared publicationsXiaohui Wang
School of Energy and Power Engineering, , Lanzhou, China
2 shared publicationsC E Li
School of civil engineering, Lanzhou University of technology, GanSu, Lanzhou,730050, People's Republic of China
1 shared publication
Latest Publications
- Open Access
- 25 August 2023
- Published by Frontiers Media SA in Frontiers in Energy Research
- Vol. 11, 1220395
Numerical investigation on the blade load distribution in a pump as turbine
Pump as turbine plays an important role in modern industrial process. One of the major goals of turbine design and optimization is to maximize its efficiency. Therefore, it is of great importance to connect force with work in the analysis process. In the present study, the three-dimensional flow field of the pump as a hydraulic turbine has been investigated in the steady-state mode. The load distribution along three captured streamlines (i.e., the shroud, hub and middle streamline) on both the pressure and the suction surface is observed, and the relationship between the load distribution and the working capability is systematically analyzed. The results show that the load distribution on the pressure surface of the hydraulic turbine blade gradually transitions from the reverse “S” shape to the “S” shape in the process of increasing flow rate, while the load distribution on the suction surface keeps increasing with a concave trend. The main work area of the fluid medium on the hydraulic turbine impeller is in the middle section of the blade. As the flow rate increases, the loads on the blade depict a linear decreasing trend from the inlet to the outlet. The net load acting on the blade is distributed in a concave parabola profile along the radial position of the blade. Focusing on the inlet and middle section of the blade profile in the design or optimization process of the hydraulic turbines will be more useful. This study provides a new analysis method for the design or optimization of hydraulic turbine impellers.
- 25 August 2023
- Published by Frontiers Media SA in Frontiers in Energy Research
- Vol. 11, 1220395
Open AccessNumerical investigation on the blade load distribution in a pump as turbine
Pump as turbine plays an important role in modern industrial process. One of the major goals of turbine design and optimization is to maximize its efficiency. Therefore, it is of great importance to connect force with work in the analysis process. In the present study, the three-dimensional flow field of the pump as a hydraulic turbine has been investigated in the steady-state mode. The load distribution along three captured streamlines (i.e., the shroud, hub and middle streamline) on both the pressure and the suction surface is observed, and the relationship between the load distribution and the working capability is systematically analyzed. The results show that the load distribution on the pressure surface of the hydraulic turbine blade gradually transitions from the reverse “S” shape to the “S” shape in the process of increasing flow rate, while the load distribution on the suction surface keeps increasing with a concave trend. The main work area of the fluid medium on the hydraulic turbine impeller is in the middle section of the blade. As the flow rate increases, the loads on the blade depict a linear decreasing trend from the inlet to the outlet. The net load acting on the blade is distributed in a concave parabola profile along the radial position of the blade. Focusing on the inlet and middle section of the blade profile in the design or optimization process of the hydraulic turbines will be more useful. This study provides a new analysis method for the design or optimization of hydraulic turbine impellers.
- Open Access
Force Characteristics of Centrifugal Pump as Turbine during Start-Up Process under Gas–Liquid Two-Phase Conditions
The start-up process of a centrifugal pump as turbine (PAT) under gas–liquid two-phase conditions was simulated based on Fluent, and the evolution mechanism of the internal flow field and the variation law of force characteristics were studied in its start-up process under gas–liquid two-phase conditions. The results show that the area with high gas phase concentration corresponds to a strong vortex at the beginning of the start-up. The vortex intensity in the impeller gradually decreases with an increase in rotational speed. The gas volume fraction of the blade suction surface is more significant than that of the blade pressure surface. The higher the inlet gas volume fraction (IGVF) is, the more severely the blade load will fluctuate during the start-up process. As the rotational speed increases, the fluctuation of the blade load gradually weakens, and the maximum load is distributed near the inner edge of the blade after the rotational speed is stable. The periodic unbalanced radial force is produced in the start-up process. From the pure liquid conditions to the gas–liquid two-phase conditions with increasing IGVF, the dominant frequency amplitude of radial force shows a similar trend of decreasing first but then increasing. After the rotational speed tends to be stable, the dominant frequency of radial force is equal to the rotational frequency of the blade. With the increase in rotational speed, the dominant frequency amplitude of axial force decreases gradually. The higher the IGVF, the greater the dominant frequency amplitude of axial force at the same time.
Open AccessForce Characteristics of Centrifugal Pump as Turbine during Start-Up Process under Gas–Liquid Two-Phase Conditions
The start-up process of a centrifugal pump as turbine (PAT) under gas–liquid two-phase conditions was simulated based on Fluent, and the evolution mechanism of the internal flow field and the variation law of force characteristics were studied in its start-up process under gas–liquid two-phase conditions. The results show that the area with high gas phase concentration corresponds to a strong vortex at the beginning of the start-up. The vortex intensity in the impeller gradually decreases with an increase in rotational speed. The gas volume fraction of the blade suction surface is more significant than that of the blade pressure surface. The higher the inlet gas volume fraction (IGVF) is, the more severely the blade load will fluctuate during the start-up process. As the rotational speed increases, the fluctuation of the blade load gradually weakens, and the maximum load is distributed near the inner edge of the blade after the rotational speed is stable. The periodic unbalanced radial force is produced in the start-up process. From the pure liquid conditions to the gas–liquid two-phase conditions with increasing IGVF, the dominant frequency amplitude of radial force shows a similar trend of decreasing first but then increasing. After the rotational speed tends to be stable, the dominant frequency of radial force is equal to the rotational frequency of the blade. With the increase in rotational speed, the dominant frequency amplitude of axial force decreases gradually. The higher the IGVF, the greater the dominant frequency amplitude of axial force at the same time.
- Open Access
Pressure Fluctuation Characteristics Analysis of Centrifugal Pump as Turbine in Its Start-Up Process
In order to study pressure fluctuation characteristics of a centrifugal pump as turbine (PAT) in its start-up process, Fluent was used to do numerical simulation of the PAT start-up process. Time and frequency domain analyses were performed on the data acquired at different positions and different heads. The results show that a large number of low-pressure areas and strong vortexes are formed within the impeller at the initial time of start-up. With the increase in rotating speed, the vortexes rapidly decrease and are concentrated on the blade non-working face. The pressure fluctuation amplitude is the maximum at the start-up initial instant; with increase in rotating speed, it reduces rapidly at the volute spiral part. The pressure fluctuation number within one impeller rotation cycle is consistent with blade number, and the dominant frequency of pressure fluctuation is 6 times the impeller rotational frequency. The dominant frequency amplitude of radial pressure fluctuation increases with decrease in radial size in the volute. The pressure fluctuation in the impeller is much more intensive than that in the volute, and its maximum dominant frequency amplitude occurs in the middle of the impeller towards the inner edge. With the increase in head, the number of pressure fluctuation and the amplitude of dominant frequency increase at the same time during the start-up process.
Open AccessPressure Fluctuation Characteristics Analysis of Centrifugal Pump as Turbine in Its Start-Up Process
In order to study pressure fluctuation characteristics of a centrifugal pump as turbine (PAT) in its start-up process, Fluent was used to do numerical simulation of the PAT start-up process. Time and frequency domain analyses were performed on the data acquired at different positions and different heads. The results show that a large number of low-pressure areas and strong vortexes are formed within the impeller at the initial time of start-up. With the increase in rotating speed, the vortexes rapidly decrease and are concentrated on the blade non-working face. The pressure fluctuation amplitude is the maximum at the start-up initial instant; with increase in rotating speed, it reduces rapidly at the volute spiral part. The pressure fluctuation number within one impeller rotation cycle is consistent with blade number, and the dominant frequency of pressure fluctuation is 6 times the impeller rotational frequency. The dominant frequency amplitude of radial pressure fluctuation increases with decrease in radial size in the volute. The pressure fluctuation in the impeller is much more intensive than that in the volute, and its maximum dominant frequency amplitude occurs in the middle of the impeller towards the inner edge. With the increase in head, the number of pressure fluctuation and the amplitude of dominant frequency increase at the same time during the start-up process.
- Open Access
- 1 October 2021
- Published by SAGE Publications in Science Progress
- Vol. 104 (4)
Optimization of twisted blade of pump as turbine based on high dimensional surrogate model
In order to improve the operation efficiency of the twisted blade pump as turbine (PAT), a medium specific speed PAT was selected as the research object. The variables of the twisted blade plane blade profile were defined, the twisted blade was transformed into three plane blade profiles, and the blade profiles were parameterized by MATLAB 9.7 software. MATLAB 9.7, CFturbo 2020 and Fluent 19.2 were used to build the support vector machine-high dimensional model representation (SVM-HDMR) surrogate model function for efficiency optimization of PAT. Genetic algorithm was run on MATLAB 9.7 to optimize the surrogate model function, and the optimized blade profiles were fed back. The optimization results were verified by numerical simulation and experiment. The results show that the simulation efficiency of the PAT after optimization at the design operating point is 3.51% higher than the efficiency of the PAT before optimization, and the output power is increased by 5.3%. The test efficiency of the PAT after optimization at the design operating point is 3.4% higher than the efficiency of the PAT before optimization, and the output power is increased by 5.1%.
- 1 October 2021
- Published by SAGE Publications in Science Progress
- Vol. 104 (4)
Open AccessOptimization of twisted blade of pump as turbine based on high dimensional surrogate model
In order to improve the operation efficiency of the twisted blade pump as turbine (PAT), a medium specific speed PAT was selected as the research object. The variables of the twisted blade plane blade profile were defined, the twisted blade was transformed into three plane blade profiles, and the blade profiles were parameterized by MATLAB 9.7 software. MATLAB 9.7, CFturbo 2020 and Fluent 19.2 were used to build the support vector machine-high dimensional model representation (SVM-HDMR) surrogate model function for efficiency optimization of PAT. Genetic algorithm was run on MATLAB 9.7 to optimize the surrogate model function, and the optimized blade profiles were fed back. The optimization results were verified by numerical simulation and experiment. The results show that the simulation efficiency of the PAT after optimization at the design operating point is 3.51% higher than the efficiency of the PAT before optimization, and the output power is increased by 5.3%. The test efficiency of the PAT after optimization at the design operating point is 3.4% higher than the efficiency of the PAT before optimization, and the output power is increased by 5.1%.
- Open Access
Numerical Simulation of Axial Vortex in a Centrifugal Pump as Turbine with S-Blade Impeller
Pump as turbines (PATs) are widely applied for recovering the dissipated energy of high-pressure fluids in several hydraulic energy resources. When a centrifugal pump operates as turbine, the large axial vortex occurs usually within the impeller flow passages. In view of the structure and evolution of the vortex, and its effect on pressure fluctuation and energy conversion of the machine, a PAT with specific-speed 9.1 was analyzed based on detached eddy simulation (DES), and the results showed that vortices generated at the impeller inlet region, and the size and position of detected vortices, were fixed as the impeller rotated. However, the swirling strength of vortex cores changed periodically with double rotational frequency. The influence of vortices on pressure fluctuation of PAT was relatively obvious, deteriorating the operating stability of the machine evidently. In addition, the power loss near impeller inlet region was obviously heavy as the impact of large axial vortices, which was much more serious in low flow rate conditions. The results are helpful to realize the flow field of PAT and are instructive for blade optimization design.
Open AccessNumerical Simulation of Axial Vortex in a Centrifugal Pump as Turbine with S-Blade Impeller
Pump as turbines (PATs) are widely applied for recovering the dissipated energy of high-pressure fluids in several hydraulic energy resources. When a centrifugal pump operates as turbine, the large axial vortex occurs usually within the impeller flow passages. In view of the structure and evolution of the vortex, and its effect on pressure fluctuation and energy conversion of the machine, a PAT with specific-speed 9.1 was analyzed based on detached eddy simulation (DES), and the results showed that vortices generated at the impeller inlet region, and the size and position of detected vortices, were fixed as the impeller rotated. However, the swirling strength of vortex cores changed periodically with double rotational frequency. The influence of vortices on pressure fluctuation of PAT was relatively obvious, deteriorating the operating stability of the machine evidently. In addition, the power loss near impeller inlet region was obviously heavy as the impact of large axial vortices, which was much more serious in low flow rate conditions. The results are helpful to realize the flow field of PAT and are instructive for blade optimization design.
- Open Access
- 1 January 2019
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2019 (1)
Effect of Velocity Slip on Head Prediction for Centrifugal Pumps as Turbines
The application of pumps as turbines (PAT) has been developed in several applications for energy recovery schemes. Therefore, establishing a performance correlation between pump mode and turbine mode is essential for selecting the proper machine. However, slip phenomenon is the challenges of head prediction for PAT. In this paper, the slip phenomenon of pump and PAT was revealed, and the slip factor was studied using CFD. The effect of slip on head prediction for PAT was analyzed, and a theoretical prediction model was presented considering slip factors. In order to validate the head prediction model, six centrifugal pumps with specific speed (ns) from 9 to 54.8 were tested as turbines. Results showed that the predicted head by the proposed method was in good agreement with the experimental data, and it is more accurate than Stepanoff, Alatorre‐Frenk, Sharma, and Derakhshan models. This method can be applied in head prediction for low specific speed PAT ( ns <60).
- 1 January 2019
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2019 (1)
Open AccessEffect of Velocity Slip on Head Prediction for Centrifugal Pumps as Turbines
The application of pumps as turbines (PAT) has been developed in several applications for energy recovery schemes. Therefore, establishing a performance correlation between pump mode and turbine mode is essential for selecting the proper machine. However, slip phenomenon is the challenges of head prediction for PAT. In this paper, the slip phenomenon of pump and PAT was revealed, and the slip factor was studied using CFD. The effect of slip on head prediction for PAT was analyzed, and a theoretical prediction model was presented considering slip factors. In order to validate the head prediction model, six centrifugal pumps with specific speed (ns) from 9 to 54.8 were tested as turbines. Results showed that the predicted head by the proposed method was in good agreement with the experimental data, and it is more accurate than Stepanoff, Alatorre‐Frenk, Sharma, and Derakhshan models. This method can be applied in head prediction for low specific speed PAT ( ns <60).
- Open Access
- 10 June 2018
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 10 (6)
Analysis on the effect of variable guide vane numbers on the performance of pump as turbine
To study the effects of different guide vane numbers on the unsteady performance of pump as turbine based on the Navier–Stokes equation and standard k-epsilon turbulence model, computation fluid dynamics technology was used to simulate the flow field in pump as turbine. The turbulent kinetic energy, unsteady radial forces, and power losses were also clarified. The results show that for turbines with a guide vane, the distribution of turbulent kinetic energy is more uniform than before, and the radial force vector distribution is more symmetrical within four quadrants. The time-domain distribution of radial force is more periodic, the number of fluctuation periods is equal to the guide vane numbers, and the dominant frequency of the radial force is equal to the blade frequency. For different guide vane numbers, the effects on the unsteady performance of pump as turbine are different. When the guide vane number is equal to 9, the distribution of turbulence kinetic energy is optimal. In addition, at an optimal flow rate, both the time domains of the radial force and the power losses of the impeller are minimal, so to the geometric parameters of the hydraulic turbine are definite, the optimal guide vane number exists.
- 10 June 2018
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 10 (6)
Open AccessAnalysis on the effect of variable guide vane numbers on the performance of pump as turbine
To study the effects of different guide vane numbers on the unsteady performance of pump as turbine based on the Navier–Stokes equation and standard k-epsilon turbulence model, computation fluid dynamics technology was used to simulate the flow field in pump as turbine. The turbulent kinetic energy, unsteady radial forces, and power losses were also clarified. The results show that for turbines with a guide vane, the distribution of turbulent kinetic energy is more uniform than before, and the radial force vector distribution is more symmetrical within four quadrants. The time-domain distribution of radial force is more periodic, the number of fluctuation periods is equal to the guide vane numbers, and the dominant frequency of the radial force is equal to the blade frequency. For different guide vane numbers, the effects on the unsteady performance of pump as turbine are different. When the guide vane number is equal to 9, the distribution of turbulence kinetic energy is optimal. In addition, at an optimal flow rate, both the time domains of the radial force and the power losses of the impeller are minimal, so to the geometric parameters of the hydraulic turbine are definite, the optimal guide vane number exists.
- Open Access
- 20 December 2013
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 52 (5) , 052029
Numerical prediction for effects of guide vane blade numbers on hydraulic turbine performance
Using unstructured hybrid grid technique and SIMPLEC algorithm,a general three-dimensional simulation based on Reynolds Navier- stocks in multiple reference frames and the RNG k-ε turbulence model, is presented for the reversal centrifugal pump (PAT) with a guide vane. Four different schemes are designed by a change of the number of guide vane blade of PAT. The inner flow field in every scheme is simulated, accordingly, the external characteristic and static pressure distribution in flow field in PAT is obtained. The results obtained show that the efficiency can be improved by adding a guide vane for the PAT, besides, the high efficiency area is wider than before. Guide blade numbers changed, external characteristics of turbine changed, and the external characteristic changed. The optimal value is existent for the guide vane blade number, which has a great impact on the distribution of pressure in runner inlet.
- 20 December 2013
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 52 (5) , 052029
Open AccessNumerical prediction for effects of guide vane blade numbers on hydraulic turbine performance
Using unstructured hybrid grid technique and SIMPLEC algorithm,a general three-dimensional simulation based on Reynolds Navier- stocks in multiple reference frames and the RNG k-ε turbulence model, is presented for the reversal centrifugal pump (PAT) with a guide vane. Four different schemes are designed by a change of the number of guide vane blade of PAT. The inner flow field in every scheme is simulated, accordingly, the external characteristic and static pressure distribution in flow field in PAT is obtained. The results obtained show that the efficiency can be improved by adding a guide vane for the PAT, besides, the high efficiency area is wider than before. Guide blade numbers changed, external characteristics of turbine changed, and the external characteristic changed. The optimal value is existent for the guide vane blade number, which has a great impact on the distribution of pressure in runner inlet.