Alexander Schug
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Alexander Schug has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Dennis Rinker
Fraunhofer Research Institution for Casting, Composite and Processing Technology IGCV
1 shared publicationGabriel Kapphan
Fraunhofer Research Institution for Casting, Composite and Processing Technology IGCV, Am Technologiezentrum 2, 86159 Augsburg, Germany
1 shared publicationGeorg Bardl
Institute of Textile Machinery and High Performance Material Technology (ITM), TU Dresden, Dresden, Germany
1 shared publicationKlaus Drechsler
Fraunhofer Research Institution for Casting, Composite and Processing Technology IGCV
1 shared publication- Klaus Drechsler
Chair of Carbon Composites, Technical University of Munich, Boltzmannstr. 15, 85748 Garching, Germany
1 shared publication Roland Hinterhoelzl
Fraunhofer Research Institution for Casting, Composite and Processing Technology IGCV
1 shared publication
Latest Publications
- 2 April 2018
- Published by Springer Nature in International Journal of Material Forming
- Vol. 12 (2) , 279-293
Evaluating the potential of forming spot-welded layups out of fibre reinforced thermoplastic tape without previous consolidation
- 2 April 2018
- Published by Springer Nature in International Journal of Material Forming
- Vol. 12 (2) , 279-293
Evaluating the potential of forming spot-welded layups out of fibre reinforced thermoplastic tape without previous consolidation
- 1 January 2018
- Published by AIP Publishing
- Vol. 1960 (1) , 020028
Comparison of validation methods for forming simulations
The forming simulation of fibre reinforced thermoplastics could reduce the development time and improve the forming results. But to take advantage of the full potential of the simulations it has to be ensured that the predictions for material behaviour are correct. For that reason, a thorough validation of the material model has to be conducted after characterising the material. Relevant aspects for the validation of the simulation are for example the outer contour, the occurrence of defects and the fibre paths. To measure these features various methods are available. Most relevant and also most difficult to measure are the emerging fibre orientations. For that reason, the focus of this study was on measuring this feature. The aim was to give an overview of the properties of different measuring systems and select the most promising systems for a comparison survey. Selected were an optical, an eddy current and a computer-assisted tomography system with the focus on measuring the fibre orientations. Different formed 3D parts made of unidirectional glass fibre and carbon fibre reinforced thermoplastics were measured. Advantages and disadvantages of the tested systems were revealed. Optical measurement systems are easy to use, but are limited to the surface plies. With an eddy current system also lower plies can be measured, but it is only suitable for carbon fibres. Using a computer-assisted tomography system all plies can be measured, but the system is limited to small parts and challenging to evaluate.
- 1 January 2018
- Published by AIP Publishing
- Vol. 1960 (1) , 020028
Comparison of validation methods for forming simulations
The forming simulation of fibre reinforced thermoplastics could reduce the development time and improve the forming results. But to take advantage of the full potential of the simulations it has to be ensured that the predictions for material behaviour are correct. For that reason, a thorough validation of the material model has to be conducted after characterising the material. Relevant aspects for the validation of the simulation are for example the outer contour, the occurrence of defects and the fibre paths. To measure these features various methods are available. Most relevant and also most difficult to measure are the emerging fibre orientations. For that reason, the focus of this study was on measuring this feature. The aim was to give an overview of the properties of different measuring systems and select the most promising systems for a comparison survey. Selected were an optical, an eddy current and a computer-assisted tomography system with the focus on measuring the fibre orientations. Different formed 3D parts made of unidirectional glass fibre and carbon fibre reinforced thermoplastics were measured. Advantages and disadvantages of the tested systems were revealed. Optical measurement systems are easy to use, but are limited to the surface plies. With an eddy current system also lower plies can be measured, but it is only suitable for carbon fibres. Using a computer-assisted tomography system all plies can be measured, but the system is limited to small parts and challenging to evaluate.