Mohammad Sukri Mustapa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mohammad Sukri Mustapa has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Mohd Azhar Harimon
Universiti Tun Hussein Onn Malaysia
2 shared publications Muhammad Faizullah Pasha
2 shared publications- Satworo Adiwidodo
Politeknik Negeri Malang
2 shared publications - Abdullah Wagiman
University Tun Hussein Onn Malaysia
1 shared publication Ahmad Amirul Mukmin Yusof
Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor, Malaysia
1 shared publicationAiman Supawi
Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor, Malaysia
1 shared publication
Latest Publications
- Open Access
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Reliability Optimization Study of 18650 Lithium-Ion Batteries under Variable End-of-Discharge Voltage Using Weibull Analysis and the Taguchi Method
The long-term reliability of lithium-ion batteries is strongly influenced by operational parameters, particularly the allowable end-of-discharge voltage. This study investigates the reliability behavior of four commercial 18650 lithium-ion battery brands under four residual voltage levels (1.5 V, 1.7 V, 1.9 V, and 2.1 V) using experimental cycling data, Weibull lifetime analysis, and Taguchi-based optimization. Each cell was subjected to 60 charge–discharge cycles at a constant current of 2.5 A using a multi-channel battery analyzer. Time-to-failure data derived from discharge duration were used to estimate mean time between failures (MTBF) and reliability indices. Weibull analysis revealed distinct failure behaviors across brands, with selected cells exhibiting wear-dominated characteristics (β > 1), indicating suitability for operational optimization. Taguchi L16 design and larger-is-better signal-to-noise analysis identified battery brand as the dominant factor affecting reliability, while residual voltage exhibited a smaller but consistent influence. The optimal operating condition was achieved using the HONGLI cell at a residual voltage of 2.1 V. The findings demonstrate that appropriate voltage window management combined with cell selection plays a critical role in improving the operational reliability of lithium-ion batteries.
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessReliability Optimization Study of 18650 Lithium-Ion Batteries under Variable End-of-Discharge Voltage Using Weibull Analysis and the Taguchi Method
The long-term reliability of lithium-ion batteries is strongly influenced by operational parameters, particularly the allowable end-of-discharge voltage. This study investigates the reliability behavior of four commercial 18650 lithium-ion battery brands under four residual voltage levels (1.5 V, 1.7 V, 1.9 V, and 2.1 V) using experimental cycling data, Weibull lifetime analysis, and Taguchi-based optimization. Each cell was subjected to 60 charge–discharge cycles at a constant current of 2.5 A using a multi-channel battery analyzer. Time-to-failure data derived from discharge duration were used to estimate mean time between failures (MTBF) and reliability indices. Weibull analysis revealed distinct failure behaviors across brands, with selected cells exhibiting wear-dominated characteristics (β > 1), indicating suitability for operational optimization. Taguchi L16 design and larger-is-better signal-to-noise analysis identified battery brand as the dominant factor affecting reliability, while residual voltage exhibited a smaller but consistent influence. The optimal operating condition was achieved using the HONGLI cell at a residual voltage of 2.1 V. The findings demonstrate that appropriate voltage window management combined with cell selection plays a critical role in improving the operational reliability of lithium-ion batteries.
- Open Access
- 18 May 2026
- Published by Universitas PGRI Madiun in CHEESA: Chemical Engineering Research Articles
- Vol. 9 (1)
Potato Peel Starch Bioplastics Reinforced with Microcrystalline Cellulose, PVA, and Chitosan: Mechanical, Thermal, and Antibacterial Properties
The increasing accumulation of petroleum-based plastic waste has led to the development of biodegradable packaging materials from renewable agro-industrial resources. Therefore, this study aims to synthesize biodegradable potato peel starch/polyvinyl alcohol (PPS/PVA) blend bioplastic films reinforced with microcrystalline cellulose (MCC) and functionalized with chitosan. Films were prepared through solution casting with varied MCC contents and characterized for density, tensile properties, crystallinity, thermal stability, morphology, antibacterial activity, and biodegradability. The results showed that an increase in MCC improved film compactness, tensile strength, crystallinity, and surface uniformity, showing stronger interfacial interactions within the polymer matrix. FTIR confirmed enhanced hydrogen bonding among starch, PVA, chitosan, and MCC, while thermal analysis showed improved resistance to degradation. The produced films also exhibited antibacterial activity against Staphylococcus aureus and Escherichia coli, with the highest performance observed at higher MCC loading. Despite reinforcement, the products remained biodegradable in soil. These results show the potential of PPS/PVA blend bioplastic films containing PPS waste as sustainable materials for active packaging applications.
- 18 May 2026
- Published by Universitas PGRI Madiun in CHEESA: Chemical Engineering Research Articles
- Vol. 9 (1)
Open AccessPotato Peel Starch Bioplastics Reinforced with Microcrystalline Cellulose, PVA, and Chitosan: Mechanical, Thermal, and Antibacterial Properties
The increasing accumulation of petroleum-based plastic waste has led to the development of biodegradable packaging materials from renewable agro-industrial resources. Therefore, this study aims to synthesize biodegradable potato peel starch/polyvinyl alcohol (PPS/PVA) blend bioplastic films reinforced with microcrystalline cellulose (MCC) and functionalized with chitosan. Films were prepared through solution casting with varied MCC contents and characterized for density, tensile properties, crystallinity, thermal stability, morphology, antibacterial activity, and biodegradability. The results showed that an increase in MCC improved film compactness, tensile strength, crystallinity, and surface uniformity, showing stronger interfacial interactions within the polymer matrix. FTIR confirmed enhanced hydrogen bonding among starch, PVA, chitosan, and MCC, while thermal analysis showed improved resistance to degradation. The produced films also exhibited antibacterial activity against Staphylococcus aureus and Escherichia coli, with the highest performance observed at higher MCC loading. Despite reinforcement, the products remained biodegradable in soil. These results show the potential of PPS/PVA blend bioplastic films containing PPS waste as sustainable materials for active packaging applications.
- Open Access
- 15 July 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (2) , 413-424
Preparation and characterization of cellulose nanocrystals (CNCs) from pennisetum purpureum (PP) fibers via ammonium persulfate oxidation method
The growing demand for sustainable and high-performance materials emphasizes the need for more efficient production methods for cellulose nanocrystals (CNCs). Traditional CNC synthesis, however, often requires significant energy input and produces harmful by-products, which undermine its environmental and economic viability. In response to this challenge, this study explores the use of an eco-friendly ammonium persulfate (APS) oxidation method to produce CNCs from Pennisetum purpureum fibers. The findings reveal that CNCs synthesized at a temperature of 60 °C exhibited the highest crystallinity index (72.62%), optimal surface functionalization, and exceptional mechanical properties, including a tensile strength of 18.44 MPa.The structural, chemical, and mechanical properties of the CNCs were comprehensively evaluated using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDX), and tensile strength testing. These results highlight the effectiveness of APS oxidation in producing high-quality CNCs from readily available agricultural biomass. By utilizing a sustainable approach, this research not only advances the production of eco-friendly materials but also demonstrates the potential for agricultural waste to be repurposed in nanotechnology applications. The study thus makes a significant contribution to sustainable material science, providing insights into improving CNCs production while minimizing environmental impact, ultimately supporting the transition towards a more sustainable and circular economy.
- 15 July 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (2) , 413-424
Open AccessPreparation and characterization of cellulose nanocrystals (CNCs) from pennisetum purpureum (PP) fibers via ammonium persulfate oxidation method
The growing demand for sustainable and high-performance materials emphasizes the need for more efficient production methods for cellulose nanocrystals (CNCs). Traditional CNC synthesis, however, often requires significant energy input and produces harmful by-products, which undermine its environmental and economic viability. In response to this challenge, this study explores the use of an eco-friendly ammonium persulfate (APS) oxidation method to produce CNCs from Pennisetum purpureum fibers. The findings reveal that CNCs synthesized at a temperature of 60 °C exhibited the highest crystallinity index (72.62%), optimal surface functionalization, and exceptional mechanical properties, including a tensile strength of 18.44 MPa.The structural, chemical, and mechanical properties of the CNCs were comprehensively evaluated using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDX), and tensile strength testing. These results highlight the effectiveness of APS oxidation in producing high-quality CNCs from readily available agricultural biomass. By utilizing a sustainable approach, this research not only advances the production of eco-friendly materials but also demonstrates the potential for agricultural waste to be repurposed in nanotechnology applications. The study thus makes a significant contribution to sustainable material science, providing insights into improving CNCs production while minimizing environmental impact, ultimately supporting the transition towards a more sustainable and circular economy.
- Open Access
- 27 February 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (8 (133)) , 35-45
Optimization design of wind turbine propeller using PVC pipe material with elbow tip accessories
PVC or Polyvinyl Chloride is a thermoplastic polymer, cheap, and can be used to make pipes and fittings. PVC pipes can be used to make low-power wind turbine blades. PVC pipes have good mechanical properties, including impact strength, high flexibility, vibration resistance, and hydrostatic pressure. To modify the pipe into a wind turbine blade that is strong against loads and has torsional resistance, an efficient design and manufacturing method is needed. In the blade design, an aerodynamic analysis is also carried out to obtain maximum energy from the wind turbine which is the result of the blade design performance. The goal is to find a way to build a turbine blade using PVC pipe and the best aerodynamic behavior of the fluid around the turbine rotor. This research is based on the CFD simulation method and experimental studies using a wind tunnel. Based on the results of the ANSYS CFD simulation at the elbow end of the PVC pipe turbine blade with an angle of attack of 15° and 30°, it can increase the torque by about 200 % compared to without the elbow end. CFD simulation was conducted to test the load on the PVC pipe blade with wind speeds of 5 m/s, 6 m/s, and 7 m/s, and angle tip widths of 100 mm, 110 mm, and 130 mm. The torque generated by the turbine is influenced by the width of the elbow tip, where the maximum torque is achieved by an elbow tip width of 110 mm. Based on the optimization results, the turbine can produce the best torque performance with the lowest stress generated from the load. The results of the von Mises stress analysis show that the stress that occurs on the turbine blade is the lowest, making it the safest and most reliable design. The results of the torque analysis show that the addition of an elbow tip can increase the torque on the turbine blade
- 27 February 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (8 (133)) , 35-45
Open AccessOptimization design of wind turbine propeller using PVC pipe material with elbow tip accessories
PVC or Polyvinyl Chloride is a thermoplastic polymer, cheap, and can be used to make pipes and fittings. PVC pipes can be used to make low-power wind turbine blades. PVC pipes have good mechanical properties, including impact strength, high flexibility, vibration resistance, and hydrostatic pressure. To modify the pipe into a wind turbine blade that is strong against loads and has torsional resistance, an efficient design and manufacturing method is needed. In the blade design, an aerodynamic analysis is also carried out to obtain maximum energy from the wind turbine which is the result of the blade design performance. The goal is to find a way to build a turbine blade using PVC pipe and the best aerodynamic behavior of the fluid around the turbine rotor. This research is based on the CFD simulation method and experimental studies using a wind tunnel. Based on the results of the ANSYS CFD simulation at the elbow end of the PVC pipe turbine blade with an angle of attack of 15° and 30°, it can increase the torque by about 200 % compared to without the elbow end. CFD simulation was conducted to test the load on the PVC pipe blade with wind speeds of 5 m/s, 6 m/s, and 7 m/s, and angle tip widths of 100 mm, 110 mm, and 130 mm. The torque generated by the turbine is influenced by the width of the elbow tip, where the maximum torque is achieved by an elbow tip width of 110 mm. Based on the optimization results, the turbine can produce the best torque performance with the lowest stress generated from the load. The results of the von Mises stress analysis show that the stress that occurs on the turbine blade is the lowest, making it the safest and most reliable design. The results of the torque analysis show that the addition of an elbow tip can increase the torque on the turbine blade
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2530 (1)
The effect on composition of peat soil as reinforcement on AA6061 aluminium chip to hardness and physical properties of metal matrix composite
The reinforcement materials on aluminium metal matrix composites are commonly used in the industrial sector due to their light-weight, improved fracture toughness, superior strength-to-weight ratio, and improved mechanical properties. This study investigates the effect on composition of peat soil as reinforcement on AA6061 aluminium chip to hardness and physical properties of metal matrix composite. AA6061 aluminium chip reinforced with peat soil at various composition prepared by using cold compaction technique were investigated. Due to the lower operating cost and energy consumption compared to conventional recycling by casting, this method was applied to study the hardness and physical properties of metal matrix composite samples. As a result, the addition of composition of peat soil shows improvement in term hardness and physical properties for composite compared to unreinforced AA6061 aluminium chip. The hardness of AA6061 aluminium chip has enhanced with increasing the composition of peat soil from 45.2826 Hv to 52.3120 Hv at an addition of 2.5 wt.%. The highest hardness shows with an addition of peat soil at 10 wt.% at 65.1069 Hv, however the porosity results shows that the samples have higher pores due to the larger amount of composition added. The physical properties on density of metal matrix composites samples shows the increment up to 5 wt.% of peat soils, and then decreased at increasing mass fraction of peat soil. The addition of peat soil at 7.5 wt.% as reinforcement material shows the improvement of hardness with light-weight on metal matrix composite samples.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2530 (1)
Open AccessThe effect on composition of peat soil as reinforcement on AA6061 aluminium chip to hardness and physical properties of metal matrix composite
The reinforcement materials on aluminium metal matrix composites are commonly used in the industrial sector due to their light-weight, improved fracture toughness, superior strength-to-weight ratio, and improved mechanical properties. This study investigates the effect on composition of peat soil as reinforcement on AA6061 aluminium chip to hardness and physical properties of metal matrix composite. AA6061 aluminium chip reinforced with peat soil at various composition prepared by using cold compaction technique were investigated. Due to the lower operating cost and energy consumption compared to conventional recycling by casting, this method was applied to study the hardness and physical properties of metal matrix composite samples. As a result, the addition of composition of peat soil shows improvement in term hardness and physical properties for composite compared to unreinforced AA6061 aluminium chip. The hardness of AA6061 aluminium chip has enhanced with increasing the composition of peat soil from 45.2826 Hv to 52.3120 Hv at an addition of 2.5 wt.%. The highest hardness shows with an addition of peat soil at 10 wt.% at 65.1069 Hv, however the porosity results shows that the samples have higher pores due to the larger amount of composition added. The physical properties on density of metal matrix composites samples shows the increment up to 5 wt.% of peat soils, and then decreased at increasing mass fraction of peat soil. The addition of peat soil at 7.5 wt.% as reinforcement material shows the improvement of hardness with light-weight on metal matrix composite samples.
- Open Access
- 26 September 2021
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 87 (2) , 137-144
Effect of Thermally Formed Alumina on Density of AlMgSi Alloys Extrudate Recycled Via Solid State Technique
Solid state recycling of aluminium via hot extrusion is a sustainable technique. The process performed before hot extrusion plays a vital role on the extrudate properties. In this study, the effect of naturally and thermally formed in-situ alumina on the extrudate density were investigated. Fours type of material identified as a solid as-received, non-treated recycle chip, 300 0C thermally treated recycle chip and 500 0C thermally treated recycle chip were prepared for the experiment. Prior to extrusion, the recycle chips were compacted into a chip-based billet, preheated and immediately extruded into a semi-finished product. The density test performed on the chip-based extrudate found that the type of chips influenced the density. The chip-based extrudate made of 300 0C and 500 0C thermally treated chips resulted in higher density than solid as-received and non-treated chips. Chip-based extrudate produced from 500 0C thermally treated chips resulted in density of 2724 kg/m3, which is the highest among the specimen. This density value was 0.7 % higher compared to the solid as-received extrudate. Microstructure examination on the cross-section revealed the alumina entrapped in the chip-based extrudate. The alumina entrapped in 500 0C thermally treated chips specimen was more prone than the non-treated and 300 0C thermally-treated chips. This finding explains the variation in the extrudate density.
- 26 September 2021
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 87 (2) , 137-144
Open AccessEffect of Thermally Formed Alumina on Density of AlMgSi Alloys Extrudate Recycled Via Solid State Technique
Solid state recycling of aluminium via hot extrusion is a sustainable technique. The process performed before hot extrusion plays a vital role on the extrudate properties. In this study, the effect of naturally and thermally formed in-situ alumina on the extrudate density were investigated. Fours type of material identified as a solid as-received, non-treated recycle chip, 300 0C thermally treated recycle chip and 500 0C thermally treated recycle chip were prepared for the experiment. Prior to extrusion, the recycle chips were compacted into a chip-based billet, preheated and immediately extruded into a semi-finished product. The density test performed on the chip-based extrudate found that the type of chips influenced the density. The chip-based extrudate made of 300 0C and 500 0C thermally treated chips resulted in higher density than solid as-received and non-treated chips. Chip-based extrudate produced from 500 0C thermally treated chips resulted in density of 2724 kg/m3, which is the highest among the specimen. This density value was 0.7 % higher compared to the solid as-received extrudate. Microstructure examination on the cross-section revealed the alumina entrapped in the chip-based extrudate. The alumina entrapped in 500 0C thermally treated chips specimen was more prone than the non-treated and 300 0C thermally-treated chips. This finding explains the variation in the extrudate density.
- Open Access
- 6 January 2020
- Published by Universitas Muhammadiyah Kalimantan Timur in JSE Journal of Science and Engineering
- Vol. 1 (1) , 25-29
Mechanical Behavior and Microstructural Analysis of Molybdenum-TZM Alloy Subjected to Different Annealing Temperature
Mo-TZM alloy is one of the most famous economic molybdenum-based alloys. The percentage of chemical composition in mass of Mo-TZM alloy are Mo-0.5Ti-0.08Zr-0.03C. By adding some Titanium and Zirconium so that the mechanical properties and recrystallization temperature of molybdenum has been corresponding improvement. The purpose of this study is to determine the effect of different annealing temperature on mechanical properties of Mo-TZM alloy. The samples will be heated at two different temperature which are 1000 oC and 1300 oC in 1 hour and 40 minutes to change their microstructure behavior. The mechanical properties of the sample like hardness will be analyzed by using Vickers Micro hardness test. The force applied is 4.903 N and Vickers micro hardness number is 0.5 HVN for 10 second. Then to observe the microstructure changes, optical microscope and Scanning Electron Microscope (SEM) is be used. At annealing temperature 1000 oC, it show values of hardness is 249.54 VHN and the grain boundary size is 0.0898mm. While at annealing temperature 1300 oC, it show the lowest values of hardness which is 243.55 VHN and the highest grain boundary size which is 0.1068 mm. By doing annealing heat treatment it will decreases hardness values and increases the size of grain boundary
- 6 January 2020
- Published by Universitas Muhammadiyah Kalimantan Timur in JSE Journal of Science and Engineering
- Vol. 1 (1) , 25-29
Open AccessMechanical Behavior and Microstructural Analysis of Molybdenum-TZM Alloy Subjected to Different Annealing Temperature
Mo-TZM alloy is one of the most famous economic molybdenum-based alloys. The percentage of chemical composition in mass of Mo-TZM alloy are Mo-0.5Ti-0.08Zr-0.03C. By adding some Titanium and Zirconium so that the mechanical properties and recrystallization temperature of molybdenum has been corresponding improvement. The purpose of this study is to determine the effect of different annealing temperature on mechanical properties of Mo-TZM alloy. The samples will be heated at two different temperature which are 1000 oC and 1300 oC in 1 hour and 40 minutes to change their microstructure behavior. The mechanical properties of the sample like hardness will be analyzed by using Vickers Micro hardness test. The force applied is 4.903 N and Vickers micro hardness number is 0.5 HVN for 10 second. Then to observe the microstructure changes, optical microscope and Scanning Electron Microscope (SEM) is be used. At annealing temperature 1000 oC, it show values of hardness is 249.54 VHN and the grain boundary size is 0.0898mm. While at annealing temperature 1300 oC, it show the lowest values of hardness which is 243.55 VHN and the highest grain boundary size which is 0.1068 mm. By doing annealing heat treatment it will decreases hardness values and increases the size of grain boundary