Mohd Azhar Harimon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohd Azhar Harimon has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Abdul Latif Mohd Tobi
Universiti Tun Hussein Onn Malaysia
3 shared publications- Abdullah Aziz Saad
School of Mechanical Engineering, Universiti Sains Malaysia, Nibong Tebal, Malaysia
3 shared publications - Mohammad Sukri Mustapa
Universiti Tun Hussein Onn Malaysia
2 shared publications Shinichi Yamamoto
2 shared publicationsYoshiharu Mutoh
2 shared publicationsYuichi Otsuka
2 shared publications
Latest Publications
- Open Access
- 6 January 2020
- Published by Universitas Muhammadiyah Kalimantan Timur in JSE Journal of Science and Engineering
- Vol. 1 (1) , 25-29
Mechanical Behavior and Microstructural Analysis of Molybdenum-TZM Alloy Subjected to Different Annealing Temperature
Mo-TZM alloy is one of the most famous economic molybdenum-based alloys. The percentage of chemical composition in mass of Mo-TZM alloy are Mo-0.5Ti-0.08Zr-0.03C. By adding some Titanium and Zirconium so that the mechanical properties and recrystallization temperature of molybdenum has been corresponding improvement. The purpose of this study is to determine the effect of different annealing temperature on mechanical properties of Mo-TZM alloy. The samples will be heated at two different temperature which are 1000 oC and 1300 oC in 1 hour and 40 minutes to change their microstructure behavior. The mechanical properties of the sample like hardness will be analyzed by using Vickers Micro hardness test. The force applied is 4.903 N and Vickers micro hardness number is 0.5 HVN for 10 second. Then to observe the microstructure changes, optical microscope and Scanning Electron Microscope (SEM) is be used. At annealing temperature 1000 oC, it show values of hardness is 249.54 VHN and the grain boundary size is 0.0898mm. While at annealing temperature 1300 oC, it show the lowest values of hardness which is 243.55 VHN and the highest grain boundary size which is 0.1068 mm. By doing annealing heat treatment it will decreases hardness values and increases the size of grain boundary
- 6 January 2020
- Published by Universitas Muhammadiyah Kalimantan Timur in JSE Journal of Science and Engineering
- Vol. 1 (1) , 25-29
Open AccessMechanical Behavior and Microstructural Analysis of Molybdenum-TZM Alloy Subjected to Different Annealing Temperature
Mo-TZM alloy is one of the most famous economic molybdenum-based alloys. The percentage of chemical composition in mass of Mo-TZM alloy are Mo-0.5Ti-0.08Zr-0.03C. By adding some Titanium and Zirconium so that the mechanical properties and recrystallization temperature of molybdenum has been corresponding improvement. The purpose of this study is to determine the effect of different annealing temperature on mechanical properties of Mo-TZM alloy. The samples will be heated at two different temperature which are 1000 oC and 1300 oC in 1 hour and 40 minutes to change their microstructure behavior. The mechanical properties of the sample like hardness will be analyzed by using Vickers Micro hardness test. The force applied is 4.903 N and Vickers micro hardness number is 0.5 HVN for 10 second. Then to observe the microstructure changes, optical microscope and Scanning Electron Microscope (SEM) is be used. At annealing temperature 1000 oC, it show values of hardness is 249.54 VHN and the grain boundary size is 0.0898mm. While at annealing temperature 1300 oC, it show the lowest values of hardness which is 243.55 VHN and the highest grain boundary size which is 0.1068 mm. By doing annealing heat treatment it will decreases hardness values and increases the size of grain boundary
- 17 June 2019
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 50 (6) , 718-723
Effect of hot extrusion parameters on microhardness and microstructure in direct recycling of aluminium chips
Direct hot extrusion is an alternative process for recycling aluminium without melting the scrap. It utilizes low energy and is environmental friendly. This paper reports the microhardness and microstructure of aluminium alloy chips when subjected to various settings of preheating temperature and preheating time in hot extrusion process. Three values of preheating temperature are taken as 450 °C, 500 °C, and 550 °C. On the other hand, three values of preheating time were chosen (1 h, 2 h, 3 h). The influences of the process parameters (preheating temperature and time) are analyzed using design of experiments approach whereby full factorial design with center point analysis are adopted. The total runs are 11 and they comprise of two factors of full factorial design with 3 center points. The responses are microhardness and microstructure. The results show that microhardness increases with the decrease of the preheating temperature. The results also show that the preheating temperature is more important to be controlled rather than the preheating time in microhardness analyses. The profile extrudes at 450 °C and 1 hour has gained the optimum microhardness and it can be concluded that setting temperature at 550 °C for 3 hours results in the highest responses for average grain sizes in analysis of microstructure.
- 17 June 2019
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 50 (6) , 718-723
Effect of hot extrusion parameters on microhardness and microstructure in direct recycling of aluminium chips
Direct hot extrusion is an alternative process for recycling aluminium without melting the scrap. It utilizes low energy and is environmental friendly. This paper reports the microhardness and microstructure of aluminium alloy chips when subjected to various settings of preheating temperature and preheating time in hot extrusion process. Three values of preheating temperature are taken as 450 °C, 500 °C, and 550 °C. On the other hand, three values of preheating time were chosen (1 h, 2 h, 3 h). The influences of the process parameters (preheating temperature and time) are analyzed using design of experiments approach whereby full factorial design with center point analysis are adopted. The total runs are 11 and they comprise of two factors of full factorial design with 3 center points. The responses are microhardness and microstructure. The results show that microhardness increases with the decrease of the preheating temperature. The results also show that the preheating temperature is more important to be controlled rather than the preheating time in microhardness analyses. The profile extrudes at 450 °C and 1 hour has gained the optimum microhardness and it can be concluded that setting temperature at 550 °C for 3 hours results in the highest responses for average grain sizes in analysis of microstructure.
- 1 January 2018
- Published by Elsevier in Materials & Design
- Vol. 137, 335-344
High temperature fatigue characteristics of P/M and hot-forged W-Re and TZM for X-ray target of CT scanner
- 1 January 2018
- Published by Elsevier in Materials & Design
- Vol. 137, 335-344
High temperature fatigue characteristics of P/M and hot-forged W-Re and TZM for X-ray target of CT scanner
- 1 August 2017
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 66, 52-56
High temperature fracture toughness of TZM alloys with different kinds of grain boundary particles
- 1 August 2017
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 66, 52-56
High temperature fracture toughness of TZM alloys with different kinds of grain boundary particles
- 1 August 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 372, 522-527
Investigation on the Interaction between Plasticity Response and Fretting Wear under Gross Sliding Condition
The fretting wear behavior of Ti-6Al-4V is studied with the focus on cyclic plasticity effect under gross sliding condition. The analysis is simulated using finite element based method with a new surface profile model represently a given number of cycles using a cylinder-on-flat geometry. The effect of cyclic plasticity on the stresses and plastic strain distribution is studied. The maximum tangential stress is predicted at the trailing edge while the maximum compressive tangential stress is predicted at the leading edge of contact area. Plasticity in shear component is significant compare to tangential component and predicted at 0th and 3000th cycles only. It is found that important to include plasticity that remains from previous cycle for better prediction of fretting wear.
- 1 August 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 372, 522-527
Investigation on the Interaction between Plasticity Response and Fretting Wear under Gross Sliding Condition
The fretting wear behavior of Ti-6Al-4V is studied with the focus on cyclic plasticity effect under gross sliding condition. The analysis is simulated using finite element based method with a new surface profile model represently a given number of cycles using a cylinder-on-flat geometry. The effect of cyclic plasticity on the stresses and plastic strain distribution is studied. The maximum tangential stress is predicted at the trailing edge while the maximum compressive tangential stress is predicted at the leading edge of contact area. Plasticity in shear component is significant compare to tangential component and predicted at 0th and 3000th cycles only. It is found that important to include plasticity that remains from previous cycle for better prediction of fretting wear.
- 1 August 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 372, 516-521
Fretting Wear of Coated Substrate with Interlayer: Substrate Stress Behaviour
Finite element analysis of a coated SCMV (high-strength alloy steel) substrate with interlayer has been studied with the emphasized of stresses behaviour predicted in the substrate region due to the fretting wear surface profiles modification. The analysis is simulated using a simple cylinder-on-flat contact geometry under gross sliding condition for a given surface profile on a specific number of fretting cycles. The effect of interlayer stiffness on the stresses predicted in the substrate region is studied. It is found that the stresses in the substrate region are generally predicted to reduce with the increase of interlayer stiffness and with the advancement of wear.
- 1 August 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 372, 516-521
Fretting Wear of Coated Substrate with Interlayer: Substrate Stress Behaviour
Finite element analysis of a coated SCMV (high-strength alloy steel) substrate with interlayer has been studied with the emphasized of stresses behaviour predicted in the substrate region due to the fretting wear surface profiles modification. The analysis is simulated using a simple cylinder-on-flat contact geometry under gross sliding condition for a given surface profile on a specific number of fretting cycles. The effect of interlayer stiffness on the stresses predicted in the substrate region is studied. It is found that the stresses in the substrate region are generally predicted to reduce with the increase of interlayer stiffness and with the advancement of wear.
- 10 April 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 315, 909-913
Investigation on the Fretting Wear of a Coated Substrate with Interlayer
The fretting wear of coated SCMV (high-strength alloy steel) substrate with interlayer is studied with the focus on stresses associated with the coating failure under gross sliding condition. The analysis is simulated using finite element based method for a given number of cycles of worn half cylinder-on-flat geometry. The effect of interlayer stiffness on the stress distributions in the coating is studied. The maximum tensile stress at the trailing edge and the maximum compressive stress at the leading edge are reducing with increasing interlayer stiffness. The maximum shear stress at the coating-interlayer interface is predicted to have negligible effect with the change of interlayer stiffness. All the stresses are generally predicted to reduce with cycle. In general, stiffer interlayer will reduce the risk of coating failure.
- 10 April 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 315, 909-913
Investigation on the Fretting Wear of a Coated Substrate with Interlayer
The fretting wear of coated SCMV (high-strength alloy steel) substrate with interlayer is studied with the focus on stresses associated with the coating failure under gross sliding condition. The analysis is simulated using finite element based method for a given number of cycles of worn half cylinder-on-flat geometry. The effect of interlayer stiffness on the stress distributions in the coating is studied. The maximum tensile stress at the trailing edge and the maximum compressive stress at the leading edge are reducing with increasing interlayer stiffness. The maximum shear stress at the coating-interlayer interface is predicted to have negligible effect with the change of interlayer stiffness. All the stresses are generally predicted to reduce with cycle. In general, stiffer interlayer will reduce the risk of coating failure.