Dmitriy A. Yagodnikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dmitriy A. Yagodnikov has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
A. P. Shpara
Bauman Moscow State Technical University, Moscow, Russia
5 shared publicationsA. V. Sukhov
Bauman Moscow State Technical University, Moscow, Russia
5 shared publicationsA. O. Novikov
Bauman Moscow State Technical University, Moscow, Russia
2 shared publications- Alexey Borisovich Pnev
Scientific Education Center Photonics and IR Techniques, Bauman Moscow State Technical University, Moscow 105005, Russia
2 shared publications - Andrey A. Zhirnov
Laser and Optoelectronic Systems Department, Radio Electronics and Laser Technology Faculty, Bauman Moscow State Technical University, 2-nd Baumanskaya 5-1, 105005 Moscow, Russia
2 shared publications - Konstantin V. Stepanov
Laser and Optoelectronic Systems Department, Radio Electronics and Laser Technology Faculty, Bauman Moscow State Technical University, 2-nd Baumanskaya 5-1, 105005 Moscow, Russia
2 shared publications
Latest Publications
- 1 October 2025
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 61 (5) , 711-717
An Experimental Microwave Study of the Effect of Oxidant Particle Size on the Combustion Speed of an Energetic Condensed System at High Pressure
The effect of the particle size of oxidant (potassium nitrate) powder on the combustion behavior of a model energetic condensed system has been assessed experimentally by a noncontact microwave method in the pressure range 0.5–40 MPa. We have studied a model composition based on epoxy resin as a combustible binding agent, potassium nitrate, and ferric oxide (Fe2O3) as a combustion modifier. In evaluating the experimental linear combustion speed, random errors have been taken into account. Fitting the data with power law and linear functions, we have obtained analytical relations for the linear combustion speed of model energetic condensed systems as a function of pressure. The results demonstrate that, as the particle size of the oxidant powder decreases, the pressure at which the behavior of the combustion speed changes from a power law to linear also decreases, which is accompanied by an increase in combustion speed.
- 1 October 2025
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 61 (5) , 711-717
An Experimental Microwave Study of the Effect of Oxidant Particle Size on the Combustion Speed of an Energetic Condensed System at High Pressure
The effect of the particle size of oxidant (potassium nitrate) powder on the combustion behavior of a model energetic condensed system has been assessed experimentally by a noncontact microwave method in the pressure range 0.5–40 MPa. We have studied a model composition based on epoxy resin as a combustible binding agent, potassium nitrate, and ferric oxide (Fe2O3) as a combustion modifier. In evaluating the experimental linear combustion speed, random errors have been taken into account. Fitting the data with power law and linear functions, we have obtained analytical relations for the linear combustion speed of model energetic condensed systems as a function of pressure. The results demonstrate that, as the particle size of the oxidant powder decreases, the pressure at which the behavior of the combustion speed changes from a power law to linear also decreases, which is accompanied by an increase in combustion speed.
- 1 April 2025
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 61 (2) , 200-205
X-Ray Radiography Study of the Interior Ballistics of a Model Solid Rocket Motor
A contactless X-ray radiography technique for diagnostics of solid rocket motors (SRMs) is presented. An experimental study was performed to visualize intrachamber processes and determine the solid propellant burning rate in a model E-5-0 SRM using an X-ray system consisting of an X-ray source and a dynamic X-ray detector which are located at a given distance from the test object. The possibility of contactless determination of the propellant burning rate based on an analysis of gray level changes near the burning surface was confirmed experimentally. Radiography results are in satisfactory agreement with the results of other methods for determining the solid propellant burning rate.
- 1 April 2025
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 61 (2) , 200-205
X-Ray Radiography Study of the Interior Ballistics of a Model Solid Rocket Motor
A contactless X-ray radiography technique for diagnostics of solid rocket motors (SRMs) is presented. An experimental study was performed to visualize intrachamber processes and determine the solid propellant burning rate in a model E-5-0 SRM using an X-ray system consisting of an X-ray source and a dynamic X-ray detector which are located at a given distance from the test object. The possibility of contactless determination of the propellant burning rate based on an analysis of gray level changes near the burning surface was confirmed experimentally. Radiography results are in satisfactory agreement with the results of other methods for determining the solid propellant burning rate.
- 1 April 2024
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 60 (2) , 178-184
Effect of Heat Losses on Boron Particle Combustion in Air
This paper presents an analytical analysis of the effect of heat losses on the possibility of occurrence of the most effective gas-phase combustion of a single boron particle in air at different initial temperatures and pressures of the oxidizing medium. The analysis is performed with account for the possibility that the particle enters into an air medium (its temperature is lower than the melting point of boron) after its ignition and the establishment of a steady gas-phase combustion. A method for calculating the maximum initial air temperature below which a burning boron particle cools down and extinguishes is developed. The boundaries of the regions of its gas-phase combustion and extinguishing are determined. It has been established that when a single boron particle in a state of gas-phase combustion enters air with a temperature below the melting point, the main factor determining the its combustion mechanism is the air temperature. Depending on the air temperature, either the gas-phase combustion of the particle continues or the particle cools down and the gas-phase combustion changes to heterogeneous combustion.
- 1 April 2024
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 60 (2) , 178-184
Effect of Heat Losses on Boron Particle Combustion in Air
This paper presents an analytical analysis of the effect of heat losses on the possibility of occurrence of the most effective gas-phase combustion of a single boron particle in air at different initial temperatures and pressures of the oxidizing medium. The analysis is performed with account for the possibility that the particle enters into an air medium (its temperature is lower than the melting point of boron) after its ignition and the establishment of a steady gas-phase combustion. A method for calculating the maximum initial air temperature below which a burning boron particle cools down and extinguishes is developed. The boundaries of the regions of its gas-phase combustion and extinguishing are determined. It has been established that when a single boron particle in a state of gas-phase combustion enters air with a temperature below the melting point, the main factor determining the its combustion mechanism is the air temperature. Depending on the air temperature, either the gas-phase combustion of the particle continues or the particle cools down and the gas-phase combustion changes to heterogeneous combustion.
- 1 October 2022
- Published by Pleiades Publishing Ltd in High Temperature
- Vol. 60 (5) , 710-715
Experimental Investigation of Soot Formation Processes during Combustion of an Overenriched Oxygen–Methane Mixture
The article describes the experimental equipment, measurement and recording systems, and methods for conducting experimental studies of the features of soot formation during combustion of an overenriched oxygen–methane mixture in a two-zone model gas generator with a ratio of component contents in the range of 0.4–1.0. Using visualization of the in-chamber process in the second zone of a gas generator with digital color video filming and photoresistance recording of the radiation intensity of the combustion products, the conditions under which soot formation occurs are determined.
- 1 October 2022
- Published by Pleiades Publishing Ltd in High Temperature
- Vol. 60 (5) , 710-715
Experimental Investigation of Soot Formation Processes during Combustion of an Overenriched Oxygen–Methane Mixture
The article describes the experimental equipment, measurement and recording systems, and methods for conducting experimental studies of the features of soot formation during combustion of an overenriched oxygen–methane mixture in a two-zone model gas generator with a ratio of component contents in the range of 0.4–1.0. Using visualization of the in-chamber process in the second zone of a gas generator with digital color video filming and photoresistance recording of the radiation intensity of the combustion products, the conditions under which soot formation occurs are determined.
- 1 September 2022
- Published by Pleiades Publishing Ltd in Thermophysics and Aeromechanics
- Vol. 29 (5) , 791-803
Combustion of boron particles air suspension
Mathematical simulation was applied to evaluating the flame spreading and the flame front speed through the air suspension of boron particles as a function of pressure, excess oxidant ratio, and the particle size. Calculation accounts for a change in heat and mass transfer with a reduction of the particle size from micro-size to nano-scale. The model of flame front propagation through boron particle suspension in air (with account for molecular-kinetic mechanism of heat and mass transfer) allows estimating the normal speed of flame propagation as a function of initial size of boron particles, oxidant excess ratio, and pressure. The conditions were estimated and existence of extremes and flat zones on the curves was justified from a change in heat and mass transfer due to transition from the continuous medium flow to free-molecular flow regime.
- 1 September 2022
- Published by Pleiades Publishing Ltd in Thermophysics and Aeromechanics
- Vol. 29 (5) , 791-803
Combustion of boron particles air suspension
Mathematical simulation was applied to evaluating the flame spreading and the flame front speed through the air suspension of boron particles as a function of pressure, excess oxidant ratio, and the particle size. Calculation accounts for a change in heat and mass transfer with a reduction of the particle size from micro-size to nano-scale. The model of flame front propagation through boron particle suspension in air (with account for molecular-kinetic mechanism of heat and mass transfer) allows estimating the normal speed of flame propagation as a function of initial size of boron particles, oxidant excess ratio, and pressure. The conditions were estimated and existence of extremes and flat zones on the curves was justified from a change in heat and mass transfer due to transition from the continuous medium flow to free-molecular flow regime.
- Open Access
Non-Invasive Acoustic Monitoring of Gas Turbine Units by Fiber Optic Sensors
In this article, we study the possibility of gas turbine unit (GTU) monitoring using interferometric fiber optic sensors. We used the Mach–Zehnder interferometer (MZI) scheme, which can be easily implemented and simply installed on the turbine, and also allows us to solve the problem of phase unwrapping conveniently. In this research, the following main steps were carried out: an experimental scheme based on the MZI was assembled, and its sensitive arm was fixed on the GTU under study; data on various operation modes of the GTU was collected; the data were subjected to frequency FFT analysis, based on which the main rotational speeds of the turbine were identified. With FFT analysis, we also demonstrated multiples harmonics, which appear in the case of GTU after operating time, caused by the number of blades. The possibility of GTU monitoring and analysis using a non-invasive compact fiber-optic sensor is demonstrated: spectral analysis is used to detect the rotor speed, as well as the presence or absence of high-order multiple frequencies indicating blade and bearing defects, which are determined by the number of GTU’s blades and rolling bearing used as turbines rotor supports.
Open AccessNon-Invasive Acoustic Monitoring of Gas Turbine Units by Fiber Optic Sensors
In this article, we study the possibility of gas turbine unit (GTU) monitoring using interferometric fiber optic sensors. We used the Mach–Zehnder interferometer (MZI) scheme, which can be easily implemented and simply installed on the turbine, and also allows us to solve the problem of phase unwrapping conveniently. In this research, the following main steps were carried out: an experimental scheme based on the MZI was assembled, and its sensitive arm was fixed on the GTU under study; data on various operation modes of the GTU was collected; the data were subjected to frequency FFT analysis, based on which the main rotational speeds of the turbine were identified. With FFT analysis, we also demonstrated multiples harmonics, which appear in the case of GTU after operating time, caused by the number of blades. The possibility of GTU monitoring and analysis using a non-invasive compact fiber-optic sensor is demonstrated: spectral analysis is used to detect the rotor speed, as well as the presence or absence of high-order multiple frequencies indicating blade and bearing defects, which are determined by the number of GTU’s blades and rolling bearing used as turbines rotor supports.
- 21 February 2022
- Published by Pleiades Publishing Ltd in High Temperature
- Vol. 60 (1) , 79-84
Technique for Recording and Analysis of the Amplitude Spectrum of the Strength Oscillations of Magnetic and Electric Fields of Combustion Products in a Model Liquid Rocket Engine Fuel Depending on the Combustion Chamber Pressure
The technique and results of the correlational and spectral analyses of the electrophysical characteristics of the combustion products of oxygen- and kerosene-based fuel, recorded with noncontact primary-measuring electromagnetic transducers during the firing tests of a model liquid rocket engine, are presented. A technique is developed for secondary processing sets of electromagnetic field parameters for the correlational and spectral analyses of a duty parameter (combustion chamber pressure) and a parameter to be determined (strength of the electromagnetic field of the combustion products) in the 0–28 kHz range. The maxima of the amplitude spectrum of signals from the magnetic and electric field sensors at frequencies of 114 and 49 Hz, respectively, are determined, and a near-linear (with the correlation coefficient of 0.863) dependence of the amplitude of the strength oscillations of the magnetic field of the combustion products on the combustion-chamber pressure in the model liquid-fuel rocket engine, which can be used for the diagnostics of the working process parameters in the chamber of a liquid rocket engine, is derived.
- 21 February 2022
- Published by Pleiades Publishing Ltd in High Temperature
- Vol. 60 (1) , 79-84
Technique for Recording and Analysis of the Amplitude Spectrum of the Strength Oscillations of Magnetic and Electric Fields of Combustion Products in a Model Liquid Rocket Engine Fuel Depending on the Combustion Chamber Pressure
The technique and results of the correlational and spectral analyses of the electrophysical characteristics of the combustion products of oxygen- and kerosene-based fuel, recorded with noncontact primary-measuring electromagnetic transducers during the firing tests of a model liquid rocket engine, are presented. A technique is developed for secondary processing sets of electromagnetic field parameters for the correlational and spectral analyses of a duty parameter (combustion chamber pressure) and a parameter to be determined (strength of the electromagnetic field of the combustion products) in the 0–28 kHz range. The maxima of the amplitude spectrum of signals from the magnetic and electric field sensors at frequencies of 114 and 49 Hz, respectively, are determined, and a near-linear (with the correlation coefficient of 0.863) dependence of the amplitude of the strength oscillations of the magnetic field of the combustion products on the combustion-chamber pressure in the model liquid-fuel rocket engine, which can be used for the diagnostics of the working process parameters in the chamber of a liquid rocket engine, is derived.
- Open Access
Study of Intra-Chamber Processes in Solid Rocket Motors by Fiber Optic Sensors
In this study, an experimental study of the burning rate of solid fuel in a model solid propellant rocket motor (SRM) E-5-0 was conducted using a non-invasive control method with fiber-optic sensors (FOSs). Three sensors based on the Mach–Zehnder interferometer (MZI), fixed on the SRM E-5-0, recorded the vibration signal during the entire cycle of solid fuel burning. The results showed that, when using MZI sensors, the non-invasive control of solid fuel burnout is made possible both by recording the time of arrival of the combustion front to the sensor and by analyzing the peaks on the spectrogram of the recorded FOS signal. The main mode of acoustic vibrations of the chamber of the model SRM is longitudinal, and it changes with time, depending on the chamber length. Longitudinal modes of the combustion chamber were detected by MZI only after the combustion front passed its fixing point, and the microphone was unable to register them at all. The results showed that the combustion rate was practically constant after the first second, which was confirmed by the graph of the pressure versus time at the nozzle exit.
Open AccessStudy of Intra-Chamber Processes in Solid Rocket Motors by Fiber Optic Sensors
In this study, an experimental study of the burning rate of solid fuel in a model solid propellant rocket motor (SRM) E-5-0 was conducted using a non-invasive control method with fiber-optic sensors (FOSs). Three sensors based on the Mach–Zehnder interferometer (MZI), fixed on the SRM E-5-0, recorded the vibration signal during the entire cycle of solid fuel burning. The results showed that, when using MZI sensors, the non-invasive control of solid fuel burnout is made possible both by recording the time of arrival of the combustion front to the sensor and by analyzing the peaks on the spectrogram of the recorded FOS signal. The main mode of acoustic vibrations of the chamber of the model SRM is longitudinal, and it changes with time, depending on the chamber length. Longitudinal modes of the combustion chamber were detected by MZI only after the combustion front passed its fixing point, and the microphone was unable to register them at all. The results showed that the combustion rate was practically constant after the first second, which was confirmed by the graph of the pressure versus time at the nozzle exit.
- 21 August 2020
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 56 (4) , 471-478
Effect of Particle Size on Boron Combustion in Air
Mathematical modeling of combustion of micron-sized and nanometer boron particles in air with allowance for changes in the heat and mass transfer mechanism and a decreasing particle size is carried out. The Knudsen number is taken as an indicator of a transition from one state to another: a continuous medium assumption is valid for describing the heat and mass transfer mechanisms in the case where Kn \(<\) 0.01, the free molecular regime takes place for Kn \(>\) 10, and a transient state occurs for 0.01 \(<\) Kn \(<\) 10. Particle sizes at which different heat and mass transfer regimes occur with respect to boron combustion in air at pressures of 0.1–4 MPa are estimated. The time it takes for boron particles to combust within the framework of the assumption of a continuous medium and in a free molecular mode is determined. It is shown that calculation models for determining the burning time of boron particles with initial sizes close to micron-sized and nanodispersed ones should take into account a change in the heat and mass transfer mechanism with variation in the current particle radius during burnout.- 21 August 2020
- Published by Pleiades Publishing Ltd in Combustion, Explosion, and Shock Waves
- Vol. 56 (4) , 471-478
Effect of Particle Size on Boron Combustion in Air
Mathematical modeling of combustion of micron-sized and nanometer boron particles in air with allowance for changes in the heat and mass transfer mechanism and a decreasing particle size is carried out. The Knudsen number is taken as an indicator of a transition from one state to another: a continuous medium assumption is valid for describing the heat and mass transfer mechanisms in the case where Kn \(<\) 0.01, the free molecular regime takes place for Kn \(>\) 10, and a transient state occurs for 0.01 \(<\) Kn \(<\) 10. Particle sizes at which different heat and mass transfer regimes occur with respect to boron combustion in air at pressures of 0.1–4 MPa are estimated. The time it takes for boron particles to combust within the framework of the assumption of a continuous medium and in a free molecular mode is determined. It is shown that calculation models for determining the burning time of boron particles with initial sizes close to micron-sized and nanodispersed ones should take into account a change in the heat and mass transfer mechanism with variation in the current particle radius during burnout.