Herman Fidder
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Herman Fidder has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jeff. Th. M. De Hosson
Department of Applied Physics, Zernike Institute for Advanced Materials, University of Groningen, 9747AG Groningen, The Netherlands
2 shared publications - Annelize Botes
Council for Scientific & Industrial Research (CSIR), Pretoria, South Africa
1 shared publication E. Dumont
1 shared publication- Indranil Basu
Laboratory of Metal Physics and Technology, Department of Materials, ETH Zurich, Zurich, Switzerland
1 shared publication J.Th.M. De Hosson
1 shared publicationR.J. Van Velden
1 shared publication
Latest Publications
- Open Access
- 15 July 2025
- Published by Elsevier in Chemical Engineering Science
- Vol. 318
The effect of particle surface roughness and biofilm accumulation on the pressure drop over a biofilter
- 15 July 2025
- Published by Elsevier in Chemical Engineering Science
- Vol. 318
Open AccessThe effect of particle surface roughness and biofilm accumulation on the pressure drop over a biofilter
- Open Access
- 6 July 2023
- Published by Elsevier in Acta Materialia
- Vol. 256
Twinning induced spatial stress gradients: Local versus global stress states in hexagonal close-packed materials
- 6 July 2023
- Published by Elsevier in Acta Materialia
- Vol. 256
Open AccessTwinning induced spatial stress gradients: Local versus global stress states in hexagonal close-packed materials
- Open Access
- 9 July 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (20) , 14713-14728
Response of Ti microstructure in mechanical and laser forming processes
Microstructural deformation mechanisms present during three different forming processes in commercially pure Ti were analysed. Room temperature mechanical forming, laser beam forming and a combination of these two processes were applied to thick metal plates in order to achieve the same final shape. An electron backscatter diffraction technique was used to study the plate microstructure before and after applying the forming processes. Substantial differences among the main deformation mechanisms were clearly detected. In pure mechanical forming at room temperature, mechanical twinning predominates in both compression and tensile areas. A dislocation slip mechanism inside the compression and tensile area is characteristic of the pure laser forming process. Forming processes which subsequently combine the laser and mechanical approaches result in a combination of twinning and dislocation mechanisms. The Schmid factor at an individual grain level, the local temperature and the strain rate are factors that determine which deformation mechanism will prevail at the microscopic level. The final microstructures obtained after the different forming processes were applied are discussed from the point of view of their influence on the performance of the resulting formed product. The observations suggest that phase transformation in Ti is an additional microstructural factor that has to be considered during laser forming.
- 9 July 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (20) , 14713-14728
Open AccessResponse of Ti microstructure in mechanical and laser forming processes
Microstructural deformation mechanisms present during three different forming processes in commercially pure Ti were analysed. Room temperature mechanical forming, laser beam forming and a combination of these two processes were applied to thick metal plates in order to achieve the same final shape. An electron backscatter diffraction technique was used to study the plate microstructure before and after applying the forming processes. Substantial differences among the main deformation mechanisms were clearly detected. In pure mechanical forming at room temperature, mechanical twinning predominates in both compression and tensile areas. A dislocation slip mechanism inside the compression and tensile area is characteristic of the pure laser forming process. Forming processes which subsequently combine the laser and mechanical approaches result in a combination of twinning and dislocation mechanisms. The Schmid factor at an individual grain level, the local temperature and the strain rate are factors that determine which deformation mechanism will prevail at the microscopic level. The final microstructures obtained after the different forming processes were applied are discussed from the point of view of their influence on the performance of the resulting formed product. The observations suggest that phase transformation in Ti is an additional microstructural factor that has to be considered during laser forming.