MSMartin Stockmann

Martin Stockmann

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Martin Stockmann has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Fragmentation Criterion for the Interface of a Hydrostatic Extruded Al-Mg-Compound

    by Carola Kirbach, Martin Stockmann, Jörn Ihlemann

    Due to the higher demand for energy efficient products, light-weight constructions have become more important in recent years. An innovative, hydrostatic extruded Al-Mg-compound used here combines the corrosion resistance of aluminium with the outstanding lightweight properties of magnesium. During the production process, a thin boundary layer is built between the two basic materials. Investigations on further hot forming processing revealed a good formability of these compounds despite the fact that the boundary layer splits into fragments during forging and a new secondary boundary layer is built when the basic materials between the fragments come into contact again during the continuous deformation. The aim of the research is now to investigate fragmentation depending on the deformation rate and boundary layer thickness, which increases during the heat-up process in preparation of forging. For this purpose, a channel compression test is used in conjunction with a special newly developed specimen shape. The metallographic evaluation of the boundary layer reveals a strong dependency of fragmentation on the deformation rate and the boundary layer thickness. With the aid of a numerical simulation, an individual critical stretch could be determined at which fragmentation starts, and provide guidance for an optimal forging process design.


  • Untersuchungsstrategie zur Bewertung der Langzeitstabilität von Dehnungsmessstreifen

    by Ralf Herrmann, Martin Stockmann, Steffen Marx

    Im Bauwerksmonitoring werden neben Temperaturen und Verschiebungen meist Dehnungen gemessen. Dies dient u. a. dazu, den Ausnutzungsgrad und die Betriebsfestigkeit zu beurteilen. Ein sehr gebräuchliches Verfahren zur Bestimmung von Dehnungen an und in Bauteilen ist die Messung mit Dehnungsmessstreifen (DMS). Für die Beurteilung der Langzeitstabilität von Dehnungsmessstreifen wird im Folgenden eine Klimaprüfung vorgestellt, die eine beschleunigte Beanspruchungseinwirkung durch Temperatur‐ und Feuchteschwankungen simuliert. Dieser sich wiederholende Zyklus besteht aus vier Phasen, die insgesamt 240 h umfassen und dabei unterschiedliche Kombinationen von Temperatur und Luftfeuchtigkeit bis hin zu Frost‐Tau‐Wechseln beinhalten. Anhand von Ergebnissen aus durchgeführten Langzeituntersuchungen über einen Zeitraum von 85 d werden Kenngrößen zur Charakterisierung der Langzeitstabilität von Dehnungsmessstreifen abgeleitet. Die Messergebnisse zeigen Unterschiede in der Nullpunktdrift zwischen den einzelnen Typen von Dehnungsmessstreifen und welche Bedeutung der Auswahl und dem Schutz von Dehnungsmessstreifen beigemessen werden muss.Test strategy for evaluation of strain gauge long term stabilityIn the field of structural health monitoring the measuring of strain is prevalent beside temperature and displacement. The strain is used to determine the utilization rate and to estimate the fatigue strength of a structure. A very common measurement method for strains at and in components is the usage of strain gauges. Further, a climate cycle for analysis of long term stability of strain gauges is introduced, that simulates an accelerated temperature and humidity stress. This cycle consists of four phases, which lasts 240 h and covers different combinations of temperature and humidity conditions up to freezing and thawing. The results of a 85 d lasting long term test are presented and used to describe characteristic values for long term stability of strain gauges. The measurement results show significant differences for the strain gauge types in the zero point drift and underline the role of correct choice and protection to achieve reliable strain measurements.


  • Open Access

    Experimental determination and modelling of volume shrinkage in curing thermosets

    by Martin Rudolph, Martin Stockmann, Ralf Landgraf, Jörn Ihlemann

    This work deals with the characterisation and modelling of the curing process and its associated volume changes of an epoxy based thermoset resin. Measurements from differential scanning calorimetry (DSC) define the progress of the chemical reaction. The related thermochemical volume changes are recorded by an especially constructed experimental setup based on Archimedes principle. Information on measuring procedure and data processing are provided. This includes investigations on compensation of environmental influences, long-term stability and resolution. With the aim of simulating the adhesives curing process, constitutive models representing the reaction kinetics and thermochemical volume changes are presented and the model parameters are identified.